garage door opener JEEP LIBERTY 2002 KJ / 1.G Workshop Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 2002, Model line: LIBERTY, Model: JEEP LIBERTY 2002 KJ / 1.GPages: 1803, PDF Size: 62.3 MB
Page 515 of 1803
(4) Using hand pressure, pull the cargo lamp
switch toward the outside of the lamp unit housing
until it unsnaps from the housing.
(5) Continue sliding the cargo lamp switch away
from the terminal pins and out of the lamp unit
housing.
INSTALLATION
(1) Align the terminal receptacles in the cargo
lamp switch with the terminal pins of the lamp unit
housing (Fig. 6).
(2) Using hand pressure, push the cargo lamp
switch toward the terminals of the lamp unit housing
until it snaps into the housing.
(3) Reinstall the cargo lamp unit onto the head-
liner near the rear roof header. (Refer to 8 - ELEC-
TRICAL/LAMPS/LIGHTING - INTERIOR/CARGO
LAMP UNIT - INSTALLATION).
(4) Reconnect the battery negative cable.
CARGO LAMP UNIT
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Using a trim stick or another suitable wide
flat-bladed tool, gently pry between the flange
around the edge of the cargo lamp unit housing and
the headliner to release the metal snap clip on each
side of the housing from the receptacles in the rear
roof header (Fig. 7).(3) Pull the cargo lamp unit away from the head-
liner far enough to access and disconnect the rear
body wire harness connector for the lamp from the
connector receptacle on the lamp unit housing.
(4) Remove the cargo lamp unit from the mounting
hole in the headliner.
INSTALLATION
(1) Position the cargo lamp unit to the mounting
hole in the headliner.
(2) Reconnect the rear body wire harness connec-
tor for the cargo lamp to the connector receptacle on
the lamp unit housing.
(3) With the finger depression in the cargo lamp
lens oriented towards the rear of the vehicle, position
the cargo lamp unit housing into the headliner
mounting hole and align the metal snap clip on each
side of the housing with their receptacles in the rear
roof header (Fig. 7).
(4) Using hand pressure, press upward firmly and
evenly on both ends of the cargo lamp unit until both
snap clips are fully engaged in their receptacles.
(5) Reconnect the battery negative cable.
COMPASS MINI-TRIP
ILLUMINATION BULB
REMOVAL
The Compass Mini-Trip Computer (CMTC) in the
overhead console includes either two or three incan-
descent illumination bulb and bulb holder units.
Three bulbs are used only on models that also fea-
ture the optional Universal Garage Door Opener
(UGDO).
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE SUPPLEMENTAL RESTRAINT
SYSTEM BEFORE ATTEMPTING ANY STEERING
WHEEL, STEERING COLUMN, DRIVER AIRBAG,
PASSENGER AIRBAG, SEAT BELT TENSIONER,
FRONT IMPACT SENSORS, SIDE CURTAIN AIRBAG,
OR INSTRUMENT PANEL COMPONENT DIAGNOSIS
OR SERVICE. DISCONNECT AND ISOLATE THE
BATTERY NEGATIVE (GROUND) CABLE, THEN
WAIT TWO MINUTES FOR THE SYSTEM CAPACI-
TOR TO DISCHARGE BEFORE PERFORMING FUR-
THER DIAGNOSIS OR SERVICE. THIS IS THE ONLY
SURE WAY TO DISABLE THE SUPPLEMENTAL
RESTRAINT SYSTEM. FAILURE TO TAKE THE
PROPER PRECAUTIONS COULD RESULT IN ACCI-
DENTAL AIRBAG DEPLOYMENT AND POSSIBLE
PERSONAL INJURY.
Fig. 7 Cargo Lamp Unit Remove/Install
1 - CARGO LAMP UNIT
2 - HEADLINER
3 - TRIM STICK
8L - 74 LAMPS/LIGHTING - INTERIORKJ
CARGO LAMP SWITCH (Continued)
Page 516 of 1803
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the overhead console from the head-
liner. (Refer to 8 - ELECTRICAL/OVERHEAD CON-
SOLE - REMOVAL).
