JAGUAR XFR 2010 1.G Manual Online
XFR 2010 1.G
JAGUAR
JAGUAR
https://www.carmanualsonline.info/img/21/7642/w960_7642-0.png
JAGUAR XFR 2010 1.G Manual Online
Page 1200 of 3039
14.
15. NOTES:
Lubricate
the union
threads with
clean engine
oil.
Do not
tighten at
this stage.
Remove and
discard the
blanking
caps.
Torque:
union 21 Nm bolts 8 Nm
16.
Torque: 21 Nm
17.
Refer to: Air Cleaner Outlet Pipe RH (303-12C Intake Air Distribution and Filtering - V8 5.0L Petrol, Removal and Installation).
Page 1210 of 3039
5. CAUTION: If a new cylinder head has been installed then the special tool
310-200-02 without the thread must be used to install the fuel rail.
Special Tool(s): 310-200-01, 310-200-02
6. CAUTIONS:
Make sure that the area around the open fuel injector ports are clean
and free of foreign material and lubricant prior to installing the fuel injector.
When Installing the fuel injector(s), make sure that the Teflon seal is
clean and free of foreign material and lubricant.
7. CAUTIONS:
If new fuel injectors are installed, a new injector clamp must be
installed
Make sure that the fuel injector is aligned and installed into the fuel
rail correctly, as noted in the removal step.
Tighten the fuel rail retaining bolts a turn at a time until the correct
torque is achieved.
NOTE: Lubricate the fuel injector O-ring seals with clean engine oil.
Torque: 20 Nm
8. NOTE: LH shown RH similar.
Special Tool(s): 310-200-01, 310-200-02
Page 1212 of 3039
13.
14.
15. NOTE: LH shown RH similar.
Torque: 7 Nm
NOTE: LH shown RH similar.
CAUTION: Lubricate only the union threads with clean engine oil.
NOTES:
Engine shown removed for clarity.
Install the bolt and unions finger tight before final tightening.
Remove and discard the blanking caps.
16. Lower the vehicle. www.JagDocs.com
Page 1215 of 3039
24.
25.
NOTES:
Lubricate the
union threads
with clean
engine oil.
Do not
tighten at
this stage.
Remove
and discard
the blanking
caps.
26. Torque:
Unions 21 Nm Bolts 8 Nm
Page 1222 of 3039
Installation
1. NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with
clean engine oil.
2. CAUTION: Tighten the Torx screws a turn at a time until the
correct torque is achieved.
NOTE: Lubricate the fuel rail high-pressure fuel pump O-ring seal
with clean engine oil.
Torque: 12 Nm
3. Loosen the Torx screws half a turn each. 4. www.JagDocs.com
Page 1224 of 3039
support the vehicle on safety stands.
Raise and support the vehicle.
10.
11. CAUTION: Lubricate only the union threads with clean engine oil.
NOTE: Engine shown removed for clarity.
Torque: Unions (1) 21 Nm M6 (2) 11 Nm M8 (3) 25 Nm M5 nut (4) 6 Nm
NOTE: Engine shown removed for clarity.
Torque: 21 Nm
Page 1227 of 3039
21. NOTES:
Lubricate
the
union
threads
with
clean
engine
oil.
Do
not tighten
at this
stage.
Remove
and
discard
the
blanking
caps.
22. Torque: Unions 21 Nm Bolts 8 Nm
23. Refer to: Air Cleaner Outlet Pipe RH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).
24. www.JagDocs.com
Page 1235 of 3039
Installation
All vehicles
1. NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with
clean engine oil.
2. CAUTION: Tighten on both sides simultaneously. Torque: 12 Nm
3. Loosen the Torx screws half a turn each. 4.
Page 1237 of 3039
Raise and support the vehicle.
10.
11. CAUTION: Lubricate only the union threads with clean engine oil.
NOTE: Engine shown removed for clarity.
Torque: Unions (1) 21 Nm M6 (2) 11 Nm M8 (3) 25 Nm M5 nut (4) 6 Nm
NOTE: Engine shown removed for clarity.
Torque: 21 Nm www.JagDocs.com
Page 1240 of 3039
18. Torque: 35 Nm
All vehicles
19. Refer to: Generator - V8 5.0L Petrol (414-02C Generator and Regulator - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).
20. Refer to: Engine Mount RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
21. Lower the vehicle.
22.
23.
NOTES:
Lubricate
the
union
threads
with
clean
engine
oil.
Do
not tighten
at this
stage.
Remove
and
discard
the
blanking
caps.
