ECO mode KIA BORREGO 2017 Owner's Guide

Audio system
556Skipping Prompt Messages While prompt message is being stat- ed
Shortly press the button on
the steering wheel controls. The prompt message is immediately ended and the beep tone will sound.
After the “Ding”, say the voice com-mand.
Re-starting Voice Recognition
While system waits for a command
Shortly press the button on the
steering wheel controls.
The command wait state is immedi- ately ended and the beep tone will
sound. After the “Ding”, say the voicecommand. Ending Voice Recognition
While Voice Recognition is operating

Press and hold the button on
the steering wheel controls.
While using voice commands, pressing some steering wheel con-
trols or some different buttons will
end voice command.
When the system is waiting for a voice command, say “cancel” or
“end” to end voice command.
When the system is waiting for a voice command, press and hold
the button on the steering
wheel controls to end voice com-mand.
✽✽ NOTICE
Voice Recognition and Phonebook
Tips
The Kia Voice Recognition System
may have difficulty understanding
some accents or uncommon names.
When using Voice Recognition to
place a call, speak in a moderate
tone, with clear pronunciation.
To maximize the use of Voice
Recognition, consider these guide-
lines when storing contacts:
 Do not store single-name entries (e.g., “Bob”, “Mom”, etc.). Instead,
always use full names (including
first and last names) for these con-
tacts.
 Do not use special characters (e.g., '@', '-', '*', '&', etc.).
 Do not use abbreviations (i.e., use "Lieutenant" instead of "Lt.") or
acronyms (i.e., use "County
Finance Department" instead of
"C. F. D."; Be sure to say the name
exactly as it is entered in the con-
tacts list

Driving your vehicle
8
6
Starting the gasoline engine
1. Make sure the parking brake is
applied.
2. Place the transaxle shift lever in P (Park). Depress the brake pedal
fully.
You can also start the engine
when the shift lever is in the N(Neutral) position.
3. Turn the ignition switch to START and hold it there until the engine
starts (a maximum of 10 sec-
onds), then release the key.
It should be started without
depressing the accelerator pedal.
4. Do not wait for the engine to warm up while the vehicle remains sta-
tionary.
Start driving at moderate engine
speeds. (Steep accelerating and
decelerating should be avoided.)
CAUTION
If the engine stalls while you are
in motion, do not attempt tomove the shift lever to the P (Park) position. If traffic androad conditions permit, you mayput the shift lever in the N(Neutral) position while the vehicle is still moving and turnthe ignition switch to the STARTposition in an attempt to restart the engine.
CAUTION
Do not engage the starter for more than 10 seconds. If theengine stalls or fails to start, wait 5 to 10 seconds before re-engaging the starter. Improperuse of the starter may damage it.
Do not turn the ignition switch to the START position with theengine running. It may dam-age the starter.

619
Driving your vehicle
D (Drive)
This is the normal forward driving
position. The transaxle will automati-cally shift through a 5 (or 8)-gear
sequence, providing the best fuel
economy and power.
For extra power when passing anoth-
er vehicle or climbing grades,
depress the accelerator fully, at which
time the transmission will automati-
cally downshift to the next lower gear.
✽✽NOTICE
Always come to a complete stop
before shifting into D (Drive).
Manual mode
Whether the vehicle is stationary or
in motion, manual mode is selected
by pushing the shift lever from the D
(Drive) position into the manual gate.
To return to D (Drive) range opera-
tion, push the shift lever back into the
main gate.
In manual mode, moving the shift
lever backwards and forwards will
allow you to make gearshifts rapidly.
In contrast to a manual transmission,
the manual mode allows gearshifts
with the accelerator pedal depressed. Up (+) : Push the lever forward
once to shift up one gear.
Down (-) : Pull the lever backwards once to shift down one
gear.
✽✽NOTICE
 In manual mode, the driver must execute upshifts in accordance
with road conditions, taking care
to keep the engine speed below the
red zone.
 In manual mode, only the 5 (or 8) forward gears can be selected. To
reverse or park the vehicle, move
the shift lever to the R (Reverse)
or P (Park) position as required.
 In manual mode, downshifts are made automatically when the
vehicle slows down. When the
vehicle stops, 1st gear is automati-
cally selected.
 In manual mode, when the engine rpm approaches the red zone shift
points are varied to upshift auto-
matically. (Continued)
OHM056005

625
Driving your vehicle
This mode is used when driving on slippery roads such as
snowy and rainy roads at normal speed.
Maximum speed: 80 km/h (50 mph)
2H
(Rear-wheel drive)
✽✽ NOTICE
4WD transfer has a time delay for a few seconds until the actual shift is made after turning the transfe r shift knob.
When the 4WD transfer mode is shifted, it may cause mechanical noise. It is not a mechanical failur e but a normal
condition.
Part-Time 4WD (if equipped)
Transfer mode Selection button Indicator light Description
This mode is used when driving on normal roads and
highway.
4H
(High-speed
4-wheel drive)
This mode is used when increased traction is required,
such as climbing or descending hills, driving off-roads,
and towing a vehicle.
Maximum speed: 40 km/h (25 mph)
4L
(Low-speed
4-wheel drive)
44 WW DD
H
H II
4WD
HI
4WD
LOW
44 WW DD
L
L OO WW
(not illuminated)
(illuminated)(illuminated)
CAUTION
When you stop the vehicle to transfer the shift knob, wait until the corresponding indicator light turns on or off to depart. If the vehicle moves before the transfer is completed, the vehicle may be damaged.

Driving your vehicle
26
6
Part-time 4WD knob operation
2H ↔↔
4H
Turn the transfer knob from the 2H mode to 4H mode or 4H mode to 2H
mode at the speed below 80 km/h
(50 mph). It is not necessary to put
the shift lever into the N (Neutral)
position. Perform this operation when
driving straight. There will be a few
seconds of time delay before shifting
into the desired mode.
If the weather is extremely cold (- 15°C /5°F) and the engine is not
heated, transfer from 2H mode to 4H
mode when the vehicle is stopped or
at low speed. 4H
↔
↔
4L
1. Stop the vehicle.
2. Put the shift lever into the N (Neutral) position.
3. Turn the transfer knob to the 4H or 4L position.
4. Before shifting to other ranges from the N (Neutral) position, wait
for the corresponding indicator
light to turn on or off in the cluster.
✽✽ NOTICE
If the mode is not shifted like the
previous instructions, it will not
transfer into the selected mode and
the corresponding indicator light
will continuously blink.
OHM058010N
OHM058011
CAUTION
Always check the 4WD shift knob and cluster to see if thesystem has been activated unintentionally.
Do not speed over 80 km/h (50 mph) in the 4H mode and 40km/h (25 mph) in the 4L mode.

627
Driving your vehicle
This mode is used when driving on slippery roads, such as
snowy and rainy roads at normal speed.
Maximum speed: 80 km/h (50 mph)
AUTO
(Automatic
4-wheel drive)
✽✽ NOTICE
4WD transfer has a time delay for a few seconds until the actual shift is made after turning the transfe r shift knob.
When the 4WD transfer mode is shifted, it may cause mechanical noise. It is not a mechanical failur e but a normal
condition.
Full-Time 4WD Operation (if equipped)
Transfer mode Selection button Indicator light Description
This mode is used when driving on normal roads and
highway.
The engine power is distributed to all four wheels auto-
matically without the driver's intervention in accordance
with the road conditions and driving conditions.
4H
(High-speed
4-wheel drive)
This mode is used when ncreased traction is required,
such as climbing or descending hills, driving off-roads,
and towing a vehicle.
Maximum speed: 40 km/h (25 mph)
4L
(Low-speed
4-wheel drive)
44 WW DD
H
H II
4WD
HI
4WD
LOW
44 WW DD
L
L OO WW
(not illuminated)
(illuminated)(illuminated)
CAUTION
When you stop the vehicle to transfer the shift knob, wait until the corresponding indicator light turns on or off to depart. If the vehicle moves before the transfer is completed, the vehicle may be damaged.

