front pinion JEEP LIBERTY 2002 KJ / 1.G Service Manual

through the tube. The rack gear engages a pinion
gear that drives a gear set in the tensioner housing,
which drives the seat belt retractor spool causing the
slack to be removed from the driver side front seat
belt. Removing excess slack from the driver side front
seat belt not only keeps the occupant properly posi-
tioned for an airbag deployment following a frontal
impact of the vehicle, but also helps to reduce inju-
ries that the occupant of the driver side front seat
might experience in these situations as a result of a
harmful contact with the steering wheel and/or steer-
ing column. Also, the seat belt tensioner has a tor-
sion bar mechanism that is designed to deform in
order to control the loading being applied to the occu-
pant of the driver side front seat by the seat belt dur-
ing a frontal impact, further reducing the potential
for occupant injuries.
The ACM monitors the condition of the seat belt
tensioner through circuit resistance, and will illumi-
nate the airbag indicator in the ElectroMechanical
Instrument Cluster (EMIC) and store a Diagnostic
Trouble Code (DTC) for any fault that is detected.
For proper diagnosis of the seat belt tensioner, a
DRBIIItscan tool is required. Refer to the appropri-
ate diagnostic information.
SEAT BELT TURNING LOOP
ADJUSTER
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE SUPPLEMENTAL RESTRAINT
SYSTEM BEFORE ATTEMPTING ANY STEERING
WHEEL, STEERING COLUMN, DRIVER AIRBAG,
PASSENGER AIRBAG, SEAT BELT TENSIONER,
FRONT IMPACT SENSORS, SIDE CURTAIN AIRBAG,
OR INSTRUMENT PANEL COMPONENT DIAGNOSIS
OR SERVICE. DISCONNECT AND ISOLATE THE
BATTERY NEGATIVE (GROUND) CABLE, THEN
WAIT TWO MINUTES FOR THE SYSTEM CAPACI-
TOR TO DISCHARGE BEFORE PERFORMING FUR-
THER DIAGNOSIS OR SERVICE. THIS IS THE ONLY
SURE WAY TO DISABLE THE SUPPLEMENTAL
RESTRAINT SYSTEM. FAILURE TO TAKE THE
PROPER PRECAUTIONS COULD RESULT IN ACCI-
DENTAL AIRBAG DEPLOYMENT AND POSSIBLE
PERSONAL INJURY.
WARNING: DURING AND FOLLOWING ANY SEAT
BELT SERVICE, CAREFULLY INSPECT ALL SEAT
BELTS, BUCKLES, MOUNTING HARDWARE, AND
RETRACTORS FOR PROPER INSTALLATION,
OPERATION, OR DAMAGE. REPLACE ANY BELTTHAT IS CUT, FRAYED, OR TORN. STRAIGHTEN
ANY BELT THAT IS TWISTED. TIGHTEN ANY
LOOSE FASTENERS. REPLACE ANY BELT THAT
HAS A DAMAGED OR INOPERATIVE BUCKLE OR
RETRACTOR. REPLACE ANY BELT THAT HAS A
BENT OR DAMAGED LATCH PLATE OR ANCHOR
PLATE. NEVER ATTEMPT TO REPAIR A SEAT BELT
COMPONENT. ALWAYS REPLACE DAMAGED OR
FAULTY SEAT BELT COMPONENTS WITH THE COR-
RECT, NEW AND UNUSED REPLACEMENT PARTS
LISTED IN THE MOPAR PARTS CATALOG.
(1) Disconnect and isolate the battery negative
cable. Wait two minutes for the system capacitor to
discharge before further service.
(2) Unsnap and lift the trim cover to access the
nut that secures the front seat belt turning loop to
the height adjuster on the upper B-pillar.
(3) Remove the nut that secures the seat belt turn-
ing loop to the height adjuster stud on the upper
B-pillar.
(4) Remove the seat belt turning loop from the
height adjuster stud.
(5) Remove the upper trim from the inside of the
B-pillar. (Refer to 23 - BODY/INTERIOR/B-PILLAR
UPPER TRIM - REMOVAL).
(6) Remove the screw that secures the seat belt
turning loop adjuster to the upper B-pillar (Fig. 35).
(7) Pull the upper end of the turning loop adjuster
away from the B-pillar far enough to disengage the
hooks on the lower end of the adjuster from the slots
in the B-pillar.
(8) Remove the seat belt turning loop adjuster
from the B-pillar.
Fig. 35 Seat Belt Turning Loop Adjuster Remove/
Install
1 - SCREW
2 - B-PILLAR
3 - ADJUSTER
KJRESTRAINTS 8O - 37
SEAT BELT TENSIONER (Continued)

STEERING
TABLE OF CONTENTS
page page
STEERING
DESCRIPTION..........................1
OPERATION............................1
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - POWER
STEERING SYSTEM....................1DIAGNOSIS AND TESTING - POWER
STEERING FLOW AND PRESSURE........3
COLUMN...............................5
GEAR.................................13
LINKAGE..............................16
PUMP.................................17
STEERING
DESCRIPTION
Power steering systems consist of:
²Steering column & Intermediate Shaft
²Rack and pinion steering gear
²Belt driven hydraulic steering pump
²Pump pressure, supply and return hoses
²Oil Cooler
OPERATION
The steering column intermediate shaft attaches
the steering column to the gear pinion. The rotation
of the pinion moves the gear rack from side-to-side.
This lateral action of the rack pushes and pulls the
tie rods to change the direction of the front wheels.
Power assist is provided by an engine mounted
hydraulic pump. The pump supplies hydraulic fluid
to the steering gear. All vehicles are equipped with
an oil cooler.
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - POWER STEERING SYSTEM
STEERING NOISE
There is some noise in all power steering systems. One of the most common is a hissing sound evident at a
standstill/parking, or when the steering is at the end of it's travel. Hiss is a high frequency noise similar to that
of a water tap being closed slowly. The noise is present in all valves that have a high velocity fluid passing through
an orifice. There is no relationship between this noise and steering performance.
CONDITION POSSIBLE CAUSES CORRECTION
OBJECTIONAL HISS OR
WHISTLE1. Steering intermediate shaft to dash panel
seal.1. Check and repair seal at dash
panel.
2. Noisy valve in power steering gear. 2. Replace steering gear.
1. Gear mounting bolts loose. 1. Tighten bolts to specification.
2. Loose or damaged suspension
components.2. Inspect and repair suspension.
3. Internal gear noise. 3. Replace steering gear.
4. Loose or damaged intermediate shaft or
column.4. Inspect and repair or replace.
MOAN Pressure hose in contact with other
components.Reposition hose.
CHIRP OR SQUEAL 1. Loose belt. 1. Adjust or replace.