(3) From the back of the unit, use a small thin-
bladed screwdriver to rotate the compass mini-trip
illumination bulb holder counterclockwise about 30
degrees on the circuit board (Fig. 8).
(4) Pull the compass mini-trip illumination bulb
holder and bulb unit straight out of the circuit board
bulb mounting hole.
INSTALLATION
The Compass Mini-Trip Computer (CMTC) in the
overhead console includes either two or three incan-
descent illumination bulb and bulb holder units.
Three bulbs are used only on models that also fea-
ture the optional Universal Garage Door Opener
(UGDO).
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE SUPPLEMENTAL RESTRAINT
SYSTEM BEFORE ATTEMPTING ANY STEERING
WHEEL, STEERING COLUMN, DRIVER AIRBAG,
PASSENGER AIRBAG, SEAT BELT TENSIONER,
FRONT IMPACT SENSORS, SIDE CURTAIN AIRBAG,
OR INSTRUMENT PANEL COMPONENT DIAGNOSIS
OR SERVICE. DISCONNECT AND ISOLATE THE
BATTERY NEGATIVE (GROUND) CABLE, THEN
WAIT TWO MINUTES FOR THE SYSTEM CAPACI-
TOR TO DISCHARGE BEFORE PERFORMING FUR-
THER DIAGNOSIS OR SERVICE. THIS IS THE ONLY
SURE WAY TO DISABLE THE SUPPLEMENTALRESTRAINT SYSTEM. FAILURE TO TAKE THE
PROPER PRECAUTIONS COULD RESULT IN ACCI-
DENTAL AIRBAG DEPLOYMENT AND POSSIBLE
PERSONAL INJURY.
CAUTION: Always use the correct bulb size and
type for replacement. An incorrect bulb size or type
may overheat and cause damage to the lamp, the
socket and/or the lamp wiring.
(1) Align the compass mini-trip illumination bulb
holder and bulb unit with the circuit board bulb
mounting hole.
(2) Insert the compass mini-trip illumination bulb
holder and bulb unit straight into the circuit board
bulb mounting hole until it is firmly seated (Fig. 8).
(3) Using a small thin-bladed screwdriver, rotate
the compass mini-trip illumination bulb holder clock-
wise about 30 degrees on the circuit board.
(4) Reinstall the overhead console onto the head-
liner. (Refer to 8 - ELECTRICAL/OVERHEAD CON-
SOLE - INSTALLATION).
(5) Reconnect the battery negative cable.
COURTESY LAMP BULB
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE SUPPLEMENTAL RESTRAINT
SYSTEM BEFORE ATTEMPTING ANY STEERING
WHEEL, STEERING COLUMN, DRIVER AIRBAG,
PASSENGER AIRBAG, SEAT BELT TENSIONER,
FRONT IMPACT SENSORS, SIDE CURTAIN AIRBAG,
OR INSTRUMENT PANEL COMPONENT DIAGNOSIS
OR SERVICE. DISCONNECT AND ISOLATE THE
BATTERY NEGATIVE (GROUND) CABLE, THEN
WAIT TWO MINUTES FOR THE SYSTEM CAPACI-
TOR TO DISCHARGE BEFORE PERFORMING FUR-
THER DIAGNOSIS OR SERVICE. THIS IS THE ONLY
SURE WAY TO DISABLE THE SUPPLEMENTAL
RESTRAINT SYSTEM. FAILURE TO TAKE THE
PROPER PRECAUTIONS COULD RESULT IN ACCI-
DENTAL AIRBAG DEPLOYMENT AND POSSIBLE
PERSONAL INJURY.
(1) Disconnect and isolate the battery negative
cable.
(2) Support the courtesy lamp unit housing with
one hand while firmly grasping the flange on the
outer circumference of the lens with the other hand,
then pull the lens straight down to unsnap it from
the housing (Fig. 9).
