ABS JEEP CJ 1953 Owner's Manual

M
FRONT
AXLE
1— Nut
2—
Lock
Washer

3—
Bearing
Lock
Washer
4—
Wheel
Bearing Cup 5—
Cone
and Rollers
6—
Oil
Seal 7— Spindle
8— Spindle Bushing
9—
Filler
Plug
10—
Right
Knuckle and Arm
11— Shims
12— Pivot Pin
13—
Lock
Washer
14—
Cap
Screw
15— Nut
16—
Washer

17—
Universal
Joint Yoke
18—
Oil
Seal
19—
Oil
Slinger
FIG.
M-2—FRONT
AXLE

20—
Cone
and Rollers
21—
Bearing
Cup
22—
Right
Axle Shaft with Universal Joint
23—
Knuckle
Oil Seal Retainer
24— Housing Breather 25—
Front
Axle Housing
26—
Axle
Shaft with Universal Joint
27—
Oil
Seal
28—
Axle
Shaft Guide
29—
Shim
Pack
30—
Bearing
Cup
31—
Cone
and Rollers
32—
Ring
Gear
and Pinion
33—
Thrust
Washer

34—
Thrust
Washer

35—
Differential
Gears
36— Housing Cover Gasket
37— Housing Cover
38—
Fill
Plug 39—
Screw
and
Lock
Washer
40—
Bearing
Cup
41—
Cone
and Rollers
42— Shims
43—
Lock
Pin
44—
Pinion
Shaft
45—
Differential
Case
47— Bolts
48— Nut
49—
Oil
Seal and Backing Ring
50—
Thrust
Washer
51— Snap Ring
52— Stop Bolt
53— Nut 54—
Bearing
Cup
55—
Cone
and Rollers
56—
Gasket

checked, making sure it is clean and open.

The
front wheel bearings should be checked every
12,000
miles. Refer to Section Q. Front wheel toe-

in
is adjustable by lengthening or shortening the
tie rod. However, standard caster and camber of
the front
wheels
are built
into
the axle. Wheel
caster can be adjusted by placing tapered shim
plates or
wedges
between
the springs and spring

seats
welded to the axle housing. Steering
geometry

and
front wheel adjustments are discussed in Sec­ tion O.

The
axle housing should be checked periodically
for weld cracks and/or other damage that may cause misalignment of the front
wheels
or
loss

of lubricant. The spring clips (U-bolts) should be
inspected and torqued every
12,000
miles. Torque (spring clip) nuts 45 to 50 lb-ft. [6,2 a 6,9 kg-m.].

M-4. FRONT
AXLE
REMOVAL
a.
Raise front end of vehicle
arid
safely support the frame by placing stands under the frame at
the rear of the front spring rear hangers.
b. Place
jack
under front axle housing and relieve
axle
weight
from the springs.
c. Disconnect shock absorbers from spring clip plates.
FIG.
M-3—HUB
CAP
PULLER

d.
Disconnect steering link from tie rod socket-
joint assembly.
e. Disconnect hydraulic brake
hoses
from front

brake
lines. Disconnect
hoses
from frame brackets. 278

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

M
FIG.
M-12—FRONT
AXLE—EARLY
MODEL
DJ-5, DJ-6
1— Outer Bearing Cone and Rollers
2— Outer Bearing Race
3—
Inner
Bearing Cone and Rollers
4—
Inner
Bearing Race 5— -Wheel Brake Cylinder
6— Bleeder Screw 7— Upper Expansion Plug
8— Steering Knuckle Pin
9— Steering Knuckle Bushing
10—
Lubrication
Fitting Opening
11—
Front
Axle I-Beam 12— Steering Knuckle Pin Bearing 13—
Brake
Backing Plate
14—
Brake
Drum 15—
Brake
Shoe

16— Wheel Hub Bolt
17— Spindle
18—
Front
Wheel Hub
19— Spindle Nut
d. Disconnect the shock absorbers at the axle

mounting
pads.
e. Disconnect the brake hydraulic
hoses
at the
connections
between
front brake
lines
and
flexible
hoses.

f. Support the axle assembly on a jack, ready for removal. g. On
vehicles
with the springs slung over the axle,

remove
the
nuts
from the spring to axle U-bolt clips,

remove
the spring clip
plates,
and slide the axle as­

sembly
from underneath the vehicle.