KJSTEERING 19 - 1

GEAR
TABLE OF CONTENTS
page page
GEAR
DESCRIPTION.........................13
OPERATION...........................13
REMOVAL
REMOVAL - 4WD......................13
REMOVAL - 2WD......................14
INSTALLATION
INSTALLATION - 4WD..................14INSTALLATION - 2WD..................14
SPECIFICATIONS
TORQUE CHART......................15
SPECIAL TOOLS
OUTER TIE ROD END REMOVAL TOOL....15
GEAR
DESCRIPTION
A rack and pinion steering gear (Fig. 1) is made up
of two main components, the pinon shaft and the
rack. The gear cannot be adjusted or internally ser-
viced. If a malfunction or a fluid leak occurs, the gear
must be replaced as an assembly.
OPERATION
The steering column intermediate shaft is attached
to the gear pinion. The rotation of the pinion moves
the gear rack from side-to-side. This lateral action of
the rack pushes and pulls the tie rods, which are
connected to the steering knuckles to change the
direction of the front wheels.
REMOVAL
REMOVAL - 4WD
(1) Siphon the power steering fluid from the power
steering reservoir.
(2) Lock the steering wheel to prevent spinning of
the clockspring.
(3) Raise and support the vehicle.
(4) Remove the skid plate from under the front
end to gain access to the gear (Refer to 13 - FRAME
& BUMPERS/FRAME/FRONT SKID PLATE -
REMOVAL).
(5) Remove the front tire and wheel assemblies.
NOTE: Mark the alignment adjusting cams for eas-
ier installation.
(6) Remove the lower control arms. (Refer to 2 -
SUSPENSION/FRONT/LOWER CONTROL ARM -
REMOVAL).
(7) Remove the front axle. (Refer to 3 - DIFFER-
ENTIAL & DRIVELINE/FRONT AXLE - REMOV-
AL).
(8) Remove the tie rod end nuts.
(9) Separate tie rod ends from the knuckles with
Puller C-3894-A.
(10) Remove the intermediate shaft lower coupler
bolt and slide the coupler off the gear (Fig. 2).
(11) Remove power steering pressure hose bracket
(Fig. 3).
(12) Remove the power steering lines from the
gear (Fig. 2).
(13) Remove the mounting bolts from the gear to
the front cradle (Fig. 3).
(14) Remove the steering gear from the vehicle.
Fig. 1 Rack & Pinion Steering Gear
1 - TIE ROD - INNER
2 - TIE ROD - INNER
3 - TIE ROD END - OUTER LH
4 - BOOTS
5 - TIE ROD END - OUTER RH
KJGEAR 19 - 13

REMOVAL - 2WD
(1) Siphon the power steering fluid from the power
steering reservoir.
(2) Lock the steering wheel to prevent spinning of
the clockspring.
(3) Raise and support the vehicle.
(4) Remove the skid plate from under the front
end to gain access to the gear(Refer to 13 - FRAME
& BUMPERS/FRAME/FRONT SKID PLATE -
REMOVAL).
(5) Remove the tire and wheel assembly.
NOTE: Mark the alignment adjusting cams and tie
rod end jam nuts on the steering gear for easier
installation.
(6) Remove the tie rod end nuts.
(7) Separate tie rod ends from the knuckles with
Puller C-3894-A.
(8) Remove the lower intermediate shaft coupler
bolt and slide the coupler off the gear (Fig. 2).(9) Remove power steering pressure hose bracket
(Fig. 3).
(10) Remove the power steering lines from the
gear (Fig. 2).
(11) Remove the mounting bolts from the gear to
the front cradle (Fig. 3).
(12) Remove the steering gear from the vehicle.
INSTALLATION
INSTALLATION - 4WD
(1) Transfer the tie rod ends to the new steering
gear (if needed).
(2) Install the steering gear to the vehicle.
(3) Install the gear mounting bolts to the front cra-
dle. (Fig. 3). Tighten the gear mounting bolts to 162
N´m (120 ft.lbs.)
(4) Install the power steering lines to the gear
(Fig. 2).
(5) Install the power steering pressure hose
bracket (Fig. 3).
(6) Install the lower coupler bolt and slide the cou-
pler on to the gear (Fig. 2).
(7) Install the tie rod end to the knuckle and
tighten the nuts.
(8) Install the front axle. (Refer to 3 - DIFFEREN-
TIAL & DRIVELINE/FRONT AXLE - INSTALLA-
TION).
(9) Install the lower control arms. (Refer to 2 -
SUSPENSION/FRONT/LOWER CONTROL ARM -
INSTALLATION).
(10) Install the tire and wheel assembly. (Refer to
22 - TIRES/WHEELS/WHEELS - STANDARD PRO-
CEDURE).
(11) Install the skid plate (Refer to 13 - FRAME &
BUMPERS/FRAME/FRONT SKID PLATE - INSTAL-
LATION).
(12) Lower the vehicle.
(13) Unlock the steering wheel.
(14) Fill the power steering fluid (Refer to 19 -
STEERING/PUMP - STANDARD PROCEDURE).
(15) Reset the toe and center the steering wheel
(Refer to 2 - SUSPENSION/WHEEL ALIGNMENT -
STANDARD PROCEDURE).
INSTALLATION - 2WD
(1) Transfer the outer tie rod ends to the new
steering gear (if needed).
(2) Install the steering gear to the vehicle.
(3) Install the gear mounting bolts to the front cra-
dle. (Fig. 3). Tighten the gear mounting bolts to 162
N´m (120 ft.lbs.)
(4) Install the power steering lines to the gear
(Fig. 2).
Fig. 2 COUPLER BOLT
Fig. 3 RACK & PINION
19 - 14 GEARKJ
GEAR (Continued)

(5) Install the power steering pressure hose
bracket (Fig. 3).
(6) Install the lower coupler bolt and slide the cou-
pler on to the gear (Fig. 2).
(7) Install the tie rod end to the knuckle and
tighten the nuts.
(8) Install the tire and wheel assembly. (Refer to
22 - TIRES/WHEELS/WHEELS - STANDARD PRO-
CEDURE).
(9) Install the skid plate(Refer to 13 - FRAME &
BUMPERS/FRAME/FRONT SKID PLATE - INSTAL-
LATION).(10) Lower the vehicle.
(11) Unlock the steering wheel.
(12) Fill the power steering fluid (Refer to 19 -
STEERING/PUMP - STANDARD PROCEDURE).
(13) Reset the toe and center the steering wheel
(Refer to 2 - SUSPENSION/WHEEL ALIGNMENT -
STANDARD PROCEDURE).
SPECIFICATIONS
TORQUE CHART
TORQUE SPECIFICATIONS
DESCRIPTION N´m Ft. Lbs. In. Lbs.
