engine JEEP CHEROKEE 1988 Service Workshop Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 1988, Model line: CHEROKEE, Model: JEEP CHEROKEE 1988Pages: 1378, PDF Size: 19.9 MB
Page 89 of 1378
Fig. 12: Cherokee Engine Control System Wiring Diagram
Page 91 of 1378
![JEEP CHEROKEE 1988 Service Workshop Manual \
\
\
\
\
\
\
ABBREVIATION DEFINITION](/img/16/57037/w960_57037-90.png "JEEP CHEROKEE 1988 Service Workshop Manual \
\
\
\
\
\
\
ABBREVIATION DEFINITION")
\
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
B/P Backpressure
BAC By-Pass Air Control
BAP Barometric Absolute Pressure Sensor
BARO Barometric
BBDC Before Bottom Dead Center
BCM Body Control Module
BDC Bottom Dead Center
BHP Brake Horsepower
BLK Black
BLU Blue
BMAP Barometric & Manifold Absolute Pressure Sensor
BOO Brake On-Off Switch
BP Barometric Pressure sensor
BPS Barometric Pressure Sensor
BPT Backpressure Transducer
BRN Brown
BTDC Before Top Dead Center
BTU British Thermal Unit
BVSV Bimetallic Vacuum Switching Valve
Baro. Barometric
Batt. Battery
Bbl. Barrel (Example: 4-Bbl.)
Blst. Ballast
Blwr. Blower
Brkr. Breaker
\
\
\
\
\
\
\
\f
"C" ABBREVIATION TABLE
"C" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
C Celsius (Degrees)
C(3) I Computer Controlled Coil Ignition
C(4) Computer Controlled Catalytic Converter
CANP Canister Purge solenoid
CARB California Air Resources Board
CAT Catalytic Converter
CB Circuit Breaker
CBD Closed Bowl Distributor
CBVV Carburetor Bowl Vent Valve
cc Cubic Centimeter
CCC Computer Command Control
CCD Computer Controlled Dwell
CCM Central Control Module
CCO Converter Clutch Override
CCOT Cycling Clutch Orifice Tube
CCW Counterclockwise
CDI Capacitor Discharge Ignition
CEC Computerized Engine Control
CFI Central Fuel Injection
CID Cubic Inch Displacement
CID Cylinder Identification sensor
CIS Continuous Injection System
CIS-E Continuous Injection System-Electronic
CKT Circuit
CLR Clear
CNG Compressed Natural Gas
Page 93 of 1378
![JEEP CHEROKEE 1988 Service Workshop Manual \
\b\
\
\
\
\
\
EAC Electric Assist Choke](/img/16/57037/w960_57037-92.png "JEEP CHEROKEE 1988 Service Workshop Manual \
\b\
\
\
\
\
\
EAC Electric Assist Choke")
\
\b\
\
\
\
\
\
EAC Electric Assist Choke
EACV Electric Air Control Valve
EBCM Electronic Brake Control Module
ECA Electronic Control Assembly
ECAT Electronically Controlled Automatic Transaxle
ECM Electronic Control Module
ECT Engine Coolant Temperature Sensor
ECU Electronic Control Unit or Engine Control Unit
EDF Electric Drive Fan relay assembly
EDIS Electronic Distributorless Ignition System
EEC Electronic Engine Control
EECS Evaporative Emission Control System
EEPROM Electronically Erasable PROM
EFE Early Fuel Evaporation
EFI Electronic Fuel Injection
EGO Exhaust Gas Oxygen sensor (see HEGO)
EGR Exhaust Gas Recirculation system
EGRC EGR Control solenoid or system
EGRV EGR Vent solenoid or system
EMR Emission Maintenance Reminder Module
ESA Electronic Spark Advance
ESC Electronic Spark Control
EST Electronic Spark Timing
ETR Emergency Tensioning Retractor
EVAP Fuel Evaporative System
EVIC Electronic Vehicle Information Center
EVO Electronic Variable Orifice
EVP EGR Valve Position Sensor
EVR EGR Valve Regulator
EVRV Electronic Vacuum Regulator Valve
Elect. Electronic
Eng. Engine
Evap. Evaporative
Exc. Except
\
\
\
\
\
\
\
\f
"F" ABBREVIATION TABLE
"F" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
F Fahrenheit (Degrees)
F/B Fuse Block
FBC Feedback Carburetor
FI Fuel Injector or Fuel Injection
FICD Fast Idle Control Device
FIPL Fuel Injector Pump Lever
FP Fuel Pump
FPM Fuel Pump Monitor
FPR-VSV Fuel Pressure Regulator Vacuum Switching Valve
