brake JAGUAR XFR 2010 1.G Workshop Manual

Published: 11-May-2011
Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake Disc Vehicles With: High Performance Brakes
Removal and Installation

Removal


CAUTION: Brake discs must be renewed in pairs.


NOTE: Removal steps in this procedure may contain installation details.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Brake Pads - Vehicles With: High Performance Brakes (206-03B Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol,
Removal and Installation).

3. Torque: 115 Nm 4.
Remove the 2 clips.
Clean the components mating faces.













Installation 5. Repeat the above procedure on the opposite side.

1. To install, reverse the removal procedure.

Published: 11-May-2011
Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake Pads Vehicles With: High Performance Brakes
Removal and Installation

Removal


CAUTION: Brake fluid will damage paint finished surfaces. If spilled, immediately remove the fluid and clean the area
with water.


NOTE: Removal steps in this procedure may contain installation details.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

2. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

3.

7. WARNING: If the brake caliper piston seal is damaged
a new brake caliper must be installed.


CAUTION: Do not allow the brake caliper to hang on
the brake hose.


NOTE: Left-hand shown, right-hand similar.
















8. NOTE: Left-hand shown, right-hand similar.
Release the clip.














9. NOTE: Left-hand shown, right-hand similar.

10.




















11.
Repeat the above procedure on the opposite side.

Installation


1. WARNING: Do not use compressed air to clean brake components.
Dust from friction materials can be harmful if inhaled.


CAUTION: As the piston is pushed back into the caliper housing,
the brake fluid level in the reservoir will rise. Do not allow the reservoir
to overflow.
Press the piston into the caliper housing.

2.

8.
9. CAUTIONS:


Make sure that the road wheels are in the straight
ahead position.


Make sure that excessive force is not used. Failure to
follow this instruction may result in damage to the vehicle.


Make sure that the brake hose is not twisted and is
correctly located.
Pull downwards at the position shown.









10. Repeat the above procedure on the opposite side.

11. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

Published: 11-May-2011
Front Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Brake Disc Shield Vehicles With: High Performance Brakes
Removal and Installation

Removal

1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

2. Remove the front brake disc.
For additional information, refer to: Brake Disc - Vehicles With: High Performance Brakes (206-03A Front Disc Brake - V6 3.0L Petrol, Removal and Installation).

3. Remove the brake disc shield.
Remove the 2 rivets.













Installation

1. To install, reverse the removal procedure.
Install the rivets.

Brake hose to brake caliper 42 31 - Brake caliper anchor plate 103 76 - Brake caliper retaining bolts 28 21 - Brake caliper logo badge retaining bolts - Vehicles with high performance brakes 10 7 -

Published: 11-May-2011
Rear Disc Brake - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol - Rear
Disc Brake - Component Location
Description and Operation













PerformanceBrakes-5.0LSuperchargerV8

1 Retaining washer (2 off) 2 Brake disc 3 Rivet (3 off) 4 Brake dust shield 5 Rear wheel knuckle/hub and bearing assembly 6 Caliper carrier bolt (2 off) 7 Brake pad wear sensor 8 Guide pin dust cover (2 off) 9 Guide pin bush (2 off) 10 Guide pin (2 off) 11 Caliper carrier 12 Brake caliper housing 13 Piston 14 Piston dust cover 15 Inboard brake pad and shim 16 Outboard brake pad 17 Anti-rattle spring 18 Bleed screw 19 Bleed screw dust cap 20 Knurled pin 21 Parking brake lever 22 Parking brake return spring

After any work on the rear brakes, the parking brake must be re-calibrated.
Refer to: Parking Brake (206-05 Parking Brake and Actuation, Description and Operation). www.JagDocs.com