Rack and Pinion Steering
Gear
Gear to Frame Bolts162 120 Ð
Rack and Pinion Steering
Gear
Intermediate Shaft Bolt49 36 Ð
Tie Rod End
Knuckle Nut108 80 Ð
Tie Rod End
Jam Nut75 55 Ð
Power Steering Line
Pressure Line35 25 Ð
Power Steering Line
Return Line35 25 Ð
SPECIAL TOOLS
OUTER TIE ROD END REMOVAL TOOL
Puller C-3894-A
KJGEAR 19 - 15
GEAR (Continued)

OPERATION - DESCRIPTION, MODES OF . . 8E-11
OPERATION - DIAGNOSIS AND TESTING,
AIR CHECKING TRANSMISSION
CLUTCH............................21-80
ORDER, 2.4L 4-CYLINDER - ENGINE
FIRING..............................8I-2
ORDER, 3.7L V-6 - ENGINE FIRING........8I-2
ORIFICE TUBE - DESCRIPTION, A/C......24-50
ORIFICE TUBE - INSTALLATION, A/C......24-50
ORIFICE TUBE - OPERATION, A/C........24-50
ORIFICE TUBE - REMOVAL, A/C.........24-50
ORVR - DESCRIPTION.................25-29
ORVR - OPERATION..................25-29
OUT - ADJUSTMENT, LOCK..............5-30
OUTBOARD SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-34
OUTBOARD SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-33
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-186
OUTER BELT MOLDING - INSTALLATION,
REAR DOOR.......................23-186
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-186
OUTER BELT MOLDING - REMOVAL,
REAR DOOR.......................23-186
OUTER TIE ROD END REMOVAL TOOL,
SPECIAL TOOLS.....................19-15
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-11
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER.........................8W-97-11
OUTLET - INSTALLATION, POWER....8W-97-13
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER......8W-97-11
OUTLET - REMOVAL, POWER........8W-97-12
OUTLET BARRELS - INSTALLATION,
PANEL.............................24-29
OUTLET BARRELS - REMOVAL, PANEL . . . 24-29
OUTLETS - DESCRIPTION, DEMISTER....24-29
OUTPUT - DESCRIPTION, PCM...........8I-4
OUTPUT - OPERATION, PCM............14-33
OUTPUT - OPERATION, PCM.............8I-4
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - INSTALLATION,
REAR.............................21-212
OUTPUT SHAFT SEAL - REMOVAL,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - REMOVAL, REAR . 21-210
OUTPUT SPEED SENSOR - DESCRIPTION . 21-152
OUTPUT SPEED SENSOR -
INSTALLATION......................21-152
OUTPUT SPEED SENSOR - OPERATION . . 21-152
OUTPUT SPEED SENSOR - REMOVAL . . . 21-152
OVERDRIVE OFF INDICATOR -
DESCRIPTION.......................8J-26
OVERDRIVE OFF INDICATOR -
OPERATION.........................8J-26
OVERDRIVE SWITCH - DESCRIPTION....21-153
OVERDRIVE SWITCH - OPERATION.....21-153
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE, REMOVAL........8M-4
OVERRIDE RELAY - DESCRIPTION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - INSTALLATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - OPERATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - REMOVAL, CLUTCH
SWITCH.............................6-10
OXYGEN SENSOR - DESCRIPTION.......14-40
OXYGEN SENSOR - INSTALLATION.......14-43
OXYGEN SENSOR - OPERATION.........14-40
OXYGEN SENSOR - REMOVAL..........14-41
PADS - INSTALLATION, FRONT BRAKE.....5-11
PADS - REMOVAL, FRONT BRAKE........5-11
PAINT CODE - DESCRIPTION..........23-162
PAINT CODES - SPECIFICATIONS.......23-162
PAINT TOUCH-UP - DESCRIPTION
......23-163
PAN - CLEANING, OIL
..................9-63
PAN - DESCRIPTION, OIL
...............9-63
PAN - INSPECTION, OIL
................9-63
PAN - INSTALLATION, OIL
...............9-64PAN - REMOVAL, OIL..................9-63
PANEL - DESCRIPTION, LATCH - ACCESS . 23-139
PANEL - INSTALLATION, GLASS........23-178
PANEL - INSTALLATION, LATCH -
ACCESS...........................23-139
PANEL - INSTALLATION, QUARTER TRIM . 23-159
PANEL - INSTALLATION, TRIM . . . 23-126,23-132,
23-138
PANEL - REMOVAL, GLASS............23-178
PANEL - REMOVAL, LATCH - ACCESS . . . 23-139
PANEL - REMOVAL, QUARTER TRIM....23-159
PANEL - REMOVAL, TRIM . 23-125,23-132,23-138
PANEL ADJUSTMENT, ADJUSTMENTS -
SUNROOF GLASS...................23-178
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-8
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-7
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT......................23-151
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT......................23-149
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT......................23-154
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT......................23-154
PANEL DOOR - INSTALLATION..........24-36
PANEL DOOR ACTUATOR -
INSTALLATION.......................24-25
PANEL DOOR ACTUATOR - REMOVAL....24-24
PANEL DRIVER SIDE BEZELS -
INSTALLATION, INSTRUMENT..........23-154
PANEL DRIVER SIDE BEZELS -
REMOVAL, INSTRUMENT.............23-153
PANEL END CAP - INSTALLATION,
INSTRUMENT......................23-153
PANEL END CAP - REMOVAL,
INSTRUMENT......................23-153
PANEL OUTLET BARRELS -
INSTALLATION.......................24-29
PANEL OUTLET BARRELS - REMOVAL....24-29
PANEL PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT..........23-154
PANEL PASSENGER SIDE BEZEL -
REMOVAL, INSTRUMENT.............23-154
PANEL SEAL - INSTALLATION, GLASS . . . 23-178
PANEL SEAL - REMOVAL, GLASS.......23-178
PANEL TOP COVER - INSTALLATION,
INSTRUMENT......................23-153
PANEL TOP COVER - REMOVAL,
INSTRUMENT......................23-152
PARK - INTERLOCK CABLE -
INSTALLATION......................21-153
PARK - INTERLOCK CABLE - REMOVAL . . 21-153
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PARK RAMP - INSTALLATION, WIPER
ARM ..............................8R-43
PARK RAMP - REMOVAL, WIPER ARM . . . 8R-43
PARKING BRAKE - DESCRIPTION.........5-29
PARKING BRAKE - OPERATION...........5-29
PARK-INTERLOCK CABLE -
ADJUSTMENTS.....................21-154
PART TIME INDICATOR - DESCRIPTION . . . 8J-29
PART TIME INDICATOR - OPERATION.....8J-29
