brake rotor JAGUAR X308 1998 2.G Workshop Manual

Front Suspension -
Lubri
cants, Fluids, Sealants and Adhesives
Press-In Loads
Torques


UnitS
pecification
Loctite27

0
Greas

e
Shell Retin
ax 'A'
Greas

e
Castro
l 'NTR'
Com

ponent
Kn
Ball join

t to upper wishbone
25
- 50
B

all joint to lower wishbone
25
- 50
Com

ponent
Nm
N

ut - ball joint, upper wishbone to vertical link.
60
-80
N

ut - ball joint, lower wishbone to vertical link.
60
-80
Nu

t - fulcrum bolt, upper wishbone.
60
-80
N

ut - ball joint, tie rod to steering arm.
71
-85
Bol

t - wheel speed sensor to vertical link.
8-1
0
Bol

t - front mounting to crossbeam.
22
-28
Bolt

- mounting , stabilizer bar.
30
-40
N

ut - link arm ball joint to stabilizer bar.
60
-80
Bolt

- mounting, steering rack to crossbeam.
41
-54
B

olt - front mounting, crossbeam to body.
22
-28
Bol

t - spring pan to lower wishbone.
70
-90
N

ut - shock absorber to upper mounting
(vehicles with adaptive damping).
16
-18
Nu

t - shock absorber to upper mounting (vehicles without adaptive damping).
30
-40
N

ut - shock absorber lower to wishbone.
43
-57
B

olt - engine Hydramount to crossbeam.
34
-46
B

olt - crossbeam rear mounting to body.
13
1-185
Bol

t - generator cooling du
ct deflector to crossbeam.
17
-23
N

ut - lower steering column to pinion shaft.
22
-28
N

ut - hub, speed sensor rotor.
27
0-330
B

olt - shield, brake disc.
9-1
2
Bol

t - lower wishbone, front arm to rear arm.
77
-103
Nu

t - stabilizer bar link arm to wishbone bracket.
41
-54
N

ut - wishbone front
eccentric bolt.
11
3-153
Nu

t - wishbone rear
eccentric bolt.
11
3-153
N

ut - fulcrum shaft, upper wishbone.
60
-80
Bolt -

power steering pi
pes to pinion housing.
9-1
2

Upper
Wishbones
Each
upper wi
shbone assembly is a on
e-piece steel forging incorporating:
A pres
s-fit ball joint.
Press-fi

t bushes for location of the upper fulcrum bolt.
Lower Wishbones
Each l
o
wer wishbone comprising
forged steel front and rear arms bolted together, incorporates:
A p
ress-fit ball joint in the outer extremity of the rear arm.
Press-f
i
t bushes for location of the lower fulcrum bolts
Locati
on for the shock absor
b
er lower mounting plates.
Vertica l Links

The vertical
links are of forged steel
wi
th integral steering arms. Each is suppo rted between the upper and lower wishbones
by two ball joints and carries:
Front hub

Brake ca
liper and disc shield assembly

ABS se
nsor
.
Front Hub
s

Each f
o
rged steel front hub accommodates sealed for life cartridge
type wheel bearings, and carries:
The brake rotor assembl
y.
A
h
ub nut with toothed, integral ABS rotor.
Su
s
pension spring pi
n locking device.
Front Road
Springs
The road spri
ng
s are of coil type with their
rating dependent upon vehicle specification
Ea
ch spring is installed between the suspension crossbeam location and the lower wishbone spring pan.
Ru
bber seats ar
e installed betw
een the spring and the crossb eam and the spring pan.
Front Shock A
bsorbers
Th
e
shock absorbers are telescopic hydrau
lically operated units. Optional adaptive damping units incorporate a solenoid-
operated control valve at their upper extremity.
Each shoc
k absorber is installed between the lowe
r wishbone rear arm and a recess in the body.
The l
o
wer end of the shock absorber is se
cured to plates on the wishbone by a bolt that also serves as a pivot.
The u
pper en
d of each shock absorber is secured to the body location by a single nut.
Front Sta
b
ilizer Bar
A
front stabil
izer bar installed on all vehicles
is rated according to suspension specification.
Opera
tion
As each road wheel r
i
ses, move
ment is transmitted through the vertical link assembly to the lower wishbone. The resulting
rise of the wishbone compresses the road spring and partially telescopes the shock absorber. During this action, the spring
absorbs associated shocks and the shock absorber minimizes sprin
g os c
illation.

Du

ring cornering, vehicle weight
is transferred to the outer road wheel with a resulting tendency for the inner wheel to lift.
The stabilizer bar assists in minimizing this tendency by transf erring a proportion of potential lift of the inner wheel to the
outer wheel. This result s in enhanced body stability with improved corner ing capabilities.

Remova
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devises are used on nuts and bolts throughout the
vehicle. These devises restrict the number of times a nut or bolt can be used. See section 100-00 for information.

1 8
G 1004
1.
Re
move vertical link and hub as
sembly. Refer to 60.25.38.90.

2. Re
move brake disc shield from vertical link.
1. Remove screws.
2. Remove disc shield.

3. Us
ing special tool, secure vertical link and hub assembly in a
vise.
Secure special tool
in a vise.
Posit
i
on hub in tool.
Inst
al
l wheel nuts.

4. Re
move rotor nut spring-clip.
5. Remove rotor nut.
Us
ing special tool 206-066A remove rotor nut.

Remova
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devises are used on nuts and bolts throughout the
vehicle. These devises restrict the number of times a nut or bolt can be used. Refer to Section 100-00 for further
information.

1 8
G 1004
1.
Ra
ise front of vehicle and support on stands. Refer to Section
100-02.
2. Remove appropriate road wheel. Refer to Section 100-02.
3. Remove front brake disc. Refer to 70.10.12.
4. Remove vertical link and hub assembly. Refer to operation
60.25.38.90.

