lock KIA CARNIVAL 2007 Workshop Manual

N(Neutral) for manual transaxle, P(Park) for automatic transaxle.
2. Door position
If the power sliding door is operated while the door is in slightly- opened position (less than 300mm), the door is
automatically opened fully. If the power sliding door is operated while the door is in slightly- opened position (more
than 300mm), the door is automatically closed completely.
3. If the door handle is pulled from inside or outside while the door is locked or child safety lock is engaged, the
power sliding door is not opened.

6Detent Switch LOW/HIGH
7 Power Battery Voltage OUT OF RANGE/ IN
RANGE
8 Pinch strip- pinch condition(PSD Only) Not Pinched/Pinched
9 Park Switch Out Of Park/Park
10 Ignition Swtich LOW/HIGH
11 Child Lock Status (PSD Only) Lock/Unlock
12 Lock Status (PSD Only) Lock/Unlock
13 Handle Switch (PSD Only) Not Pressed/Pressed
14 Local Open/Close Switch Not Pressed/Pressed
15 Master Open/Close Switch Not Pressed/Pressed
16 Learn Process Complete Status Not
Complete/Complete
17 Vehicle Speed Slow Status ≥5kph / < 5kph
18 On/Off Switch ON/OFF
19 Start Switch LOW/HIGH
20 PSD Right Select Status Left/Right
21 Fuel Filler Door switch LOW/HIGH
22 Door/Gate Open Feedback Voltages
23 Door/Gate Close Feedback Voltages
24 Unlatch Feedback Voltages
25 Clutch Feedback Voltages
26 Door/Gate Position Count -
27 Most Recent Cinch Time ms
28 2nd Most Recent Cinch Time ms
29 3rd Most Recent Cinch Time ms
30 4th Most Recent Cinch Time ms
31 Left Pinch Strip Voltage Voltages
32 Right Pinch Strip Voltage Voltages

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Check the power sliding door control module input/output value by using the diagnostic tool.
2. When checking the latch, select a vehicle type and "POWER SLIDING/TAIL GATE" menu.
3.Select the "POWER SLIDING DOOR".
4.Select the sensor output. And then check the unlatch feedback (Unlocked state) voltage while operating power
sliding door in power mode.
※ Above voltage and numerical value may be different from the real value.
5. If there is no change in voltage, change the latch.
ANTI PINCH STRIP
1.Check the power sliding door control module input/output value by using the diagnostic tool. If the operation of door
control module is abnormal, replace anti pinch strip control module.
2. When checking the anti pinch strip operation, select a vehicle type and "POWER SLIDING/TAIL GATE" menu.

2.When the power ON/OFF button (PWR) (B) is ON, the power sliding door and power tailgate can be opened and
closed automatically by using the switch.
3. When the power tail gate door will power open/close fully, the warning lamp and the chime will operate 3 times.
4. General rules for chime functions
a. Chime & tail lamp shall operate prior to and during power opening or closing the Tailgate : 3 Times (0.5 sec on,
0.5 sec off), after 1 chime start opening or closing with two chimes.
b. Chime shall operate when a power operation cannot be performed as requested except handle pull : 1 Time
(Duration 0.5 second on)
c. Chime shall operate when an obstacle has been detected : 3 Times (0.5 sec on, 0.5 sec off)
d. Chime shall operate if PTG has not reached primary latch position after a power cinch cycle : 3 Times (0.5 sec
on, 0.5 sec off)
POWER TAIL GATE OPERATING CONDITION
1.The tail gate will not power open when vehicle is moving above 3 mph (5 km/h) or the gearshift lever is not in P
(Park) for automatic transaxle.
2. The power tail gate will not open with the transmitter or the main control button when all power sliding doors are
locked and closed.
3. The power tail gate will detect the resistance, then stop movement or move to the full open position to allow the
object to be cleared.
4. If the automatic stop and reversal feature operates continuously more than twice during one opening or closing
operation, the power tail gate may stop at that position. At this time, close the tailgate manually and operate the
tailgate automatically again.
5. The PTG system is an electronic device and requires a minimum battery voltage to operate. The Electronic Control
Unit (ECU) monitors the battery voltage present at the ECU input battery input and will not permit operation if the
battery voltage is out of range.
6. If the PTG button is pressed during closing operation, the power tail gate may reverse direction and open fully.
7. Remove the accumulated snow or ice on the power tail gate before operating.
a.To prevent the battery from being discharged, do not leave the power sliding door and power tailgate at
open position for a long time.
b. The PTGM will go to a sleep mode and power operation will be disabled if the tail gate is left open longer
than 6 hours.
Manually close the tail gate to the latched position to reset the PTGM. Power operation will be restored.
a.Always disconnect the negative battery cable before attempting any power tailgate system service.
b. Never attempt to enter or exit the vehicle with the tailgate in motion. You could be injured or cause
damage to the power tailgate system and or components.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Remove the steering column upper and lower shrouds (A) after removing 3 screws.
2.Remove the wiper switch (A) by pushing the lock pin (B) after disconnecting the connector.
[LHD]
[RHD]
3.Installation is the reverse of removal.
INSPECTION
Check for continuity between the terminals while operating the wiper and washer switch. If it is not normal condition,
replace wiper and wiper switch.
[LHD]

2007 > 2.7L V6 GASOLINE >
REMOVAL
The rain sensor may not operate proprly if contaminated. Protect the rain sensor surface by not removing the
cover until installation time. The coupling pad on the rain sensor surface has adhesive strength. Take care when
installing the sensor. If the sensor is separated from the windshield by force, the sensor or windshield may be
damaged. Take care when removing the sensor.
1. Remove the sensor cover. When removing it, make sure take care to prevent damage. To remove it, press back
the locking hook using the cover hole using an appropriate tool.
2.When removing rain sensor from the bracket, open the spring clip using the ( - )driver, and then remove.
3.Disconnect the wiring harness connector from the sensor.
4. Rain sensor is fitted with 2 spring slides by clip type on the front glass, it can be replaced easily. When replacing
the front glass, take away the rain sensor from the existing glass.
After then attach it to new one again.
INSTALLATION
a.In case of the windshield with reflection layer which reflects the infrared rays in sensing field, remove the
reflection layer from the rain sensor mounting position prior to installation.
b. Bracket and spring slide need for installing the rainsensor, it is covered by sensor cover.
1. Install the rain sensor bracket to the windshield glass using the tape

2.Rain sensor Installation
The two springs should be closed simultaneously. Once closed, press the housing forward to ensure proper
adhesion of the sensor to the windshield.
3.Connect the rain sensor connector, and then install the sensor cover.
It is very important that the coupling pad pushes against the windshield completely to prevent bubbles from
forming at the contact surface.
INSPECTION
1.Wiper blade
Check the wear of wiper blade. If it is excessively worn, wipe out clean to sense the rain amount accurately.
2. Coupler
Ensure the coupler surface on the windshield is free of bubbles. Verify that the coupler is properly positioned.
3. Glass
Check the windshield glass surface beyond the sensing range for the excessive wear, scratch or crack.
Although the sensor compensates for wear to a certain level, sensor fails to sense accurately if it excceds a certain
level. This is confirmed by the self - diagnosis of sensor.
4. Exterior cover
Ensure the exterior cover of the rain sensor is properly installed.
5. Spring clip
Check the spring clip after removal of exterior cover if the rain sensor is disconnected from coupler.
6. Connector
(1) Check the terminal inside the connector and wiring for compression, and check the terminal whether it is
inserted and locked correctly.
(2) In addition, check the wiring connector and rain sensor connector for assembly and confirm to prevent poor
connection

3.After moving the slide 5mm forward, release the switch just momentarily.
a. If the operation above is normal condition, the sunroof opens and closes.
4. When the sunroof is closed completely, turn OFF the UP switch initialize the motor completely.
WHEN TO INITIALIZE THE MOTOR
1.First operation the vehicle after manufactured it.
2. Initial value is erased or damaged because of short power electric discharge during operation
3. After using the manual handle.
OPERATING THE SUNROOF EMERGENCY HANDLE
1.Use the sunroof emergency handle to close and open the sunroof manually for the following case only.
a. To close the sunroof before driving a vehicle in a rainy day or on the highway if the sunroof cannot be closed
due to failure of the sunroof motor or controller.
2. Operating method
a. Remove the overhead console
b. Push the emergency handle up into the hexagonal drive (A) of the sunroof motor. You must push hard enough
to disengage the motor clutch; otherwise the emergency handle will slip due to incomplete fit in the motor.
c. Carefully turn the emergency handle clockwise to close the sunroof.
d. After closing the sunroof, wiggle the handle back and forth as you remove the tool from the motor, to ensure the
motor clutch reengages.
e. A 5mm hex socket may be used in place of the emergency handle, with a” Speeder” type handle.
a.Do not use power tools to operate the sunroof.
b. Damage to the components may occur.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
FRONT TURN SIGNAL LAMP
1. Disconnect the negative ( - ) battery terminal.
2. Remove front lamp assembly.
3. Remove the socket in a counterclockwise direction.
4.Replace the bulb (A).
REAR TURN SIGNAL LAMP
1.Disconnect the negative ( - ) battery terminal.
2. Remove the rear lamp assembly (A) after removing the mounting screw (3EA) and connector.
3.Remove the socket in a counterclockwise direction and replace the bulbs.
SIDE TURN SIGNAL LAMP
1.Disconnect the negative ( - ) battery terminal.
2. Disconnect the connector after removing the lens.

3.Remove the socket in a counterclockwise direction.
4.Replace the bulb.