PASSENGER AIRBAG - DESCRIPTION....8O-27
PASSENGER AIRBAG - INSTALLATION....8O-29
PASSENGER AIRBAG - OPERATION......8O-27
PASSENGER AIRBAG - REMOVAL........8O-28
PASSENGER AIRBAG DOOR -
INSTALLATION......................8O-30
PASSENGER AIRBAG DOOR - REMOVAL . . 8O-29
PASSENGER AIRBAG MOUNTING
BRACKET - INSTALLATION.............8O-31
PASSENGER AIRBAG MOUNTING
BRACKET - REMOVAL
.................8O-31
PASSENGER SEAT HEATER SWITCH -
DESCRIPTION
.......................8G-14
PASSENGER SEAT HEATER SWITCH -
INSTALLATION
......................8G-15
PASSENGER SEAT HEATER SWITCH -
OPERATION
.........................8G-14
PASSENGER SEAT HEATER SWITCH -
REMOVAL
..........................8G-15PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT PANEL....23-154
PASSENGER SIDE BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION..................8E-11
PCM - OPERATION...................8E-14
PCM INPUT - OPERATION, ASD SENSE.....8I-4
PCM OUTPUT - DESCRIPTION............8I-4
PCM OUTPUT - OPERATION............14-33
PCM OUTPUT - OPERATION.............8I-4
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE.........................8E-1
PCV VALVE - DESCRIPTION............25-29
PCV VALVE - DIAGNOSIS AND TESTING . . . 25-31
PCV VALVE - INSTALLATION............25-32
PCV VALVE - OPERATION..............25-31
PCV VALVE - REMOVAL...............25-32
PEDAL - DESCRIPTION.................5-20
PEDAL - INSTALLATION................5-20
PEDAL - INSTALLATION, ACCELERATOR . . . 14-30
PEDAL - INSTALLATION, CLUTCH.........6-10
PEDAL - OPERATION...................5-20
PEDAL - REMOVAL....................5-20
PEDAL - REMOVAL, ACCELERATOR......14-29
PEDAL - REMOVAL, CLUTCH............6-10
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-11
PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-11
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-11
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-2
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-4
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PILOT BEARING - INSTALLATION..........6-8
PILOT BEARING - REMOVAL..............6-8
PINION GEAR/RING GEAR -
INSTALLATION........................3-46
PINION GEAR/RING GEAR - REMOVAL.....3-44
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION...................3-112,3-82
PINION GEAR/RING GEAR/TONE RING -
REMOVAL......................3-110,3-79
PINION SEAL - INSTALLATION . . 3-103,3-39,3-68
PINION SEAL - REMOVAL......3-102,3-38,3-68
PIPE - INSTALLATION, CROSS-OVER......11-3
PIPE - REMOVAL, CROSS-OVER..........11-3
PISTON & CONNECTING ROD -
DESCRIPTION........................9-49
PISTON FITTING - STANDARD
PROCEDURE.........................9-50
PISTON RING FITTING - STANDARD
PROCEDURE.........................9-52
PISTONS - DESCRIPTION.............21-155
PISTONS - OPERATION...............21-155
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-160
PLANETARY GEARTRAIN - CLEANING....21-159
PLANETARY GEARTRAIN - DESCRIPTION . 21-157
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-159
PLANETARY GEARTRAIN - INSPECTION . . 21-159
PLANETARY GEARTRAIN - OPERATION . . 21-157
PLATE - INSTALLATION, DOOR SILL
SCUFF............................23-157
PLATE - INSTALLATION, FLEX............9-49
PLATE - INSTALLATION, FRONT SKID......13-6
PLATE - INSTALLATION, FUEL TANK
SKID...............................13-9
PLATE - INSTALLATION, REAR DOOR
SCUFF............................23-160
PLATE - INSTALLATION, TRANSFER
CASE SKID..........................13-7
PLATE - REMOVAL, DOOR SILL SCUFF . . . 23-157
PLATE - REMOVAL, FLEX...............9-49
PLATE - REMOVAL, FRONT SKID.........13-6
PLATE - REMOVAL, FUEL TANK SKID
......13-9
PLATE - REMOVAL, REAR DOOR SCUFF
. . 23-160
PLATE - REMOVAL, TRANSFER CASE
SKID
...............................13-7
PLATE LAMP BULB - INSTALLATION,
LICENSE
...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE
...........................8L-44
18 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

RELAY - OPERATION, FRONT FOG LAMP . . 8L-22
RELAY - OPERATION, FUEL PUMP.......14-34
RELAY - OPERATION, HEADLAMP HIGH
BEAM..............................8L-33
RELAY - OPERATION, HEADLAMP LOW
BEAM..............................8L-39
RELAY - OPERATION, PARK LAMP.......8L-54
RELAY - OPERATION, REAR FOG LAMP . . . 8L-57
RELAY - OPERATION, REAR WINDOW
DEFOGGER..........................8G-6
RELAY - OPERATION, STARTER MOTOR . . . 8F-42
RELAY - OPERATION, TRAILER TOW.....8L-62
RELAY - OPERATION, TRANSMISSION
CONTROL.........................21-168
RELAY - OPERATION, WIPER HIGH/LOW . . 8R-23
RELAY - OPERATION, WIPER ON/OFF....8R-25
RELAY - REMOVAL................8W-97-14
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-16
RELAY - REMOVAL, AMPLIFIER CHOKE....8A-4
RELAY - REMOVAL, BLOWER MOTOR....24-21
RELAY - REMOVAL, CLUTCH SWITCH
OVERRIDE...........................6-10
RELAY - REMOVAL, DAYTIME RUNNING
LAMP..............................8L-21
RELAY - REMOVAL, DOOR LOCK.........8N-6
RELAY - REMOVAL, FRONT FOG LAMP . . . 8L-24
RELAY - REMOVAL, FUEL PUMP........14-34
RELAY - REMOVAL, HEADLAMP HIGH
BEAM..............................8L-34
RELAY - REMOVAL, HEADLAMP LOW
BEAM..............................8L-40
RELAY - REMOVAL, HORN..............8H-3
RELAY - REMOVAL, PARK LAMP........8L-55
RELAY - REMOVAL, REAR FOG LAMP....8L-58
RELAY - REMOVAL, REAR WINDOW
DEFOGGER..........................8G-7
RELAY - REMOVAL, STARTER MOTOR....8F-43
RELAY - REMOVAL, TRAILER TOW.......8L-63
RELAY - REMOVAL, WIPER HIGH/LOW . . . 8R-24
RELAY - REMOVAL, WIPER ON/OFF......8R-26
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-4
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-4
RELEASE BEARING - INSTALLATION,
CLUTCH..............................6-6
RELEASE BEARING - REMOVAL, CLUTCH . . . 6-6
RELEASE CABLE - INSTALLATION, LATCH . 23-120