5. Re
move brake-disc shield from vertical link.
1. Remove screws.
2. Remove disc shield.

6. Us
ing special tool, secure vertical link and hub assembly in a
vise.
Secu re spe
cial tool 204-195 in a vise.
Posit
i
on hub in tool.
Inst
al
l wheel nuts.
7. Remove rotor nut spring-clip.

Remova
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devises are used on nuts and bolts throughout the
vehicle. These devises restrict the number of times a nut or bolt can be used. See section 100-00 for information.

1 8
G 1004
1.
Ra
ise front of vehicle and support on stands. Refer to Section
100-02.
2. Remove appropriate road wheel. Refer to Section 100-02.
3. Remove front brake disc. Refer to 70.10.12.
4. Remove vertical link and hub assembly. Refer to operation
60.25.38.90.

5. Re
move brake-disc shield from vertical link.
1. Remove screws.
2. Remove disc shield.

6. Us
ing special tool, secure vertical link and hub assembly in a
vise.
Secure special tool
in a vise.
Posit
i
on hub in tool.
Inst
al
l wheel nuts.

7. Re
move rotor nut spring-clip.

26. CAUTI
ON: Note position of
shims during removal. They
must be returned to their original positions during installation.
Noting positions, remove shim from each end of pivot pin
sleeve.

27 . W
ithdraw pivot pin sleeve from hub carrier.

28 .
Using a h
ydraulic press,
remove hub from carrier.
Plac
e large section of special tool 204-113 on press bed,
with recess in t ool uppermost.
Positi
on hub carrier on tool
, ensuring handbrake cable
housing locates in tool recess.
Posit i
on small section of special tool on hub. 204-113.
Align to
ol to press-r
am, and
operate press to remove hub
from hub carrier.
29. Place hub carrier on a work bench.
30. Withdraw ABS rotor from hub carrier.

1.
Position hub carrier on block of wood.
2. Position ABS-rotor sensor to hub.
Ali g
n assembly to press-ram, and operate press to install
ABS-sensor rotor to hub.

10 . CAUTI
ON: Do not use excessive force when levering
hub.
Measure hub end-float.
Secure hub carri er in vi
ce.
Inst
al
l special tool JD15 to hub.
1. Install dial gauge JD 13A on hub carrier.
2. Using two levers, measure and record hub end-float.
R e
move special tools from hub carrier.

11
. Using h
ydraulic pr
ess, remove hub and outer bearing
assembly from carrier.
1. Position large section of special tool JD132 on press bed, with recess in tool upper most.
2. Position hub carrier on tool, ensuring parking brake cable housing locates in tool recess.
3. Position small section of special tool JD132 on hub.
Alig
n assembly to press-ram, and operate press to remove

hub from hub carrier.

12 . R
emove ABS rotor and inner bearing from hub carrier.
R
e
move ABS rotor.
R
e
move inner bearing.
13. Remove outer bearing assembly from hub.
Remove bearing shim.

28. Using a h
ydraulic press,
remove hub from carrier.
Pla
ce large section of special tool (204-113) on press bed,
with recess in t ool uppermost.
Positi
on hub carrier on tool
, ensuring handbrake cable
housing locates in tool recess.
P o
sition small section of spec
ial tool (204-113) on hub.
Align tool to press-r
am, and
operate press to remove hub
from hub carrier.
29. Place hub carrier on a work bench.

30 . W
ithdraw ABS rotor from hub carrier.

31 . Remove ou
ter seal and bearin
g assembly from hub carrier.
Using a drift, re
move an
d discard outer seal.
Remove ou ter bearin
g.
Re
mo
ve bearin
g spacer.
Remove bearin g shim.
32
.
Remove inner seal and bearing from hub carrier.
Using a drift, re
move and discard inner seal.
Re

move inner bearing.

Anti-Lock Control -
Lubri
cants, Fluids, Sealants and Adhesives
Torques
Brake Tube, Hoses and Bracket Torques
CAUTI
ON: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.


UnitS
pecification
Brake flu

id
ITT Supe
r Dot 4
Com

ponent
Nm
Bol

t - front wheel speed sensor
8-
10
Bolt

- rear wheel speed sensor
8-
10
Bo

lt - hydraulic control unit to bracket
8-
10
Bolt -

hydraulic control unit bracket to body
10
-14
Hub rotor nut2

70-330
Com

ponent
Nm
Bleed n

ipple - front
4-
6
Bleed n

ipple - rear
8-1
1
Hose to fr

ont caliper
10
-14
Hose banjo to rear caliper -

bolt
30
-40
M1

0 hose locknut
15
-20
M10

brake tube female-nut
13
-17
M10

brake tube male-nut
13
-17
M12

brake tube male-nut
15
-20
M18

brake tube male-nut
22
-28
Brake tube clip retention

-bracket to body
4-
6

Anti-Lock Control - Wheel Speed Se
nsor Ring
Re
mo
val and Installation
Remov
a
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
S p
ecial Tool(s)

Hub Holdin
g Tool
2
04-195 (JD 227)

ABS Rotor Nut Socket
2
06-
066A
1.
Op
en engine compartment and
fit paintwork protectors to
fenders.
2. Raise front of vehicle and support on stands. Refer to section
100-02.
3. Remove front wheel. Re fer to section 204-04.
4. Remove front brake disc. Refer to operation 70.10.12.
5. Remove vertical link and hub assembly. Refer to operation
60.25.38.90.

6. Re
move brake-disc shield from vertical link.
1. Remove screws.
2. Remove disc shield.
7. Using special tool, secure vertical link and hub assembly in a
vice.
Secure special tool
in a vice.
Posit
i
on hub in tool.
Fit and

tighten wheel nuts.