lock JAGUAR XJ6 1994 2.G Workshop Manual

AS. 9.11 Security active indicator
0
1. Check wiring continuity from multi-plug 26-way connector pin 19 to central locking switch
connector pin 13. Ensure secure ground at switch connector pin 16.
If indicator is faulty the whole clock module must be renewed, refer to
sub-section 15.9.10. U&Q:
0
e
0
P191
1
J86.1916
Fig. 1 Security Active Indicator Circuit

Security System - RESTRICTED ISSUE
-
A5.17 FRONT DOOR LOCK ASS€MBLY - RENEW
SRO
86.25.45
Remove the veneer trim pad. See Section 13 of the VSM.
. Remove the upper trim pad. See Section 13 of the VSM.
Remove the lower trim pad. See Section 13 of the VSM.
. Using a suitable plastic knife, cut through the weather- shield to door sealant and pull back the weathershield (1 Fig. 1) for access to the door lock assembly.
. Disconnect the door handle link rod (2 Fig. 1).
. Disconnect the door sill button link rod (3 Fig. 1).
. Disconnect the key barrel link rod (4 Fig. 1).
. Displace and reposition the door lock assembly multi-
Undo and remove the lower securing bolt (5 Fig. 1) from
. Undo and remove the door lock assembly securing bolts
. Displace and reposition the glass frame.
. Displace and reposition the door lock assembly (7 Fig. 1).
Displace and remove the edge clip from the door handle
. Displace and reposition the door handle release cable
. Displace and remove the door lock assembly.
. Position the new door lock assembly to the door.
. Position and fit door handle release cable to abutments.
. Fit and fully seat the cable retaining edge clip.
. Fit and tighten the door lock assembly securing bolts.
. Reposition glass frame. Fit and tighten frame securing
. Connect the multi-plug and fit to the mounting bracket.
. Connect the key barrel link rod.
. Connect the door sill button link rod.
. Connect the door handle link rod.
. Reposition the weathershield to the door. Using a suitable
tool, apply pressure to the weathershield edge to ensure
adhesion to the door.
plug
from the mounting bracket and disconnect.
the glass frame.
(6 Fig. 1 ).
release cable (8 Fig. 1).
from the abutments.
bolt.
. Refit the lower trim pad, upper trim pad and the veneer
0 trim pad.
I I J86-1923
Fig. 1
Issue 1 August 1994 X300 VSM 43

Security System - RESTRICTED ISSUE 84
-
A5.18 REAR DOOR LOCKASS€MBLY - RENEW
SRO 86.25.47
. Remove the veneer trim pad. See Section 13 of the VSM.
. Remove the upper trim pad. See Section 13 of the VSM.
. Remove the lower trim pad. See Section 13 of the VSM.
. Using a suitable plastic knife, cut through the weathershield to door sealant and pull back the weathershield for ac-
. Cut and remove the securing tie-wrap from the door lock assembly harness multi-plug.
Displace and reposition the door lock assembly multi-plug from the mounting bracket and disconnect.
Disconnect the door handle link rod.
. Disconnect and remove the door sill button link rod.
= Undo and remove the door lock assembly securing bolts.
. Undo and remove the lower securing bolt from the glass frame.
Displace and reposition the door lock assembly into the bottom of the door.
Displace and remove the edge clip from the door handle release cable.
. Displace and reposition the door handle release cable.
9 Displace and remove the door lock assembly.
cess
to the door lock assembly.
A5.19 TRUNKLIDLOCKACTUATOR- RENEW
SRO 86.25.49
. Open the trunk lid.
. Remove the luggage compartment lamp assembly. See Section 15 of the VSM.
Displace and remove the trunk lid liner fasteners and reposition for access.
. Undo and remove actuator mounting bracket securing bolts.
Disconnect the actuator to lock mechanism link rod.
. Remove the actuator and motor.
Undo and remove the actuator to mounting bracket securing screws.
Fitting
a new actuator is the reverse of the removal procedure.
Disconnect
the actuator harness
multi-plug.
15.20 CLOCKMODULE- RENEW
SRO 86.80.13
. Remove centre console ashtray and veneer panel., refer to VSM, section 13.
. Release and remove gear selector illumination module securing screws.
. Re-position illumination module as necessary for removal of radio console.
= Release radio console securing screws, partially withdraw radio console from center console so that console harness
and radio aerial connectors can be removed.
. Release radio ground lead from securing nut.
. Remove dedicated radio harness connector from multi-plug.
. Fully withdraw radio console and remove radio unit.
Release securing screws and remove clock module.
15.21 READER EXCITER COIL AND MODULE - RENW
. Access to the reader exciter coil is gained by removing top and bottom ignition cowls, refer to VSM, Section 13 for
The exciter coil is mounted around the ignition switch and can be removed by releasing spring tension coil clips.
. The module is mounted on the steering column assembly, secured by two bolts.
. To remove the module disconnect the harness multi-plug and remove the securing bolts.
remove
/ refit instructions.
X300 VSM Issue 1 August 1994 44