RELEASE CABLE - REMOVAL, LATCH....23-120
RELEASE HANDLE - INSTALLATION,
LATCH ............................23-120
RELEASE HANDLE - REMOVAL, LATCH . . 23-120
RELEASE SWITCH - DIAGNOSIS AND
TESTING, FLIP-UP GLASS..............8N-5
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-42
RELIEF VALVE - OPERATION, HIGH
PRESSURE.........................24-42
REMOTE KEYLESS ENTRY MODULE -
DESCRIPTION........................8N-7
REMOTE KEYLESS ENTRY MODULE -
DIAGNOSIS AND TESTING..............8N-7
REMOTE KEYLESS ENTRY MODULE -
INSTALLATION.......................8N-7
REMOTE KEYLESS ENTRY MODULE -
OPERATION..........................8N-7
REMOTE KEYLESS ENTRY MODULE -
REMOVAL...........................8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-8
REMOTE KEYLESS ENTRY
TRANSMITTER - SPECIFICATIONS........8N-9
REMOTE SWITCHES - DESCRIPTION.....8A-11
REMOTE SWITCHES - DIAGNOSIS AND
TESTING...........................8A-12
REMOTE SWITCHES - INSTALLATION.....8A-13
REMOTE SWITCHES - OPERATION.......8A-12
REMOTE SWITCHES - REMOVAL
........8A-13
REPAIR - DESCRIPTION, THREADED
HOLE
.............................Intro.-4
REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD
..................21-81
REPAIR - STANDARD PROCEDURE,
REAR GLASS HEATING GRID
............8G-4
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE
...............9-9REPAIRING LEAKS - STANDARD
PROCEDURE.........................22-8
REPEATER LAMP BULB - INSTALLATION . . 8L-60
REPEATER LAMP BULB - REMOVAL......8L-60
REPEATER LAMP UNIT - INSTALLATION . . 8L-61
REPEATER LAMP UNIT - REMOVAL......8L-60
REQUIREMENTS - DESCRIPTION,
COOLING SYSTEM....................24-1
RESERVOIR - DESCRIPTION, VACUUM....8P-7
RESERVOIR - DESCRIPTION, WASHER . . . 8R-21
RESERVOIR - DIAGNOSIS AND TESTING,
VACUUM............................8P-7
RESERVOIR - INSTALLATION, FLUID......5-26
RESERVOIR - INSTALLATION, VACUUM....8P-8
RESERVOIR - INSTALLATION, WASHER . . . 8R-22
RESERVOIR - OPERATION, VACUUM......8P-7
RESERVOIR - OPERATION, WASHER.....8R-21
RESERVOIR - REMOVAL, FLUID..........5-26
RESERVOIR - REMOVAL, VACUUM........8P-7
RESERVOIR - REMOVAL, WASHER......8R-21
RESISTANCE, 2.4L - IGNITION COIL.......8I-2
RESISTANCE, 2.4L - SPARK PLUG CABLE . . . 8I-3
RESISTANCE, 3.7L V-6 - IGNITION COIL....8I-3
RESISTOR - DESCRIPTION, BLOWER
MOTOR............................24-22
RESISTOR - DIAGNOSIS AND TESTING,
BLOWER MOTOR....................24-22
RESISTOR - INSTALLATION, BLOWER
MOTOR............................24-22
RESISTOR - OPERATION, BLOWER
MOTOR............................24-22
RESISTOR - REMOVAL, BLOWER
MOTOR............................24-22
RESTRAINT DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL......................8O-6
RESTRAINT SYSTEM - DIAGNOSIS AND
TESTING, SUPPLEMENTAL..............8O-6
RESTRAINT SYSTEM - WARNING........8O-5
RESTRAINTS - DESCRIPTION............8O-2
RESTRAINTS - OPERATION.............8O-4
RESTRAINTS - STANDARD PROCEDURE,
HANDLING NON-DEPLOYED
SUPPLEMENTAL......................8O-6
RETAINER/BULKHEAD - ASSEMBLY, 4C . . 21-123
RETAINER/BULKHEAD - DISASSEMBLY,
4C ...............................21-122
RETRACTOR - INSTALLATION, FRONT
SEAT BELT .........................8O-24
RETRACTOR - INSTALLATION, REAR
CENTER SEAT BELT..................8O-33
RETRACTOR - INSTALLATION, REAR
OUTBOARD SEAT BELT................8O-34
RETRACTOR - REMOVAL, FRONT SEAT
BELT ..............................8O-23
RETRACTOR - REMOVAL, REAR CENTER
SEAT BELT .........................8O-32
RETRACTOR - REMOVAL, REAR
OUTBOARD SEAT BELT................8O-33
RETURN - DESCRIPTION, SENSOR.......8E-14
RETURN HOSE (GEAR TO THE COOLER)
- INSTALLATION.....................19-22
RETURN HOSE (GEAR TO THE COOLER)
- REMOVAL.........................19-21
RETURN HOSE (RESERVOIR TO THE
COOLER) - INSTALLATION.............19-22
RETURN HOSE (RESERVOIR TO THE
COOLER) - REMOVAL
.................19-21
REVERSE FLUSHING - STANDARD
PROCEDURE, COOLING SYSTEM
.........7-12
RFE TRANSMISSION, SPECIAL TOOLS
. . . 21-120
RHD - INSTALLATION
...............8W-97-6
RHD - REMOVAL
...................8W-97-5
RIGHT POWER SEAT SWITCH -
DESCRIPTION
.......................8N-19
RIGHT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING
.............8N-19
RIGHT POWER SEAT SWITCH -
INSTALLATION
......................8N-20
RIGHT POWER SEAT SWITCH -
OPERATION
.........................8N-19
RIGHT POWER SEAT SWITCH -
REMOVAL
..........................8N-20
RIGHT SIDE - INSTALLATION
........2-12,2-15
RIGHT SIDE - REMOVAL
............2-11,2-14
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE
...........3-112,3-82RING - REMOVAL, PINION GEAR/RING
GEAR/TONE.....................3-110,3-79
RING FITTING - STANDARD
PROCEDURE, PISTON..................9-52
RISER - INSTALLATION, MANUAL SEAT . . 23-168
RISER - REMOVAL, MANUAL SEAT......23-167
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-8
RKE TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE.........................8N-8
RKE TRANSMITTER PROGRAMING -
STANDARD PROCEDURE...............8N-9
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-2
ROAD TESTING - DIAGNOSIS AND
TESTING...........................21-78
ROCKER ARM - DESCRIPTION.......9-29,9-37
ROCKER ARM - INSTALLATION..........9-37
ROCKER ARM - REMOVAL..............9-37
ROD - DESCRIPTION, PISTON &
CONNECTING.........................9-49
ROD BEARING - FITTING - STANDARD
PROCEDURE, CONNECTING.............9-40
ROD BEARING, FITTING - CONNECTING....9-49
ROD END - INSTALLATION, TIE.........19-16
ROD END - REMOVAL, TIE.............19-16
ROD END REMOVAL TOOL, SPECIAL
TOOLS - OUTER TIE..................19-15
ROTATION - STANDARD PROCEDURE,
TIRE................................22-2
ROTOR - DIAGNOSIS AND TESTING,
DISC BRAKE.........................5-18
ROTOR - STANDARD PROCEDURE, DISC
BRAKE..............................5-19