On
vehicles
with the springs slung under the axle,
remove
the
nuts
from the spring clips and
remove

the spring clip
plates.
Then
disconnect
the spring

FIG.
M-13—FRONT
AXLE, LATE
MODEL
DJ-5, DJ-6
1— Steering Knuckle
2— Steering Knuckle Bushing
3—
Key

4— Steering Arm
5—
Lock
Spring
6—
Oil
Seal Retainer 7—
Oil
Seal
8—
Tapered
Pin
9— Dust Cover
10— Nut
11— Cotter Pin
12— Tie
Rod
13— Axle Tube 14— Plug
15— Steering Knuckle Pin
16—
Shim

17—
Thrust
Bearing
18— Bolt
19— Nut 20— Nut
21— Cotter Pin 11660
283

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

M
M-19.
SERVICE
DIAGNOSIS

SYMPTOMS
PROBABLE
REMEDY

Hard Steering
Lack
of
Lubrication
Lubricate
Tires
Soft.
. Inflate

Tight
Steering. Adjust. See "Steering" Section

Low Speed Shimmy
or
Wheel Fight
Spring
Clips and Shackles Loose
Front
Axle Shifted Insufficient Toe-In

Improper
Caster
Steering System Loose or Worn
Twisted Axle

High Speed Shimmy
or
Wheel Fight
Check
Conditions Under "Low Speed Shimmy"

Tire
Pressures Low or not
Equal

Wheel Out of Balance
Wheel Runout
Radial
Runout of Tires
Wheel Camber
Front
Springs
Settled
or Broken
Bent Steering Knuckle
Arm..................

Shock Absorbers not Effective
Steering
Gear
Loose on Frame

Front
Springs too Flexible

Tramp
Wheels Unbalanced

Wandering
Improper
Toe-in

Broken
Front Spring Main
Leaf

Axle Shifted Loose Spring Shackles or Clips
Improper
Caster

Tire
Pressure Uneven
Tightness in Steering System
Loose Wheel Bearings
Front
Spring
Settled
or Broken
Axle
Noisy
on
Pull
Pinion and Ring
Gear
Adjusted too Tight
Pinion Bearings Rough.

Axle Noisy
on
Coast
Excessive Back
Lash
at Ring and Pinion Gears.

End
Play in Pinion Shaft. . . Rough Bearing.

Axle Noisy
on
Coast
and
Pull
Ring
and Pinion Adjusted too Tight
Pinion Set too
Deep
in Ring
Gear
Pinion Bearing Loose or Worn

Back Lash
Axle Shaft Universal Joint Worn
Axle Shaft Improperly Adjusted

Worn
Differential Pinion Washers
Worn
Propeller Shaft Universal Joints.
Readjust
or Replace

Broken
Spring Center Bolt

Adjust
Reset

Adjust
or Overhaul Steering
Gear,
Front Axle or
Steering Parts
Straighten or Adjust
Inflate
Balance
Straighten Mount Properly
Same on Both Wheels
Repair
or Replace
Straighten or Replace
Replace or Repair Tighten

Over
Lubricated

Check
and Balance

Adjust—Check
for Bent Steering Knuckle Arm Replace

Spring
Center Bolt Broken
Adjust
or Replace
Reset Inflate

Adjust
Adjust
Repair
or Replace

Readjust

Replace

Readjust
Readjust

Replace

Readjust Readjust
Readjust
or Replace
Replace
Readjust

Replace

Repair

Emergency
Where difficulty is experienced with front axle differential making the vehicle inoperative,

remove
axle driving
flanges.
This will allow bringing vehicle in under its own power. Be sure the transfer
case
shift lever is in the neutral
(disengaged)
position.
285

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

N

FIG.
N-l6—AXLE
SHAFT
BEARING
INSTALLED
1—
Retainer
Ring

2—
Unit
Bearing

3—
Seal

4—
Retainer
Plate
5—
Axle
Shaft
Flange
N-9.
REAR
AXLE
ASSEMBLY

The
following
paragraphs
(Pars.
N-9 through N-19)
describe the removal, disassembly, assembly and
services performed on
rear
axle assemblies having
conventional differentials.
Pars.
N-20 through N-32 describe the services to be performed on
rear
axle
assemblies having
Powr-Lok
and
Trac-Lok
dif­
ferentials.

