coolant temperature JAGUAR XF 2009 1.G AJ133 5.0L Engine Manual

Technical Training
NP10-V8JLR: AJ133 5.0-Liter DFI V8 Engine 04/14/2009
3-1
Engine Management System

Table of Contents

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Engine Control Module . . . . . . . . . . . . . . . . . . . . . . 8
Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Crankshaft Position Sensor . . . . . . . . . . . . . . . . . . 11
Camshaft Position Sensor . . . . . . . . . . . . . . . . . . . 13
Engine Coolant Temperature Sensor . . . . . . . . . . 14
Knock Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Manifold Absolute Pressure Sensor . . . . . . . . . . . 16
Mass Air Flow Sensor . . . . . . . . . . . . . . . . . . . . . . 17
Temp. / Manifold Absolute Pressure Sensor . . . . 18
Throttle Position Sensor . . . . . . . . . . . . . . . . . . . . 19
Accelerator Pedal Position Sensor . . . . . . . . . . . . 21
Heated Oxygen Sensors . . . . . . . . . . . . . . . . . . . . 22
Ambient Air Temperature Sensor. . . . . . . . . . . . . 26
Ignition Coils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Fuel Tank Canister Purge Valve . . . . . . . . . . . . . . 28
Viscous Fan Control (Land Rover only) . . . . . . . 29
Controller Area Network. . . . . . . . . . . . . . . . . . . . 30
On-Board Diagnostic Monitoring . . . . . . . . . . . . . 31
Crankcase Ventilation System . . . . . . . . . . . . . . . 32

3-6
04/14/2009 NP10-V8JLR: AJ133 5.0-Liter DFI V8 Engine
Technical Training
Overview

Engine Management System

SC Component Location: Rear of Engine
NP10V8092
FUEL RAIL
PRESSURE S ENSOR
ENGINE
COOLANT TEMP. SENS OR
UPSTREAM
UHEGO
DOWNS TREAM
HO2S (2)
CRANKS
HAFT
POS ITION S ENSOR
UPS
TREAM
UHEGO
ENGINE
CONTROL MODULE KNOCK
S ENS ORS (4) TEMPERATURE AND
MANIFOLD ABS OLUTE PRESSURE S ENSOR

3-8
04/14/2009 NP10-V8JLR: AJ133 5.0-Liter DFI V8 Engine
Technical Training
Engine Control Module

Engine Management System

ENGINE CONTROL MODULE
The ECM is supplied with battery voltage from a 5A fuse and an ignition supply from the ECM relays through\
a 15A
fuse, both located in the CJB. A regulator located within the ECM supplies a 5V current to internal compone\
nts such
as the microprocessor unit. Other components or functions requiring full\
battery voltage are controlled by external
relays or internal switching modules.
The microprocessor within the ECM receives signals from different components and control modules and uses a pro-
gram within the ECM software to interpret the signal information and issue signals which relate t\
o how the engine
components and functions should be controlled. The ECM communicates with other control modules via bidirectional
Controller Area Network (CAN) communication interfaces.
The ECM uses the following inputs and outputs:
Inputs
• Camshaft position (CMP) sensor
• Crankshaft position (CKP) sensor
• Fuel rail high-pressure sensor
• Mass air flow (MAF) sensors (2)
• Knock sensors (4)
• Engine coolant temperature (ECT) sensor
• Manifold absolute pressure (MAP) sensor
• Electronic throttle position sensor
• Accelerator pedal position (APP) sensor
• Cooling fan speed
• Upstream Universal Heated Exhaust Gas Oxygen (UHEGO) sensors (2)
• Brake switch
• Speed control cancel/suspend switch
• Intake air temperature (IAT) sensor (integrated into the MAF) (2)
• Ambient air temperature (AAT) sensor
• Engine oil level and temperature sensor
• Temperature and manifold absolute pressure (TMAP) sensor (SC only)
Outputs

• Throttle Actuator
• Coil-on-plug (COP) ignition coils (8)
• Upstream Universal Heated Exhaust Gas Oxygen (UHEGO) sensors (2)
• Downstream Heated Oxygen Sensors (HO2S) (2)
• Direct injection fuel injectors (8)
• Variable camshaft timing (VCT) solenoids (4)
• Camshaft profile switching (CPS) solenoids (2)
• Intake manifold tuning solenoid
• Carbon canister purge valve
• Fuel pump relay
• Starter relay
• A/C condenser fan relay
• ECM main relay viscous fan control
• Generator control
• Air flap solenoid (SC only)
• Pump control diagnostics
• Diagnostic Monitoring of Tank Leakage (DMTL)

3-14
04/14/2009 NP10-V8JLR: AJ133 5.0-Liter DFI V8 Engine
Technical Training
Engine Coolant Temperature Sensor

Engine Management System

ENGINE COOLANT TEMPERATURE SENSOR
The engine coolant temperature (ECT) sensor is a nega-
tive temperature coefficient (NTC) thermistor, used to
monitor engine coolant temperature.
The ECT sensor is vital to the correct running of the
engine, as a richer mixture is required at lower block
temperatures for good quality starts and smooth running,
leaning off as the temperature rises to maintain emis-
sions and performance.
The sensor has a twist-lock design with a latch mecha-
nism, and is located at the rear of the engine in the water
crossover pipe, between the two heads.
Failure Modes
• Uses engine-off time and MAF for calculation
Failure Symptoms
• Poor cold and hot start
• Poor driveability
• Cooling fans on permanently
Sensor Resistance vs. Coolant Temperature
NOTE:
If the ECT sensor fails, the ECM uses a default
value. The electric fan control module is sent a default
coolant temperature value and switches the cooling
fan(s) on permanently.
The voltages shown represent the signal processed by
the ECM. When a defective coolant sensor is detected,
the coolant value defaults to 40°C (104°F) and remains
fixed until the ECM is powered down.
NP10V8099

Specification
Function
Supply voltage 5V ± 0.1V
Operating temperature range -30°C to 125°C
(-22°F – 257°F)
Pin 1 Sensor output signal
Pin 2 Sensor ground

Coolant Temperature
Approx. Resistance
-20°C (-4°F) 15.04 +0.90/-0.83 kOhms 20°C (68°F) 2.45 +0.10/-0.09 kOhms
80°C (176°F) 0.318 ±0.007 k Ohms
110°C (230°F) 0.1471 ±0.0018 k Ohms