ROTORS - INSTALLATION...............5-19
ROTORS - REMOVAL..................5-19
ROUTING 3.7L ENGINE - DESCRIPTION,
COOLING SYSTEM.....................7-2
RUN CHANNEL - INSTALLATION, GLASS . 23-123,
23-130
RUN CHANNEL - REMOVAL, GLASS....23-123,
23-130
RUNNING LAMP RELAY - DESCRIPTION,
DAYTIME...........................8L-20
RUNNING LAMP RELAY - INSTALLATION,
DAYTIME...........................8L-21
RUNNING LAMP RELAY - OPERATION,
DAYTIME...........................8L-20
RUNNING LAMP RELAY - REMOVAL,
DAYTIME...........................8L-21
RUNOUT - DIAGNOSIS AND TESTING,
TIRES AND WHEEL....................22-1
SAFETY CERTIFICATION LABEL -
DESCRIPTION, VEHICLE..............Intro.-9
SAFETY PRECAUTIONS AND WARNINGS,
WARNING...........................23-1
SAFETY PRECAUTIONS, WARNING -
WINDSHIELD.......................23-173
SANDING/BUFFING & POLISHING -
DESCRIPTION, FINESSE..............23-163
SCHEDULES - DESCRIPTION,
MAINTENANCE........................0-4
SCHEMATICS AND DIAGRAMS -
HYDRAULIC SCHEMATICS.............21-100
SCHEMATICS, SCHEMATICS AND
DIAGRAMS - HYDRAULIC.............21-100
SCUFF PLATE - INSTALLATION, DOOR
SILL..............................23-157
SCUFF PLATE - INSTALLATION, REAR
DOOR............................23-160
SCUFF PLATE - REMOVAL, DOOR SILL . . . 23-157
SCUFF PLATE - REMOVAL, REAR DOOR . . 23-160
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL.....................9-47
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL.....................9-46
SEAL - INSTALLATION, ADAPTER
HOUSING..........................21-124
SEAL - INSTALLATION, A-PILLAR.......23-185
SEAL - INSTALLATION, COWL/PLENUM . . 23-187
SEAL - INSTALLATION, COWL/PLENUM
WINDOW BAFFLE
...................23-187
SEAL - INSTALLATION, FRONT OUTPUT
SHAFT
......................21-208,21-246
SEAL - INSTALLATION, GLASS PANEL
. . . 23-178
SEAL - INSTALLATION, OIL PUMP
FRONT
............................21-152
SEAL - INSTALLATION, PINION
. . 3-103,3-39,3-68
22 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

SEAL - INSTALLATION, REAR OUTPUT
SHAFT............................21-212
SEAL - NV1500 - INSTALLATION,
EXTENSION HOUSING.................21-32
SEAL - NV1500 - REMOVAL, EXTENSION
HOUSING...........................21-32
SEAL - NV3550 - INSTALLATION,
EXTENSION HOUSING.................21-74
SEAL - NV3550 - REMOVAL, EXTENSION
HOUSING...........................21-74
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL.....................9-48
SEAL - REAR - REMOVAL, CRANKSHAFT
OIL ................................9-48
SEAL - REMOVAL, ADAPTER HOUSING . . 21-124
SEAL - REMOVAL, A-PILLAR...........23-185
SEAL - REMOVAL, COWL/PLENUM......23-187
SEAL - REMOVAL, COWL/PLENUM
WINDOW BAFFLE...................23-187
SEAL - REMOVAL, FRONT OUTPUT
SHAFT......................21-208,21-246
SEAL - REMOVAL, GLASS PANEL.......23-178
SEAL - REMOVAL, OIL PUMP FRONT....21-152
SEAL - REMOVAL, PINION.....3-102,3-38,3-68
SEAL - REMOVAL, REAR OUTPUT SHAFT . 21-210
SEAL AREA LEAKS - DIAGNOSIS AND
TESTING, REAR.......................9-61
SEALER LOCATIONS - SPECIFICATIONS . . . 23-87
SEALS - DESCRIPTION, VALVE GUIDE . 9-29,9-38
SEALS - INSTALLATION, AXLE SHAFT....3-102,
3-38
SEALS - REMOVAL, AXLE SHAFT....3-101,3-37
SEAT - FRONT - INSTALLATION........23-165
SEAT - FRONT - REMOVAL............23-165
SEAT - REAR - INSTALLATION.........23-168
SEAT - REAR - REMOVAL.............23-168
SEAT BACK - FRONT - INSTALLATION . . . 23-166
SEAT BACK - FRONT - REMOVAL.......23-166
SEAT BACK - REAR - INSTALLATION....23-168
SEAT BACK - REAR - REMOVAL........23-168
SEAT BACK COVER - FRONT -
INSTALLATION......................23-167
SEAT BACK COVER - FRONT - REMOVAL . 23-166
SEAT BACK COVER - REAR -
INSTALLATION......................23-169
SEAT BACK COVER - REAR - REMOVAL . . 23-169
SEAT BACK CUSHION - FRONT -
INSTALLATION......................23-167
SEAT BACK CUSHION - FRONT -
REMOVAL.........................23-167
SEAT BACK CUSHION - REAR -
INSTALLATION......................23-170
SEAT BACK CUSHION - REAR -
REMOVAL.........................23-170
SEAT BACK FRAME - REAR -
INSTALLATION......................23-171
SEAT BACK FRAME - REAR - REMOVAL . . 23-171
SEAT BACK LATCH / LOCK -
INSTALLATION, FOLDING REAR........23-170
SEAT BACK LATCH / LOCK - REMOVAL,
FOLDING REAR.....................23-170
SEAT BACK LATCH STRIKER -
INSTALLATION, REAR................23-171
SEAT BACK LATCH STRIKER - REMOVAL,
REAR.............................23-170
SEAT BACK RECLINER - FRONT -
INSTALLATION......................23-166
SEAT BACK RECLINER - FRONT -
REMOVAL.........................23-166
SEAT BELT & RETRACTOR -
INSTALLATION, FRONT................8O-24
SEAT BELT & RETRACTOR -
INSTALLATION, REAR CENTER..........8O-33
SEAT BELT & RETRACTOR -
INSTALLATION, REAR OUTBOARD.......8O-34
SEAT BELT & RETRACTOR - REMOVAL,
FRONT.............................8O-23
SEAT BELT & RETRACTOR - REMOVAL,
REAR CENTER.......................8O-32
SEAT BELT & RETRACTOR - REMOVAL,
REAR OUTBOARD....................8O-33
SEAT BELT BUCKLE - INSTALLATION,
FRONT
.............................8O-26
SEAT BELT BUCKLE - INSTALLATION,
REAR
..............................8O-35
SEAT BELT BUCKLE - REMOVAL, FRONT
. . 8O-25
SEAT BELT BUCKLE - REMOVAL, REAR
. . . 8O-34
SEAT BELT SWITCH - DESCRIPTION
.....8O-35SEAT BELT SWITCH - OPERATION.......8O-36
SEAT BELT TENSIONER - DESCRIPTION . . . 8O-36
SEAT BELT TENSIONER - OPERATION....8O-36
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-38
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-37
SEAT CUSHION - FRONT -
INSTALLATION......................23-167
SEAT CUSHION - FRONT - REMOVAL....23-167
SEAT CUSHION - REAR - INSTALLATION . 23-171
SEAT CUSHION - REAR - REMOVAL.....23-171
SEAT CUSHION COVER - FRONT -
INSTALLATION......................23-167
SEAT CUSHION COVER - FRONT -
REMOVAL.........................23-167