FWD Front Wheel Drive
Fed. Federal
Ft. Lbs. Foot Pounds
\
\
\
\
\
\
\
\f
"G" ABBREVIATION TABLE
"G" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
Page 95 of 1378
Ign. Ignition
In. Inches
Inj. Injector
\
\
\
\
\
\
\
\f
"J" ABBREVIATION TABLE
"J" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
J/B Junction Block
\
\
\
\
\
\
\
\f
"K" ABBREVIATION TABLE
"K" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
k/ohms 1000 ohms (kilo as in k/ohms)
kg Kilograms (weight)
kg/cm Kilograms Per Square Centimeter
KAM Keep Alive Memory
KAPWR Keep Alive Power
KM/H Kilometers Per Hour
KOEO Key On Engine Off
KOER Key On Engine Running
KS Knock Sensor
\
\
\
\
\
\
\
\f
"L" ABBREVIATION TABLE
"L" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
L Liter(s)
L/D Light Duty
LCD Liquid Crystal Display
LED Light Emitting Diode
LH Left Hand
LOS Limited Operation Strategy
LT BLU Light Blue
LT GRN Light Green
LUS Lock-Up Solenoid
Lbs. Pounds
Lt(s). Light(s)
Lugg. Luggage
\
\
\
\
\
\
\
\f
"M" ABBREVIATION TABLE
"M" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
mA Milliamps
mV Millivolts
mfd. Microfarads
Page 98 of 1378
RVB Rear Vacuum Break
RWAL Rear Wheel Anti-Lock Brake
RWD Rear Wheel Drive
Recirc. Recirculate or Recirculation
Reg. Regulator
Rly. Relay
\
\
\
\
\
\
\
\f
"S" ABBREVIATION TABLE
"S" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
SAW Spark Angle Word
SBC Single Bed Converter
SBEC Single Board Engine Controller
SC Super Charged
SCC Spark Control Computer
SCS Air Suction Control Solenoid
SDM Supplemental Restraint System Diagnostic Module
SDU SRS Diagnostic Unit
SEN Sensor
SES Service Engine Soon
SFI Sequential (Port) Fuel Injection
SIG RTN Signal Return circuit
SIL Shift Indicator Light
SIR Supplemental Inflatable Restraint
SMEC Single Module Engine Controller
SOHC Single Overhead Cam
SOL or Sol. Solenoid
SPFI Sequential Port Fuel Injection
SPK Spark Control
SPOUT Spark Output Signal
SRS Supplemental Restraint System (Air Bag)
SS 3/4-4/3 Shift Solenoid circuit
SSI Solid State Ignition
STAR Self-Test Automatic Readout
STI Self Test Input circuit
STO Self-Test Output
SUB-O2 Sub Oxygen Sensor
Sen. or Sens. Sensor
Sol. Solenoid
Sprchg. Supercharger
Strg. Steering
Susp. Suspension
Sw. Switch
Sys. System
\
\
\
\
\
\
\
\f
"T" ABBREVIATION TABLE
"T" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
T.V. Throttle Valve
TAB Thermactor Air By-Pass
TAC Thermostatic Air Cleaner
TAD Thermactor Air Diverter
TAN Tan
TBI Throttle Body Injection
Page 101 of 1378
\003
A/C C O M PR ESSO R O IL C HEC KIN G
1988 J e ep C hero ke e
A/C General Servicing
COMPRESSOR OIL CHECK
* PLEASE READ THIS FIRST *
CAUTION: When discharging air conditioning system, use only approved
refrigerant recovery/recycling equipment. Make every attempt
to avoid discharging refrigerant into the atmosphere.
ISOLATING COMPRESSOR - GRAND WAGONEER ONLY
1) Connect service gauge set to the compressor service valves
and open compressor valves slightly (turn clockwise). Start engine and\
operate air conditioning. Slowly turn compressor suction valve
clockwise toward closed (front-seated) position.
2) When suction pressure is reduced to zero or less, turn off
engine and compressor and quickly turn suction valve stem in to full
front-seated position. Suction pressure should be slightly above zero.
Turn discharge valve into front-seated position.
3) To check oil lever, slowly open crankcase plug to relieve
any remaining pressure. After oil level is correct, cap service gauge
parts on both valves. Back-seat suction service valve to allow
refrigerant to enter compressor. Open discharge valve halfway.