Note:
The
full
floating front axle differential as­
sembly is similar to the
rear
axle differential and is
removed, inspected, disassembled, and assembled
in
the same manner as the
rear
axle differential
covered in this section.
FIG.
N-l
7—OIL
SEAL
DRIVER

Note:
The pinion shaft oil seal is serviced in the
vehicle when replacement is necessary. Refer to

Fig.
N-l8.
11851
j

J

FIG.
N-l8—REMOVING
PINION
SHAFT
OIL
SEAL

1—Tool
W-251 N-10. Inspection

Refer
to Fig. N-3 and N-7. Before disassembling the differential, it is advisable
to determine through inspection the cause of the

failure.
Inspection procedure is as follows:

a.
Drain
lubricant and remove housing cover and gasket.

b.
Clean
the differential parts thoroughly with sol­
vent.

c.
Carefully
inspect all parts.

Should
it be determined by inspection that the

differential
requires overhauling, the axle must first
be removed from the vehicle.

Note:
All service replacement axle assemblies are
shipped from the factory without lubricant in the

differential.
Lubricant
must be added to the dif­

ferential
before
the axles are installed in vehicles.

Use
the grade and quantity of lubricant specified
in
the
Lubrication
Chart.

After
the axle has
been
installed in the vehicle,
check
to be sure the lubricant level in the differen­

tial
is up to the filler plug opening.

N-l
1.
Rear
Axle Removal

To
remove the
rear
axle, proceed as follows:
a.
Raise the
rear
of the vehicle with a hoist. Safely
support the frame ahead of the
rear
springs.

b.
Remove the wheels.

c.
Disconnect the propeller shaft at the
rear
yoke.

d.
Disconnect the shock absorbers at the axle
mounting.
e. Disconnect the brake hydraulic
hose
at the tee
fitting on the axle just
below
the
left
frame side
rail.
Tape
ends
of
hose
to
keep
out
dirt.

f. Disconnect the parking brake cable at the frame
mounting. DJ
models
only.
g. Support the axle housing on a
jack.

h.
Remove the axle U-bolts.
i.
Slide the axle from under the vehicle. 293

m

REAR AXLE
c. Attach the brake line
hose
at tee fitting on top
of housing.

d.
Attach parking brake cables at rear of brake
backing plate. DJ
models
only.
e. Connect the shock absorbers at the axle mount­
ing pads.
f. Connect the propeller shaft at the rear universal
joint.
g. Adjust and bleed brakes. (See Section P).

h.
Install
wheels
and lower vehicle to floor.
i.
Check parking brake as described in Section P.

j.
Fill
the axle housing with the proper lubricant.

For
correct lubricant refer to the
Lubrication
Chart.

N-34.
TROUBLE
SHOOTING

The
following problems can be present with either the conventional differential,
Powr-Lok
or
Trac-
Lok
differential.
N-35. Backlash

Excessive
backlash in the vehicle drive line may be the results of
excessive
backlash in the trans­
mission, propeller shaft spline, universal joint, ring gear and pinion, the axle shaft spline, or the dif­
ferential.
Excessive
backlash in the differential may be meas­

ured
as follows:
a.
Jack
up one rear wheel.
b. Put the transmission in gear.
c. Measure the travel of the jacked-up wheel on
a
10"
[25,40
cm.] radius from the wheel center.

This
total
movement
should not
exceed
IVi" [3,17 cm.] in a new unit. In order to restrict the

backlash
to the axles only, make sure that the
yoke of the propeller shaft
does
not
move
during
the check.

d.
If all causes of backlash mentioned
above
have

been
eliminated with the exception of the differen­

tial
and that still
exceeds
the maximum allowable
movement, overhaul the differential.
N-36.
Rear
Wheel
Noise

Looseness of the rear axle shaft nut on semifloat- ing tapered rear axles may produce a clicking or
creaking
noise.
This
noise
can usually be
stopped

by torquing the wheel hub nut 150 to 175 lb-ft. [20,7 a 24,2 kg-m.]. If the condition has continued
for
some
time, slight wear may have resulted allow­
ing the
noise
to persist. In this case, coat the hub,
key, and keyway on tapered axle shafts with white
lead and torque the nut as specified. If the
noise
persists after this treatment, replace the worn parts.