SEAT CUSHION SIDE SHIELDS -
INSTALLATION......................23-167
SEAT CUSHION SIDE SHIELDS -
REMOVAL.........................23-167
SEAT ELEMENT - DESCRIPTION, HEATED . 8G-13
SEAT ELEMENT - DIAGNOSIS AND
TESTING, HEATED....................8G-13
SEAT ELEMENT - OPERATION, HEATED . . . 8G-13
SEAT HEATER SWITCH - DESCRIPTION,
DRIVER............................8G-11
SEAT HEATER SWITCH - DESCRIPTION,
PASSENGER........................8G-14
SEAT HEATER SWITCH - INSTALLATION,
DRIVER............................8G-13
SEAT HEATER SWITCH - INSTALLATION,
PASSENGER........................8G-15
SEAT HEATER SWITCH - OPERATION,
DRIVER............................8G-12
SEAT HEATER SWITCH - OPERATION,
PASSENGER........................8G-14
SEAT HEATER SWITCH - REMOVAL,
DRIVER............................8G-13
SEAT HEATER SWITCH - REMOVAL,
PASSENGER........................8G-15
SEAT MODULE - DESCRIPTION, HEATED . . 8E-21
SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED....................8E-22
SEAT MODULE - INSTALLATION, HEATED . . 8E-24
SEAT MODULE - OPERATION, HEATED....8E-21
SEAT MODULE - REMOVAL, HEATED.....8E-24
SEAT RISER - INSTALLATION, MANUAL . . 23-168
SEAT RISER - REMOVAL, MANUAL......23-167
SEAT SENSOR - DIAGNOSIS AND
TESTING, HEATED....................8G-14
SEAT SWITCH - DESCRIPTION, LEFT
POWER............................8N-16
SEAT SWITCH - DESCRIPTION, RIGHT
POWER............................8N-19
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED..............8G-12,8G-14
SEAT SWITCH - DIAGNOSIS AND
TESTING, LEFT POWER...............8N-17
SEAT SWITCH - DIAGNOSIS AND
TESTING, RIGHT POWER..............8N-19
SEAT SWITCH - INSTALLATION, LEFT
POWER............................8N-18
SEAT SWITCH - INSTALLATION, RIGHT
POWER............................8N-20
SEAT SWITCH - OPERATION, LEFT
POWER............................8N-17
SEAT SWITCH - OPERATION, RIGHT
POWER............................8N-19
SEAT SWITCH - REMOVAL, LEFT POWER . 8N-18
SEAT SWITCH - REMOVAL, RIGHT
POWER............................8N-20
SEAT SYSTEM - DESCRIPTION, HEATED . . 8G-10
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED
....................8G-11
SEAT SYSTEM - OPERATION, HEATED
....8G-10
SEAT TRACK - DESCRIPTION
...........8N-15
SEAT TRACK - DIAGNOSIS AND TESTING
. 8N-16
SEAT TRACK - INSTALLATION
..........23-168
SEAT TRACK - INSTALLATION
..........8N-16
SEAT TRACK - OPERATION
.............8N-15
SEAT TRACK - REMOVAL
.............23-168
SEAT TRACK - REMOVAL
..............8N-16
SEATBELT INDICATOR - DESCRIPTION
....8J-27
SEATBELT INDICATOR - OPERATION
......8J-28
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES
.....................9-26
SEATS - DESCRIPTION, POWER
.........8N-14SEATS - DIAGNOSIS AND TESTING,
POWER............................8N-15
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES.................9-28,9-36
SEATS - OPERATION, POWER..........8N-15
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES .........................9-27,9-35
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT . . 8Q-3
SECURITY INDICATOR - DESCRIPTION....8J-28
SECURITY INDICATOR - OPERATION.....8J-28
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT..............8Q-6
SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL LEVEL.................14-9
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL.............14-9
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL............14-10
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL..........................14-9
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-9
SENSE - DESCRIPTION, IGNITION
CIRCUIT............................8E-13
SENSE - OPERATION, IGNITION CIRCUIT . . 8E-15
SENSE - PCM INPUT - OPERATION, ASD . . . 8I-4
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - DESCRIPTION, AMBIENT
TEMP..............................8M-9
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-24
SENSOR - DESCRIPTION, CRANKSHAFT
POSITION..........................14-30
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-19
SENSOR - DESCRIPTION, FRONT
IMPACT............................8O-21
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - DESCRIPTION, INPUT SPEED . 21-143
SENSOR - DESCRIPTION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - DESCRIPTION, KNOCK........8I-11
SENSOR - DESCRIPTION, LINE
PRESSURE (LP)....................21-144
SENSOR - DESCRIPTION, MAP..........14-38
SENSOR - DESCRIPTION, OUTPUT
SPEED............................21-152
SENSOR - DESCRIPTION, OXYGEN.......14-40
SENSOR - DESCRIPTION, POSITION....21-209,
21-247
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-47
SENSOR - DESCRIPTION,
TRANSMISSION RANGE..............21-168
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE........21-170
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE...............8M-9
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-14
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-24
SENSOR - INSTALLATION, CRANKSHAFT
POSITION..........................14-32
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - INSTALLATION, FRONT
IMPACT............................8O-22
SENSOR - INSTALLATION, FRONT
WHEEL SPEED........................5-34
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT......................14-10
SENSOR - INSTALLATION, INPUT SPEED . 21-143
SENSOR - INSTALLATION, INTAKE AIR
TEMPERATURE
......................14-38
SENSOR - INSTALLATION, KNOCK
........8I-12
SENSOR - INSTALLATION, LINE
PRESSURE (LP)
....................21-144
SENSOR - INSTALLATION, MAP
.........14-40
SENSOR - INSTALLATION, OUTPUT
SPEED
............................21-152
KJINDEX 23
Description Group-Page Description Group-Page Description Group-Page

JEEP LIBERTY 2002
SPARE WHEEL & HARDWARE19-020-<8)
21-522~
23 .lLI
11
b
RACK & PINION10
~66~ -
24I14~
~2~
!