4) Loosen discharge service valve cap, allowing refrigerant
pressure to force air out of compressor. Back-seat service valve and
tighten cap. Compressor is now ready for operation.
REFRIGERANT OIL
Only new, pure, moisture-free refrigerant oil should be used
in the air conditioning system. This oil is highly refined and
dehydrated to a point where moisture content is less than 10 parts per
million. The oil container must be tightly closed at all times when
not in use, or moisture will be absorbed from the air and introduced
into the refrigeration system.
DISCHARGING SYSTEM
CAUTION: When discharging air conditioning system, use only approved
refrigerant recovery/recycling equipment. Make every attempt
to avoid discharging refrigerant into the atmosphere.
If compressor has stem-type service valves, it can be
isolated and removed without discharging entire system. Otherwise,
discharge system completely using approved refrigerant
recovery/recycling equipment before loosening any fittings.
DISCONNECTING LINES & FITTINGS
After system is discharged, carefully clean area around all
fittings to be opened. Always use 2 wrenches when tightening or
loosening fittings to avoid twisting or distorting lines. Cap or plug
all openings as soon as lines are removed. Do not remove caps until
immediately before connections are made. This will keep entry of air
and moisture to a minimum, reducing the chance of damage to
components.
Page 105 of 1378
of the scale, a symbol for defroster indicates defrost position. In
"BI-LEVEL" position, a mixture of floor heat and defroster air is
obtained.
The lower temperature control lever operates blend-air door
in heater core housing. At full right position, all air is directed
through heater core, providing maximum heat flow. At full left
position, all air is directed around heater core providing fresh air.
Control can be set in any intermediate position to provide a blend of
heated and unheated air. Heater must be in heat or defrost mode before
any air can enter vehicle.
TROUBLE SHOOTING
See JEEP TROUBLE SHOOTING at the end of this article.
REMOVAL & INSTALLATION
CONDENSER
Removal (Cherokee, Comanche & Wagoneer) NOTE: On these
models, condenser and receiver-drier are replaced
as a unit.
1) Drain radiator. Disconnect fan shroud and radiator hoses.
Disconnect automatic transmission cooler lines (if equipped).
Discharge A/C system using approved refrigerant recovery/recycling
equipment.
2) Disconnect A/C hoses from condenser. Unplug low pressure
switch. Remove radiator and condenser as an assembly. Detach condenser
retaining bolts. Separate condenser from radiator. Remove receiver-
drier from condenser.
NOTE: Plug receiver-drier openings whenever unit is removed from
condenser. Add 1 oz. of refrigerant oil (AMC No. 8132400) to
system when replacing condenser.
Installation
To install, reverse removal procedure. Fill radiator.
Evacuate, leak test, recharge and check A/C system operation.
Removal (Wrangler)
1) Discharge system (slowly to prevent loss of compressor
oil) using approved refrigerant recovery/recycling equipment. Drain
coolant. Remove fan shroud and radiator. Disconnect pressure line at
condenser. Remove condenser mounting screws. Tilt bottom of condenser
toward engine.
2) From underside of vehicle, disconnect hose attaching
receiver-drier to evaporator. Plug all openings to prevent entry of
dirt or moisture. Remove receiver-drier and condenser assembly. Remove
receiver-drier from condenser.
Installation
To install, reverse removal procedure. Fill radiator.
Evacuate, leak test, recharge and check A/C system operation.
RECEIVER-DRIER
NOTE: On Cherokee, Comanche and Wagoneer, receiver-drier is
removed with condenser and radiator as an assembly.
Removal (Wrangler)
Page 107 of 1378
housing attaching nuts from studs on engine compartment side of dash
panel. Remove evaporator drain tube.
4) Remove right kick panel. Detach instrument panel support
bolt. Gently pull on right side of dash, then rotate housing downward
and toward rear of vehicle to disengage housing studs from dash panel.
Remove evaporator-blower housing.
5) To remove heater core, detach retaining screws. Remove
heater core by pulling straight out of housing. To remove evaporator
core, detach top housing retaining screws, then remove top of
evaporator housing.
6) Remove thermostatic switch and capillary tube. Detach 2
evaporator retaining screws and lift evaporator core from housing.
Remove expansion valve from evaporator.
Installation
1) To install components, reverse removal procedure. When
installing evaporator core, install thermostatic switch and capillary
tube before installing top of housing.
2) When installing heater core, ensure seal is properly
cemented in place to prevent it from moving when blower assembly is
installed. Evacuate, leak test, recharge and check A/C system
operation.