N-37.
SERVICE DIAGNOSIS

SYMPTOMS

Axle
Noisy on Pull and
Coast
Excessive
Back
Lash
Bevel
Gear
and Pinion. . . . . Adjust

End
Play Pinion Shaft Adjust

Worn
Pinion Shaft Bearing Adjust
Pinion
Set too Deep in Bevel
Gear
too Tight..... Adjust

Wrong
Lubricant
Being Used
(Powr-Lok
or
Trac-Lok
Differential) . Replace

Axle
Noisy on
Pull
Pinion
and Bevel
Gear
Improperly Adjusted Adjust

Pinion
Bearings Rough....................... Adjust

Pinion
Bearings Loose Adjust

Axle
Noisy on Coast
Excessive
Back
Lash
in Bevel
Gear
and Pinion. . . Adjust

End
Play in Pinion Shaft. . Adjust

Improper
Tooth Contact.
....................
Adjust
Rough Bearings Replace

Back
Lash
Worn
Differential Pinion
Gear
Washers Adjust
Excessive
Back
Lash
in Bevel
Gear
and Pinion. . . Adjust

Worn
Universal Joints Replace
PROBABLE REMEDY

310

'Jeep'
UNIVERSAL
SERIES SERVICE
MANUAL

O Note:
If the steering-gear-to-frame
bolts
are not

properly
torqued, they
will
eventually
loosen
dur­

ing operation of the vehicle. Loose
bolts
will
result
in
elongated
bolt
holes
making maintenance of bolt torque difficult, and may allow position of the
steering columns to be misaligned. Therefore,
proper
torquing is extremely important.
Do not tighten the steering gear to dampen out
steering trouble. Adjust the steering gear only to
remove lost motion or play within the unit.
0-5. Steering
Gear
Adjustment
The
cam and lever steering gear is illustrated in

Fig.
0-2. It consists of a
spiral
cam, and a cross shaft and lever assembly with two lever studs.
When
the steering wheel is turned, the cam
moves

the studs, causing rotary movement of the cross
shaft, which in
turn
causes angular movement of
the*steering arm.

Two
adjustments of the steering gear are necessary:
up and down play of the steering shaft, and adjust­ment of the lever studs (tapered pins) in the

cam
groove.

Adjustment
of the
ball
thrust bearings to eliminate up and down play of the steering shaft is ac­
complished by removing shims which are installed
between
the steering gear housing and the upper
cover. Before making this adjustment
loosen
the
housing side cover adjusting screw to free the pins
in
the cam groove. Loosen the housing cover to
cut and remove a shim or more as required.
Install
the screws and tighten. Adjustment should be
made to have a slight drag but allow the steering
wheel to
turn
freely with thumb and forefinger
lightly gripping the rim.

Shims
installed for adjustment are .002*, .003", and .010"
[.0508,
.0762
and .254 mm.] in thickness.

Adjustment
of the tapered pins in the cam
groove

is accomplished by adjusting screw. Unlock the

adjusting
screw and
turn
it in until a very slight
drag
is felt through the mid-position when turning
the steering wheel slowly from one extreme position
to the other.

Backlash
of the pins in the
groove
shows up as
end play of lever shaft, also as backlash of steer­ ing arm.

The
cam
groove
is purposely cut shallow in the

straight
ahead driving position for each pin.
This

feature permits a
close
adjustment for normal

straight
ahead driving and provides precision steer­ ing and permits take up of backlash at this point
after the wear occurs without causing a bind else­

where.
Always
adjust within the high range through
the mid-position of pin travel. Do not adjust off
"straight
ahead" position.
Backlash
in turned posi­
tions is not objectionable.
0-6.
Front
Wheel Alignment Adjustments
To
ensure correct alignment, a definite procedure
for inspection of the steering system is recom­ mended. It is
suggested
that the following sequence
be used:

a.
Equalize
tire pressures and level vehicle.
b.
Check
steering gear to steering column align­
ment.

c.
Inspect steering knuckle pivots, spindle, and
wheel bearing
looseness.

d.
Check
wheel runout.

e.
Test wheel balance and bearing adjustment.
f.
Check
for spring sag.
g.
Inspect brakes and shock absorbers.

h.
Check
steering gear assembly adjustment and
steering connecting rod.

i.
Check
caster,

j.
Check
toe-in.
k.
Check
toe-out
on turns.