31~J~L2S--£3J
!;:;q)17
118-#~ I~
12~
/~004-09516 ~~'"
5~132616A-15~~
1 Wheel, Spare 14Steel 5GL65S4AAA 160.00 16 004 09907Alloy --
16x7Code WLD 10 Arm, Upper Control AiL 52088632AA m #2.0 128.00To 10-1-01 5GL67PAKAA 249.00 #W/Steering Knuckle Assy Removed Deduct 1.2 004 09522 c~From 10-1-01 5GL67PAKAB 24900 11 Bum~r, Control Arm AiL 52088684AB m 25.75 -
Code WND 5GL66PAKAB 260'00 12 Knuckle Assy, Steering R 52088652AA m #1.7 127.0017x7.5 .L 52088653AA m #1.7 127.00 1 Gear Assy, SteeringCode WGO 5HW90ZDRM 249.00 #/ncludes R&R Brake Rotor and Hub & Bearing Assy, 2.4L Eng 52128588M m #1.9 484.00Code WGR 5HW90AFMAA 24900 R&R Both Sides 3.2 37L Eng 52128518M m #1.9 459.002 Jack 52059104 83:35 13 Joint, Lower Balll] AiL 5069161AB m 2.0 27.50 #W/4WD Add 3.63 Wrench, Lug 52059478AA 12.85" l]/nc/uded w/Steering Knuckle Assy 2 Boot, Steering Gear1J AiL 5O72446M m 57.104 Bracket, Jack 52059369M 16.35!114Arm,LowerControl R 52088636AD m#2.2 117.00 3Bolt,Mountingl] AiL 6506517M 7.505 Label, Jack Instructions-See InforrnatJon Labels SectJon L 52088637AD m #2.2 117.00 4 Nut, MountJng:~ AiL 6504707 2.456 Bracke~ Spare. Wheel 55155933AB 59.10 #Includes R&R Bushings, w/Steering Knuckle 5 Bushing, Steering Gear1J AiL 52038783AB 15.20Cover, :opare Tire 5JG141X7M Removed Deduct.9 l1/nc/uded w/Steering Gear AssyAiL 52088746M m 12.25 6 Rod, Outer Tie R 5O72444M 46.70AiL 52088649AC m L 5072445M 46.70
AIL 6507080AA18 Bolt, Lower Carn (2/Side) AiL 6507321M19 Nut, Absorber AiL 6506443M 1.5020 Retainer, Absorber AiL 52089069M 2.25 2.4L ENG21 Mount, Absorber R 52128532AA m #1.8 91.70L 52128533AA m #1.8 91.7022 Isolator, Upper Spring AiL 52088686M m #1.8 16.25 423 Springl] AiL 52088625M m #1.8 35.75~.tr24 Absorber, Shock11 AiL 52088650AB m #1.8 36.95 111Additional Parts &lor Dealer Contact Required 0 3125 Isolator, Lower Spring AiL 52088686M m #1.8 16.25 -
I #R&R One Side Complete, Includes R&R ClevisAbsorber, w/Steering Knuckle Assy Removed Deducr ~.7, R&R Both Sides 3.426 Clevis, Absorber AiL 52088748AC m #.6 49.75#W/Steering Knuckle Assy Removed Deduct.4
29\",~~-l 004-09908
27 Retainer, Stab Bar AiL 52088631M m #.3 9.70 I128 Bushing, Slab Bar AiL 52088778M m #.3 4.60 c 004 09909#R&R One Side Complete, Not Included in O/H! -
29 Link, Stab Bar Ail 52088662AB m #.3 43.75PS.#Not Included in O/H 1 ump, teerlng30 Bar, Stabilizer 52088660M m #.8 98.25 2 Pulley, ~ump#Includes R&R Stab Bar Links, Bushings & Retainers 3 Reservoir, Pu~pNot Included in O/H 4 Cap, Reservoir.Bracket, Reservoir
6
~",,3
2
m .3m .3
52
Use Procedure Explanation 11 with the following text.
R&I Suspension/Sub.Frame Assy2WD m#2.74 WD m #3.6#Not Included in O/H SuspensionO/H SuspensionOne Side , R/Lm 4.7Both Sides. m 8.4Bleed Brake Systemw/ABS m .6w/oABS m .3AdjustFrontAlignment m 1.5NOTE 1: R&UR&R or O/H Does Not include alignment or bleedbrake system.
NOTE 2: All Parts in this section are included in overhaulunless noted otherwise.
/1
I'~~II::It
52088711AA m 1.7 130.0053031722AA m 21.6052088713AA m .5 40.2552128513AA 10.4552088874AD 43.4552088722AC m .8 163.0052088718AC m 23.4552128561AA m .9 174.00
5
~L-7 Cooler, SteeringR&I Axle Housing Assy m 3.0R&I Outer Axle Shaft Assy R/Lm #1.5#WlSteering Knuckle Assy Removed Deduct .93.7L ENG
4004-09906
004-09520
1 Nut, Axle AiL 6506454AA m 8.502 Rotor, Brake AiL 52128247AA m #.9 104.00#R&R Both Sides 1.63 Caliper, Brake R 5066422AA m #.5 182.00 IL 5066423AA m #.5 182.00 I4 Bracket, Caliper Mounting AIL 5019986AA m #.5 42.50#R&R One Side Complete, w/Brake Rotor RemovedDeduct .3, R&R Both Sides .85 Pad Set, Brake 5066427AA m #1.0 128.00#Deduct .5 for Each Brake Caliper Removed6 Hub & Bearingw/ABS R 52128692AA m #1.3 259.00L 52128693AA m #1.3 259.00w/o ABS AiL 52128352AB m #1.3 259.00I#Includes R&R Brake Rotor, R&R Both Sides 2.47 Stud, Wheel AiL 6O36388AA m 2.958 Sensor, Front ABS-See ABSIBrakes Section9 Hose, Front Brake R 52128312AA m #.3 18.35L 52128311AA m #.3 18.35#W/Caliper Removed Deduct .2
567Procedure Explanation Pages Must Be Used with the Above Text for an Accura'~ Damage Report.Comments or suggestions? Need assistance? Call 1-800-854-7030 or 858/578-6550, Ext 8220. Fax 1-888-256-7969 or 858/549-0629.CH
R&I Steering Gear Assy m #1.7#W/4WD Add 3.6
NOTE: R&R Does Not include adjust wheel alignment.~
6~9 2
67rl1
~'~
3 2,
51 Shaft Assy, Outer Axle f IA
~,::;~~~~2.4LEng R 5066022AA m#1.5 994.00cJ1y L 5066023AA m #1.5 1155.00'
3.7L Eng R 5066020AA m #1.5 1020.00L 5066021AA m #1.5 1155.00#WlSteering Knuckle Assy Removed Deduct .92 Boot Kit, Inner1j AiL 5066024AA m 26 203 Boot Kit, Outer1j AiL 5066025AA m 25:50~/ncluded w/Outer Axle Shaft Assy 004-09524
Bracket, Mountin~2.4L Eng R 52059472AB m 81.85 1 PumplReservoir. Assy, Steering 52088710AA m 2.4 130.00L 52059473AB m 54.50 2 Cap, Reservolr1j 52088956AA 27.453.7L Eng R 52059464AB m 81.85 ~/ncluded w/Steering Pumf)/ReseIVo;r AssyL 52059465AB m 30.85 I 3 Pulley, Pump 5:3010258AC m #.3 20.25