Driving your vehicle
28
6
Full-time 4WD knob operation
AUTO ↔↔
4H
Turn the transfer knob from the
AUTO mode to 4H mode or 4H mode
to AUTO mode at the speed below
80 km/h (50 mph). It is not necessary
to put the shift lever into the N
(Neutral) position. Perform this oper-
ation when driving straight. There will
be a few seconds of time delay
before shifting into the desired mode.
If the weather is extremely cold (- 15°C/5°F) and the engine is not
heated, transfer from AUTO mode to
4H mode when the vehicle is
stopped or at low speed. 4H
↔
↔
4L
1. Stop the vehicle.
2. Put the shift lever into the N (Neutral) position.
3. Turn the transfer knob to the 4H or 4L position.
4. Before shifting to other ranges from the N (Neutral) position, wait
for the corresponding indicator
light to turn on or off in the cluster.
✽✽ NOTICE
If the mode is not shifted like the
previous instructions, it will not
transfer into the selected mode and
the corresponding indicator light
will continuously blink.
OHM058012N
OHM058013L
CAUTION
Always check the 4WD shift knob and cluster to see if thesystem has been activated unintentionally.
Do not speed over 80 km/h (50 mph) in the 4H mode and 40km/h (25 mph) in the 4L mode.

Driving your vehicle
30
6
You must consciously take the
effort to learn how to corner in a
4WD vehicle. Do not rely on your
experience in conventional 2WD
vehicles in choosing safe cornering
speed in 4WD mode. For starters,
you must drive more slowly in
4WD.
Drive carefully off-road because your vehicle may be damaged by
rocks or roots of trees. Become
familiar with the off-road conditions
where you are going to drive
before you begin driving. Always hold the steering wheel firm-
ly when you are driving off-road.
Make sure all passengers are wearing seat belts. If you need to drive in the water,
stop your vehicle, set your transfer
to the 4L mode and drive at lessthan 8 km/h (5 mph).
WARNING - 4WD
Reduce speed when you turn
corners. The center of gravity of
4WD vehicles is higher than
that of conventional 2WD vehi-
cles, making them more likely to
roll over when you turn cornerstoo fast.
WARNING - Wind danger
If you are driving in heavy wind,
the vehicle's higher center of
gravity decreases your steering
control capacity and requires
you to drive more slowly.
WARNING - Driving
through water
Drive slowly. If you are driving
too fast in water, the water can
get into the engine compart-ment and wet the ignition sys-
tem, causing your vehicle to
suddenly stop. If this happens
and your vehicle is in a tilted
position, your vehicle may roll
over.
WARNING - Steering wheel
Do not grab the inside of the
steering wheel when you are
driving off-road. You may hurt
your arm by a sudden steering
maneuver or from steeringwheel rebound due to impact
with objects on the ground. You
could lose control of the steer-ing wheel.
OHM056102L

Driving your vehicle
50
6
To go to the N (Normal) mode, press
the bottom part of the switch. Also, if
the vehicle speed is over 60 km/h
(38mph) or drives over 10 secondsat the speed of about 45 km/h
(28mph), the vehicle will lower itself
to the N (Normal) mode. LO (Low) - Loading mode
The rear part of the vehicle is low-
ered to make it easy to load or
unload cargo.
With the engine running press the
bottom part of the switch. The LO
(Low) mode activates only when the
vehicle is not moving. The indicator
blinks when the system is adjusting
itself to the LO (Low) mode. Whenthe adjustment is completed (about
40mm (2 in.) lowered) the indicator
will illuminate at LO (Low) on the
LCD display.To go to the N (Normal) mode, press
the top part of the switch. Also, if the
vehicle speed is over 2 km/h (1
mph), the vehicle will lift itself to the
N (Normal) mode.
✽✽
NOTICE
The ALS will adjust the rear height
of the vehicle according to the load
and number of passengers when the
ignition switch is in the ON position
or when the engine is on.
OHM056028L

659
Driving your vehicle
To operate the LDWS, press the
switch with the ignition in the ON
position. The indicator illuminates
white on the cluster.
To cancel the LDWS, press LDWS
button again. The indicator on the
cluster will go off.If you select this symbol, the LDWS
mode on the LCD display will appear.
If your vehicle leaves the lane when
the LDWS is operating and vehicle
speed exceeds around 60km/h, the
warning operates as follows:1. Visual warning
If you leave a lane, the lane you
cross will blink (yellow) and LDWS
indicator will blink green on LCD dur-
ing max 3 seconds.
OHM056105L
OHM056107L
OHM056106L
■Left lane departure warning
■Right lane departure warning