I.
Check
camber.

m.
Check
tracking of front and
rear
wheels,

n.
Check
frame alignment.

The
factors of alignment, caster, camber, and toe-
in,
are all interrelated and if one adjustment is
made, another adjustment may be affected.
There­

fore, after an alignment job is completed, make a
complete recheck of all the adjustments to be sure
the
settings
are within the limit. Be sure all front
suspension and steering system nuts and
bolts
are

all
properly torqued before taking wheel alignment readings.

Proper
alignment of front wheels must be main­
tained in order to ensure
ease
of steering and satis­factory tire life.

The
most important factors of front wheel align­ment are wheel camber, axle caster and wheel
toe-in.

Wheel
toe-in is the distance the wheels are closer

together
at the front than at the
rear.
Wheel
camber is the amount the wheels incline out­

ward
at the top from a vertical position.
Front
axle caster is the amount in
degrees
that the
steering pivot pins are tilted towards the front or

rear
of the vehicle. Positive caster is inclination of
the top of the pivot pin towards the
rear
of the ve­

hicle.
Zero caster is the vertical position of the
pivot pin. Negative or reverse caster is the in­
clination
of the top of the pin towards the front
of the vehicle.

These
points should be checked at regular inter­
vals,
particularly when the front axle has been
subjected to a heavy impact. When checking wheel alignment, it is important that wheel bearings and

knuckle
bearings be in proper adjustment. Loose bearings
will
affect instrument readings when

checking
the camber, pivot pin inclination and
toe-in.
To
accurately check camber and caster, use a wheel
aligning fixture.
Camber
and caster of the front
wheels are both preset.
Camber
cannot be altered
but caster can be adjusted by installing caster shims
between
the axle pad and the springs. Wheel toe-in
may
be adjusted. To measure wheel toe-in, use a
wheel aligning fixture or follow the procedure given
in Par.
0-8.
0-7.
Front Wheel Toe-in
Toe-in
as illustrated in
Fig.
0-3, is necessary to
off­

set the
effect
of camber as shown in Fig. Q-4. 315

o
STEERING SYSTEM
FIG.
0-3—FRONT
WHEEL
TOE-IN
1—
Toe-in
Angle

2—
Vertical
Line
In
the absence of a wheel aligning fixture, toe-in

may
be set by measuring
between
the front wheels
at the
edge
of the rim, at the flange or at the tire
tread
center. When making this adjustment the
wheels must be in a straight ahead position.
It
is highly important that toe-in be checked regu­

larly
and if found to be out of adjustment, correc­ tion should be made immediately.

The
correct toe-in of
these
models is found in the
specifications at the end of this section.
0-8. Toe-in Adjustment
The
toe-in may be adjusted with a line or straight

edge
as the vehicle tread is the same in front and
rear.
To set the adjustment both tie rods must be
adjusted
as outlined below:
Set the tie rod end of the steering bell-crank at
right
angles with the front axle. Place a straight

edge
or line against the left
rear
wheel and left front wheel to determine if the wheel is in a straight

ahead
position. If the front wheel tire
does
not touch the straight
edge
at both the front and
rear,

it
will
be necessary to adjust the left tie rod by loosening the clamps on each end and turning the
rod
until the tire touches the straight
edge.

Check
the right hand side in the same manner, ad­

justing
the tie rod if necessary, making sure that the bell-crank remains at right angles to the axle.

When
it is determined that the front wheels are in the straight ahead position, set the toe-in by short­
ening each tie rod approximately one-half
turn.

0-9.
Front
Wheel
Camber
The
purpose of camber Fig. 0-4, is to more nearly
place the weight of the vehicle over the tire con­ tact on the road to facilitate
ease
of steering.

The
result of excessive camber is irregular wear of
tires on outside shoulders and is usually caused by
bent axle parts.

The
result of negative or reverse camber, if ex­
cessive,
will
be
hard
steering and possibly a wan­

dering
condition.
Tires
will
also wear on inside shoulders. Negative camber is usually caused by
excessive wear or
looseness
of front wheel bearings, axle parts or the result of a sagging axle.