NOTE: The evaporator housing mounting location is similar to
Wrangler, except blower motor is mounted horizontally to
firewall.
Removal (Wrangler)
1) Discharge system using approved refrigerant
recovery/recycling equipment. Disconnect inlet line at compressor.
Disconnect hose, at quick-disconnect coupling, between receiver-drier
and evaporator. Remove hose clamps and dash grommet retaining screws.
See Fig. 2 .
Fig. 2: Wrangler Evaporator Housing Mounting Screw Locations
Courtesy of Chrysler Motors.
NOTE: It is not necessary to discharge system to service blower
motor. Evaporator housing may be lowered from instrument
Page 115 of 1378
System Charge Test
1) To check system refrigerant level, a sight glass has been
incorporated into the receiver-to-evaporator hose at the receiver end.
A continuous stream of bubbles will appear in the sight glass of a
system that is not properly charged. However, both properly charged
systems and discharged systems will appear the same because of a lack
of bubbles.
2) To test for discharge condition, cycle the clutch off and
on with engine at 1500 RPM. When clutch is off, bubbles will appear if
there is refrigerant in the system. If no bubbles appear, system is
discharged. If discharged, leak test, repair and recharge system.
A/C SYSTEM OPERATION CHART & VACUUM DIAGRAM
A/C SYSTEM OPERATION TABLE \
\
\
\
\
\
\
MODE
LEVER BLOWER PANEL FLOOR DEFROST WATER
POSITION AIR DISCHARGE SPEEDS DOOR DOOR DOOR VALVE
\
\f\
\f\
\f\
\f\
\f\
\f\
Off(
1)( 2) Closed None Open ( 3) Closed Closed
\
\f\
\f\
\f\
\f\
\f\
\f\
Max A/C Panel Regis- 4
(
1)( 4) ters With Open Bleed Closed Open( 5)
Floor Bleed
\
\f\
\f\
\f\
\f\
\f\
\f\
Norm A/C Panel Regis- 4(
6) Open Bleed Closed Open( 5)
(
7)( 4) ters With
Floor Bleed
\
\f\
\f\
\f\
\f\
\f\
\f\
Bi-Level Panel 4(
6) Open Open Bleed Open( 1)
(
7)( 4) Registers
and Floor
With Def.
Bleed
\
\f\
\f\
\f\
\f\
\f\
\f\
Vent Panel 4 Open Bleed Closed Closed
(
7)( 2) Registers
With Floor
Bleed
\
\f\
\f\
\f\
\f\
\f\
\f\
Heat Floor With 4 Closed Open Bleed Open(
1)
(
7)( 2) Def. Bleed
\
\f\
\f\
\f\
\f\
\f\
\f\
Def. Defroster 4 Closed Bleed Open Open(
1)
(
7)( 2) With Floor
Bleed
\
\
\
\
\
\
\
(
1) - Recirculating Door is in Recirc. position.
(
2) - Indeterminate
(
3) - A/C Compressor is OFF
(
4) - A/C Compressor is ON
(
5) - Water valve closes in full "COOL" temperature lever position.
(
6) - Speeds are reduced by approximately 2.0 Volts.
(
7) - Recirculating Door is in Outside position.
\
\
\
\
\
\
\
\b
Page 118 of 1378
HEATER HOSES
HIGH PRESSURE RELIEF VALVES (HPRV)
IDLERS
IN-LINE FILTERS
METAL FITTINGS
METAL LINES
MIX AND AIR CONTROL DOORS (BLEND DOORS)
O-RINGS
ORIFICE TUBES
PILOT-OPERATED ABSOLUTES (POAS)
PLENUMS
PRESSURE CONTROL VALVES
PRESSURE SENSORS
PULLEYS
RADIATORS
RECEIVER-DRIERS
REFRIGERANT
REFRIGERANT OIL
RELAYS
SEALS
SERVICE PORTS
SPRING LOCK COUPLINGS
SUCTION THROTTLING VALVES (STVS)
SWITCHES (ELECTRICAL)
TENSIONERS
THERMISTORS AND PRESSURE SENSORS
THERMOSTATS AND HOUSINGS
VACUUM HOSES AND TUBES
VACUUM RESERVOIRS
VACUUM TUBES
VALVES IN RECEIVER (VIRS)
WATER PUMPS (ELECTRIC AUXILIARY)
WIRING HARNESSES AND CONNECTORS
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards