oil JAGUAR XFR 2010 1.G Manual PDF

Engine - V8 S/C 5.0L Petrol - Engine Oil Draining and Filling
General Procedures
Draining Published: 11-May-2011

WARNING: The spilling of hot engine oil is unavoidable during this procedure, care must be taken to prevent scalding.
CAUTION: Correct installation of the oil filler cap can be obtained by tightening the cap until hard stop.
NOTE: Clean the components general area prior to dismantling.


1. CAUTION: Make sure the engine is warm.

Start the engine and allow to run for 10 minutes, stop the engine.

2.













3. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

4.
Loosen the element cover 4 complete turns to allow
engine oil to drain from the filter cover.
Make sure that the O-ring seal is exposed.












5. NOTE: Allow 10 minutes for the engine oil to drain from the oil filter
housing. www.JagDocs.com

6. NOTE: Remove and discard the O-ring seal.
















7. Remove and discard the oil filter element.














8. WARNING: Do not work on or under a vehicle supported only by a
jack. Always support the vehicle on safety stands.

Raise and support the vehicle.

9. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

10. CAUTIONS:


Be prepared to collect escaping oil.


Allow at least 10 minutes for the engine oil to drain.

NOTE: Discard the sealing washer.

Filling


1. CAUTION: Make sure that the area around the
component is clean and free of foreign material.


NOTE: Install a new sealing washer.
Torque: 24 Nm







2. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).


3. NOTE: Install new O-ring seals.

Lubricate the oil filter element O-ring seal with clean
engine oil.













4. CAUTION: Tighten the component finger tight first.
Torque: 25 Nm











5. CAUTION: Make sure that the vehicle is left for 5 minutes from
filling with oil and that the engine oil level is reading at least minimum
(by following Steps 9-13), before starting the engine.

Fill the engine with oil - for filling values on vehicles without
supercharger:

Refer to: Specifications (303-01C Engine - V8 5.0L Petrol, Specifications).
Fill the engine with oil - for filling values on vehicles with
supercharger:

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol, Specifications).
Clean any residual engine oil from the oil filler cap area.

6.













7. CAUTION: Make sure that the vehicle has been left for 5 minutes
from filling with oil.

Follow the Steps 9-13 before starting the engine.

8.
Start the engine and allow to run for 10 minutes, stop the
engine.
Check for leaks.

9. CAUTIONS:


Make sure that the selector lever and the gearshift mechanism are
in the park (P) position.


Make sure that the hood is open.
Turn the ignition on.

12.
The message center display will revert to the normal
display in the trip computer.
Scroll through the trip menu to access the engine oil
level display.
Check that the oil level display shows an oil level
reading.
Only after having started and run the engine for 10
minutes (as indicated in Step 8), switch off the
engine, then stabilizing for 10 minutes, take a
reading from the oil level display and, if necessary
top up with engine oil.





















13. NOTE: If instructed to follow Steps 9-13 in a previous step, return
to Step 8 and continue the procedure.
Turn the ignition off.

14. Allow 10 minutes for the engine oil level to stabilize if there has been
additional oil top up.


15. NOTE: The following steps are to update the average
oil level value.
Turn the ignition on.
Press and hold the cruise control cancel button for
more than 2 seconds. www.JagDocs.com

Published: 11-May-2011
Engine - V8 S/C 5.0L Petrol - Engine Oil Vacuum Draining and Filling
General Procedures

Special Tool(s)


303-1484
Vacuum Pump, Oil Drain

303-1484-01
Adapter for 303-1484
Draining

WARNING: The spilling of hot engine oil is unavoidable during this procedure, care must be taken to prevent scalding.


CAUTION: Correct installation of the oil filler cap can be obtained by tightening the cap until hard stop.

NOTES:


Make sure that the vehicle is parked on level ground.


Clean the components general area prior to dismantling.

1.
Start the engine and allow to run for 10 minutes, stop the
engine.


2. CAUTION: Allow 10 minutes from turning the engine off
before starting oil extraction.











3. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

6.
Remove the oil vacuum pump.

7.

8. NOTE: Discard the O-ring seals.
















Filling

1. NOTE: Install new O-ring seals.
Lubricate the oil filter element O-ring seal with clean
engine oil.













2. CAUTION: Tighten the component finger tight first.
Torque: 25 Nm











3. CAUTION: Make sure that the vehicle is left for 5 minutes from
filling with oil and that the engine oil level is reading at least minimum
(by following Steps 7-11), before starting the engine.

Fill the engine with oil - for filling values on vehicles without
supercharger:

Refer to: Specifications (303-01C Engine - V8 5.0L Petrol, Specifications).
Fill the engine with oil - for filling values on vehicles with
supercharger:

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol,

Specifications).
Clean any residual engine oil from the oil filler cap area.

4.













5. CAUTION: Make sure that the vehicle has been left for 5 minutes
from filling with oil.

Follow the Steps 7-11 before starting the engine.

6.
Start the engine and allow to run for 10 minutes, stop the
engine.
Check for leaks.

7. CAUTIONS:


Make sure that the selector lever and the gearshift mechanism are
in the park (P) position.


Make sure that the hood is open.
Turn the ignition on. www.JagDocs.com

10.
The message center display will revert to the normal
display in the trip computer.
Scroll through the trip menu to access the engine oil
level display.
Check that the oil level display shows an oil level
reading.
Only after having started and run the engine for 10
minutes (as indicated in Step 6), switch off the
engine, then stabilizing for 10 minutes, take a
reading from the oil level display and, if necessary
top up with engine oil.





















11. NOTE: If instructed to follow Steps 7-11 in a previous step, return
to Step 6 and continue the procedure.
Turn the ignition off.

12. Allow 10 minutes for the engine oil level to stabilize if there has been
additional oil top up.


13. NOTE: The following steps are to update the average
oil level value.
Turn the ignition on.
Press and hold the cruise control cancel button for
more than 2 seconds.