Unequal
camber may cause any or a combination
of the following conditions: unstable steering, wan- 11894-

FIG.
0-4—WHEEL CAMBER

1—Vertical
Line
2—Camber Angle
dering,
kick-back or road shock, shimmy or exces­
sive tire wear. The cause of unequal camber is usu­
ally
a bent steering knuckle or axle end.
Correct
wheel camber is set in the axle at the time
of manufacture and cannot be altered by any ad­
justment. It is important that the camber be the same on both front wheels. Heating of any of
these
parts
to facilitate straightening usually destroys
the heat treatment given them at the factory.
Cold
bending may cause a fracture of the steel and is also
unsafe. Replacement with new parts is recom­ mended rather than any straightening of damaged

parts.

O-10.
Axle
Caster Caster
angle is established in the axle design by
tilting the top of the kingpin toward the
rear
and
the
bottom
of the kingpin forward so that an

imaginary
line through the center of the kingpin
would strike the ground at a point ahead of the point of tire contact.
FIG.
0-5—AXLE
CASTER

1—
Vertical
Line

2—
Caster
Angle
316

'Jeep'
UNIVERSAL SERIES SERVICE
MANUAL

The
purpose of caster Fig. O-S, is to provide steer­
ing stability which
will
keep the front wheels in the
straight
ahead position and also assist in straighten­
ing up the wheels when coming out of a
turn.
Caster
of the front wheels is preset. If the angle of

caster,
when accurately measured, is found to be

incorrect,
correct it to the specification given at
the end of this section by either installing new

parts
or installing caster shims
between
the axle

pad
and the springs.

If
the camber and toe-in are correct and it is known
the the axle is not twisted, a satisfactory check

may
be made by testing the vehicle on the road.
Before road testing, make sure all tires are properly

inflated,
being particularly careful that both front
tires are inflated to exactly the same pressure.
If
vehicle turns easily to either side but is
hard
to
straighten out, insufficient caster for easy handling of vehicle is indicated. If correction is necessary, it

can
usually be accomplished by installing shims

between
the springs and axle pads to secure the
desired
result.
0-11-
Front
Wheel
Turning
Angle
When
the front wheels are turned, the inside wheel
on the
turn
travels in a smaller circle than the out­side wheel, therefore, it is necessary for the wheels
to toe out to prevent the tire on the inside wheel

frOm
being scuffed sideways.
This
angle for toe out
on turns is designed to permit both front wheels to

turn
on a common center by having the ends of the
steering
knuckle
arms closer
together
than the king­

pins.

To
avoid possible damage to the universal joints
on the front axles of 4-wheel drive vehicles, it is advisable to check the turning angle.
Wearing
away
of the upset
edge
on the spindle housing bolt which
10607

FIG.
0-6—TURNING
ANGLE
STOP
SCREW
1—Stop
Screw
contacts the
stop
screw
will
increase the turning
angle to the point where the universal joints may
be damaged.

The
Jeep Universal Series vehicles should have a

turning
angle of not more than 27^° both left and

right.
To adjust the
stop
screw, it is necessary to

loosen
the locknut holding the
stop
screw. When
the adjustment has been made, tighten the locknut
on the screw to prevent any movement. Refer to
Fig.
O 6.

The
left steering knuckle arm controls the relation­
ship of the front wheels on a left
turn
and the right
arm
controls the relation on a right
turn.

0-12. Steering
Knuckle
Arm

Should
a steering knuckle arm
become
bent, the

knuckle
housing must be replaced. It is not safe to
straighten the knuckle arm.
0-13.
Front
Wheel
Shimmy
Wheel
shimmy may be caused by various condi­
tions in the wheels, axle or steering system, or a
combination of
these
conditions. Outlined below

will
be found the usual corrections of this fault:

a.
Equalize
tire pressures and see that they are
according
to specifications.

b.
Check
the wheel bearings for
looseness.
Be sure
that the inner wheel bearing race is not too
loose
on the spindle.

c.
Remove both steering knuckles and carefully inspect the upper and lower king pin bearings.