(3) Pull the courtesy lamp bulb straight out of the
lamp unit socket.
Fig. 8 Compass Mini-Trip Illumination Bulb
Remove/Install
1 - OVERHEAD CONSOLE
2 - BULB & HOLDER (3)
3 - COMPASS MINI-TRIP COMPUTER
KJLAMPS/LIGHTING - INTERIOR 8L - 75
COMPASS MINI-TRIP ILLUMINATION BULB (Continued)
Page 601 of 1803
(3) Remove the compass mini-trip computer from
the overhead console.
INSTALLATION
(1) Install the compass mini-trip computer in the
overhead console. Align the compass mini-trip com-
puter guides on the housing with the grooves of the
console.
(2) Install the mounting screws and install the
map lamp wire connector on the compass mini-trip
computer. Make sure the LOOP of wire that was
clipped into the compass mini-trip computer module
housing is properly clipped into the new module
before the console is placed back into the headliner.
(3) Install the overhead console, refer to Console
Installation in this section.
UNIVERSAL TRANSMITTER
DESCRIPTION
On some KJ models a Universal Transmitter trans-
ceiver is standard factory-installed equipment. The
universal transmitter transceiver is integral to the
Compass Mini-Trip Computer (CMTC), which is
located in the overhead console. The only visible com-
ponent of the universal transmitter are the three
transmitter push buttons (Fig. 7) centered between
the four CMTC push buttons located just rearward of
the CMTC display screen in the overhead console.
The three universal transmitter push buttons are
identified with one, two or three light indicators so
that they be easily identified by sight or by feel.
Each of the three universal transmitter push but-
tons controls an independent radio transmitter chan-
nel. Each of these three channels can be trained totransmit a different radio frequency signal for the
remote operation of garage door openers, motorized
gate openers, home or office lighting, security sys-
tems or just about any other device that can be
equipped with a radio receiver in the 286 to 399
MegaHertz (MHz) frequency range for remote opera-
tion. The universal transmitter is capable of operat-
ing systems using either rolling code or non-rolling
code technology.
The CMTC module displays messages and a small
house-shaped icon with one, two or three dots corre-
sponding to the three transmitter buttons to indicate
the status of the Universal Transmitter.
The Universal Transmitter cannot be repaired, and
is available for service only as a unit with the CMTC
module. This unit includes the push button switches
and the plastic module and display lens. If any of
these components is faulty or damaged, the complete
CMTC module must be replaced.
OPERATION
The universal transmitter operates on a non-
switched source of battery current so the unit will
remain functional, regardless of the ignition switch
position. For more information on the features, pro-
gramming procedures and operation of the universal
transmitter, see the owner's manual in the vehicle
glove box.
DIAGNOSIS AND TESTING - UNIVERSAL
TRANSMITTER
If the Universal Transmitter is inoperative, but the
Compass Mini-Trip Computer (CMTC) is operating
normally, see the owner's manual in the vehicle glove
box for instructions on training the universal trans-
mitter. Retrain the universal transmitter with a
known good transmitter as instructed in the owner's
manual and test the universal transmitter operation
again. If the unit is still inoperative, replace the
faulty universal transmitter and CMTC module as a
unit. If both the universal transmitter and the CMTC
module are inoperative, refer toDiagnosis and
Testing the Compass Mini-Trip Computerin this
section for further diagnosis. For complete circuit
diagrams, refer toOverhead Consolein Wiring
Diagrams.
STANDARD PROCEDURE
STANDARD PROCEDURE - ERASING
TRANSMITTER CODES
To erase the universal transmitter codes, simply
hold down buttons 1 and 3 until the two green dots
below the house symbol begin to flash.
Fig. 7 Overhead Console With Universal Transmitter
8M - 8 MESSAGE SYSTEMSKJ
COMPASS/MINI-TRIP COMPUTER (Continued)
Page 1788 of 1803
JEEP LIBERTY 2002
4'M"anuaIWindows R 55360036AA #.3 66.70L 55360027AA #.3 66.70#WlDoor Glass RemovedPower Windows1! R 55360034AA #.3 46.35L 55360035AA #.3 46.351]Additional Paris &/or Dealer Col'ltact RequiredMotor, Window Ail N.A #.3 0.00#R&R One Side Complete, w/D'~or Glass RemovedHandle, Window R/L FW80WI_5 6.95
~5
~
REAR DOOR Cont'd
Refinish UpperHinge-~~ .Refinish Lower Hinge R&I Outside Handle Assy #/ncludes R&I Trim PanelR/L .3R/L .3AiL #.5
2
1
11
..PUse Procedure Explanations 17 and 28 with the following tex/.3004-09564~
SHEET METAL121 Console, Overheadw/Sunroofw/o SunroofModule, Consolew/Garage Door Opener2 Lamp, Consolew/Sunroof Switchw/o Sunroof Switch3 Lens, LampI 4 Wiring Console5 Bulb, 'Console (2)Switch, SunroofSwitch, Reading Lamp
WA951L2AA5O14271AA
4760145BF
WA901L2AAPB83TL2AB55196755AA4760644LOOOO1925GM78TL2AA4685445
.4 00.45.4 189.00
315.00
.3 66.35.3 78.20.1 6.50.3 20.85.1 1.9575.105.00
3.5
1.0~7
e-d r
10~
9-d
Refinish RoofOulside Add 10 R&R Roof Panel
To Drill for & Install Luggage Rack5
~12 3
~"
3
ROOF LUGGAGE RACK
4004-09561R&I Luggage RackAssy .5R&R Luggage Rack Complete (Includes R&I) 8
NOTE: All Parts in this section are included in R&R LuggageRack Complete unless noted otherwise.
#.3 5O.35l#.3 45:75-#.3 81.75 1 Panel Roof#.3 81.75 w/Sunroof 55176995AB #16.5 215.00.2 875 wlo Sunroof 55176994AB #15.5 155.002.75 #Does Not Inc/l~de R&R Quslter Glass2'95 2 Panel, Front Header 55177022AA 1.0 22.952.95 3 Bow, No.1 Roof15.70 wlo Sunroof 553602E:1AA 1.0 18.102:85 4 Bow, No.2 Roof 5517699:~AA 1.0 18.101AA 1.0 18.102.8510.00 EXTERIOR TRIM~
I ~-
T ~;:../ 4~~b -8 11--dJ'~~:;;f~~::::::=~- 3 6
12 '
004-09559
1 Latch, DoorManual Locks R 55177046ABL 55177047ABPower Locks R 55177044ABL 55177045AB#Wrrrim Panel Removed2 Striker, Latch AiL 4780607AA3 Spacer, Striker AiL 45202894 Rod, Inside Lock R 5072360AAL 5O72361AACover, Latch AiL 5014395AA5 Rod, Inside Handle R 5072356AAL 5072357AA6 Rod, Lock Knob R 55360464AAL 55360465AA7 Handle, Outside R 55360334AB #.2 36.00 IL 55360335AB #.2 36.00#Wrrrim Panel Removed8 Hinge, Upper AiL 55177030AA #.2 26.259 Hinge, Lower AiL 55177030AA #.2 26.25#W/Door & Upper Center Trim Panel Removed10 Check, Door AiL 55177036AB #.2 26.50#Wrrrim Panel Removed11 Seal, Lower Door AiL 55235930AA .2 9.0012 Weatherstrip, Door1] AiL 5GU15WL5AA .6 57.201]Addilional Paris &/or Dealer Contact Required
"--"~~~~-~,'" -~$ --.""",," _,,;-r-:>"'-~,,--'"~~ -s:",,- -~-'"",," 6"",-""~-/-. '- /,'--=, I'
1
'"'.."
.4 90.25
13.1013.1012.4512.45
#.3 59.50#.3 59.50
0.000.00
0.000.00
.8 409.00
#.3 59.50
#.3 59.50
GLASS & PARTS1 Moulding, Roofw/Roof~ack
wiD Roof Rack
.5.5.5.5
54.2054.2066.20166.20
1-{12
R 553601i'4AAL 553601i'5AAR 553601i'6AAL 553601i7AA
9
p
R&I Headliner.2.8v
,~,17=~'7~
t'...'"004-09932 ""',Ii;-
1 Rail, Luggage Rack AIL 55360419ABCover, luggage RackFront R 55360424AAL 55360425AA3 Rear R 55360426AAIL 55360427AA4 Rail, Luggage Rack CrossFront 55360526AARear 55156586AA#R&R Both .4I 5 Cap, Screw Cover (2iSidelAIL 55156591AA6 Cap, Cross Rail End (2JSide Ail 55156597AA7 Cover, Cross RailFront SJA18ZSPAARear SJA19ZSPAA8 Carrier Assy, CargoRenegade Model 5HZ66ZSPAB9 Rail, Front Cross~Renegade Model 55360526AB10 Rail, Rear Cross1\Renegade Model 55156586AB~fncfuded w/Cargo Carrier Assy#R&R Both.411 Isolator, Cargo Carrierw/Sunroof
WiD Sunroof
3
2, ,
~
6
R 55156592ABL 55156593ABR 55156594ABL 55156595AB
9.709.709.709.70.J/004-09563
LIGHT BAR004-09930
1 Glass, Rear DoorChrysler-Tinted R 55360378ABL 55360379ABNAGSGreen R/L DDO9986-7GTYPrivacy R/L DD10064-3YPY2 Glass/Channel, GlassChrysler-TintedGreen R 55235876ABL 55235877ABPrivacy R 55360172ABL 55360173ABNAGSGreen R/L DVO9993-4GTNPrivacy R/L DV10Q65-6YPY#W/Door Glass Removed3 Weatherstrip, Frt Pillar R/L 55235860AA4 Weatherstrip, Outer Belt R 55235872AAL 55235873AA5 Weatherstrip, Inner Belt R 55235886ABL 55235887AB
1.0 195.001.0 210.00
1.0 403.651.0 411.85
2
3~45
~~6
004-09933
1 Cover, Light Bar2 lamPILight Bar (4)3 Bulb 4l4 Cover, ens5 Bar, Support6 Harness, Light Bar
5HZO1ZSPAB52112063ABLOOO90065HZO7RXFAB5083967 AA52112062AA
1 Headliner1l Iw/Sunroolw/Side Air Bag OY911 L2AA 2.8 627.00'wlo Side Air Bag UY731L2AA 2.8 800.00wlo Sunroofw/Side Air Bag UY87TL2AA 2.8 627.00wlo Side Air Bag' UY71TL2AA 2.8 735.001]Additional Parts &/or Dealer Contact Required2 Handle, Grab R UY681L2AA .1 0.00L UY691L2AA .1 0.00#.3 139.00'Lamp, Cargo 5FT10TL2 43.50#.3 139.00 Lens, ~argo Lamp. 55196755AA 6.50#.3 145.00 Moulding, Rear Intenor#.3 145.00 Slate Gray 5GP80WL5AC 11.50Taupe 5GP80XDVAC 11.50#.3 0.00 Clip, Mldg Retainer (!9) 6506311 AA .45#.3 737.10
.2 13.95.2 24.751R&I Overhead Console .2.2 24.7520.25 NOTE: All Parts in this section are included in R&R Overhead20.25 Console unless noted otherwise.
Labor Times Shown are for Replacement with New OEM Undamaged Parts on New Undamaged Vehicles.Comments or suggestions? Need assistance? Call 1-800-854-7030 or 8581578-6550, Ext 8220. Fax 1-888-256-7969 or 8581549-0629.574
165.00143.0010.000.00160.0040.35
2,