Inspect
the bearing cups for evidence of brinelling,
pitting, or fretting. Any bearings that show the slightest imperfection must be
replaced.
Reassemble

and
lubricate the front axle and steering linkage,
installing
new steering knuckle oil seals if present
seals show any wear.

d.
With
full
weight on the front wheels and one

man
working the steering play with the steering
wheel, a second man should closely observe the steering bell
crank
for any rocking motion and the
double tie rod socket for any rocking motion or

looseness
at both points. Replace the complete bell
crank
assembly if it has even the slightest rocking motion. The same applies to the double tie rod
socket.
e.
Check
wheel run-out.
This
check should include
radial
run-out and wheel
looseness
on the hub.
f- Test wheel balance—check for blowout patches,
uniform
tire tread, vulcanized tires, mud on inside
of wheels, and tires creeping on the
rims.

g.
Try
switching front wheels and tires to the
rear,
criss-crossing
them in this operation.

h.
Check
for front
spring
sag. Also check for broken

spring
leaves, broken center
spring
bolt,
loose
spring

clips
(or tight clips), over-lubrication of spring leaves, spring shackle bracket
loose
on frame, and

loose
rear
spring shackle. Be sure that the shock
absorbers
are operating properly to eliminate bob­bing of the front end.

i.
Check
brakes to make sure that one
does
not

drag.

j.
Check
the steering assembly and steering con­ necting rod.
This
includes the up-and-down-play
of the steering worm shaft, end play of the cross 317

o

STEERING
SYSTEM 0-28.
SBKF1CE
DIAGNOSIS

SYMPTOMS PROBABLE REMEDY
Hard Steering
Lack
of Lubrication Lubricate all Connections
Tie
Rod
Ends
Worn.
Replace

Connecting Rod
Ball
Joints
Tight. Adjust
Cross
Shaft Improperly Adjusted Adjust Steering
Gear
Parts
Worn...................
Replace

Steering
Loose
Tie
Rod
Ends
Worn
Replace

Connecting Rod
Ball
Sockets
Worn
Replace

Steering
Gear
Parts
Worn.
Replace
Steering
Gear
Improperly Adjusted.
......
Adjust
Road Shook; Steering Connecting Rod too Tight;
Axle
Spring
Clip
Loose; Wheel Bearings Loose;
Poor
Shock Absorber

Control,

Turning Radius
Short One
Side
Center
Bolt
in Spring
Sheered
Off,
Axle
Shifted, Steering Arm Bent, Steering Arm not Properly Located

on
Steering
Gear.

0-29.
STEERING
SPECIFICATIONS
F4
ENGINE
V6
ENGINE

STEERING
GEAR:
Make.
Ross
Ross

Type
Cam
and Lever

Cam
and Lever

Ratio..
17.9 to 1
19 to 1
Bearings:
Ball

Cam-Upper
Ball Ball

Cam-Lower
Ball Ball

Lever
Shaft Bushing
Bushing
Steering Column-Upper
Ball
Ball

Lever
Shaft:
.0005*
to
.0025"
[0,0127
a
0,0635
mm.]

Clearance
to Bushing
.0005"
to
.0025"
[0,0127
a
0,0635
mm.j
.0005*
to
.0025"
[0,0127
a
0,0635
mm.]

End
Play .000'
.000"

Lash
at Cam (Straight Ahead) Slight Drag
Slight Drag
Wheel Diameter.
17M*
(438 mm.]
17M*
[438 mm.]
Wheel
Turns.
2.58
2.58

STEERING
GEOMETRY:
King
Pin Inclination
m°
I
72

Toe-In.
W to W U,2 a 2,3 mm.] W to W [1,2 a 2,3 mm.]

Camber
1°
30'

1°
30'

Caster
3°
3°

Turning
Angle:
27K°

DJ,
CJ Models

27K° 273^°

Turning
Radius with 27^° Angle: 17' 6" [5,3 mm.]

CJ-3B,
CJ-5, CJ-5A.
17' 6" [5,3 mm.]
17' 6" [5,3 mm.]

CJ-6,
CJ-6A
22' 10" [7,0 mm.]
22' 10" [7,0 mm.]
Outside Wheel Angle with Inside Wheel at 20°:
20° 20°
322

p

BRAKES
be either a defective master cylinder or the use of
low grade brake fluid which has expanded because
of heat. Use standard duty brake fluid conforming to
SAE-J1703
specification.

P-7.
Bleeding
Brakes

The
hydraulic
brake system must be bled whenever

a
fluid line has been disconnected or air
gets
into the system. A leak in the system may sometimes
be indicated by the presence of a spongy brake
pedal.
Air trapped in the system is compressible

and
does
not permit the pressure, applied to the
brake
pedal, to be transmitted solidly through to
the brakes. The system must be absolutely free
from
air at all times. When bleeding brakes, bleed
at that wheel with the
longest
line from the master
FIG.
P-5—BLEEDING
BRAKES

1—Bleeder
Screw
cylinder
first, the next
longest
second, etc. During
the bleeding operation the master cylinder must
be kept at least %
full
of hydraulic brake fluid.

To
bleed the brakes, first carefully clean all
dirt

from
around the master cylinder filler plug. If
bleeder tank is used follow the manufacturers in­
structions.
Remove the filler plug and
fill
the master
cylinder
to the lower
edge
of filler neck.
Clean
off

all
bleeder connections at all four wheel cylinders.

Attach
bleeder
hose
and fixture to right
rear
wheel

cylinder
bleeder screw and place end of tube in a
glass jar, and submerged in brake fluid. Open the bleeder valve one-half to three-quarters of a
turn.

See
Fig.
P-5.
Depress the
foot
pedal, allowing it to return very
slowly. Continue this pumping action to force the
fluid
through the line and out of the bleeder
hose
which
carries with it any air in the system. When bubbles cease to appear at the end of the bleeder
hose, close the bleeder valve and remove the hose.
After
the bleeding operation at each wheel cylinder
has been completed,
fill
the master cylinder reser­
voir
and replace the filler plug.
Do not re-use the liquid which has been removed

from
the lines through the bleeding process because
of air bubbles and
dirt.

P-8.
Brake Hoses

a.
Hydraulic
lines (tubing and hose) are the means
of transmitting fluid under pressure between the master cylinder and the wheel cylinders.

Note:
On
some
vehicles a proportioning valve is
located in the
rear
brake line along the inside left
frame
side
rail.
The valve is not serviceable and
must be replaced as an assembly.

Should
replacement be necessary make certain the valve is properly positioned with the centerline of
the hex plug (in the bottom of the valve) in the
vertical
position. Refer to Fig. P-l.

The
hoses
are the flexible links between the wheels

or
axles and the frame or body. The
hoses
must

withstand
the fluid pressures without expansion
and
must be free to flex during spring deflection
and
wheel turns without causing damage to the
hose.

b.
Hydraulic
lines are subject to damage and
deterioration. Hoses should be inspected for cuts,

chafing,
cracks,
twists and
loose
frame supports.

Hydraulic
tubing should be inspected for signs of
leakage (due to faulty flares or
loose
connections);

restrictions
(due to dents or corrosion); and wear (due to friction against other metal parts). Always
use correct type and size of wrench on fittings.

Avoid
damage to female fittings by supporting fit­
ting with tube nut during removal of assembly.

c.
On fittings where gaskets are used, always use
a
new gasket. Copper gaskets take a set and may
not form a
good
seal if reused.

d.
When replacing hydraulic brake hose, attach
hose
to wheel cylinder and securely tighten hose,
then attach
opposite
end to frame fitting or tubing.
Avoid
twists in
hose
when assembling to frame fitting
or
tubing. Hold
hose
end securely with

wrench
while attaching tubing to hose. If
hose
end
clip
is used, make certain clip is assembled properly.

Check
for interference during spring deflection or
rebound and during front wheel turns.

e.
Check
for any possible contact between front

brake
hose
and inner sidewall of tire when the front
wheels are in maximum
turn
position.
Check
for sufficient but not excessive length of
hose
between
the clamp and the wheels by turning the wheels
from
one extreme
turn
position to the otherl
f.
Check
that there is no possibility of any contact between the
tail
pipe and
rear
brake
hose
under
all
operating conditions.
P-9.
Brake Pedal Adjustment

There
should always be at least W [12,7 mm.]
free pedal travel before the push rod
engages
the master cylinder piston.

This
adjustment is accomplished by shortening or 326