sliding door KIA CARNIVAL 2007 Owner's Guide

2007 > 2.7L V6 GASOLINE >
INSPECTION
SLIDING DOOR MOTOR INSPECTION
1. It will be able to diagnose defects of PSD motor with scan tool quickly.
2. Select model and menu(BCM).
3.Select "rear area module(RAM)".
4.Select the "Actuation test" and "PSD open/close" to operate tailgate motor.
5.Replace the drive unit, if actuator operates abnormal.
DRIVE UNIT CLUTCH INSPECTION
1.Check the power sliding door control module input/output value by using the diagnostic tool. If the operation of
power sliding control module is abnormal, replace power sliding door drive unit.
2. When checking the clutch operation, select a vehicle type and "POWER SLIDING/TAILGATE" menu.

3.Select the "POWER SLIDING DOOR" to check.
4.Select the sensor output. And then check the clutch feedback sensor output while operating power sliding door in
power mode.
※ Above voltage and numerical value may be different from the real value.
5. Change the drive unit, if there is no change during operation.
OPTICAL SENSOR INSPECTION
1.Check the power sliding door control module input/output value by using the diagnostic tool.
2. When checking the optical sensor, select a vehicle type and "Power sliding/tailgate" menu.

3.Select the "POWER SLIDING DOOR" to check.
4.Select the sensor output. And then check the optical sensor volt while operating power sliding door in power mode.
※ Above voltage and numerical value may be different from the real value.
5. Change the drive unit, if there is no change during operation.
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the rear trim panel (Refer to the Body group - interior trim)
3. Disconnect the connectors (6EA) from the power sliding door drive unit.
4. Remove the rear combination lamp (Refer to the Body group - rear bumper)
5. Remove the mounting bolts (4EA) and rail cover (A).

TORQUE : 7 - 11 N.m (0.7 - 1.1 Kg.m)
10.Loosen the mounting bolt (1EA) and nuts (2EA). And then remove the power sliding door drive unit assembly after
removing the front cable.
TORQUE : 7 - 11 N.m (0.7 - 1.1 Kg.m)
11. Installation is the reverse of removal.
12. When installation, check the grease on the center roller hinge barrel and club contact part (A).
a.A learn cycle must be performed whenever the power is removed.
b. Check the normal operation whenever a power sliding door component is removed or replaced. If the
chime sound is heard, check the DTC, wiring harness and cable connections.

Power Sliding Door Control Module

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal..
2. Remove the rear trim panel (Refer to the Body group - interior trim)
3. Remove the connectors and mounting bolts (2EA) from the power sliding door unit(A). And then remove the power
sliding door control module (B).
TORQUE 0.25 - 0.35N.m(0.025- 0.035Kg.m)
4.Installation is the reverse of removal.
a.A learn cycle must be performed whenever the power is removed.
b. Check the normal operation whenever a power sliding door component is removed or replaced. If the
chime sound is heard, check the DTC, wiring harness and cable connections.

Power Sliding Door Buzzer

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Remove the rear side trim (Refer to the Body group - interior trim).
2. Disconnect the sliding door chime connector (A) from chime (B).
3.Remove the chime from drive unit and replace it with a new one.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Detent switch detect the latch position within latch assembly.
2.Check the power sliding door control module input/output value by using the diagnostic tool.
3. When checking the detent switch, select a vehicle type and "POWER SLIDING/TAIL GATE" menu.
4.Select the "POWER SLIDING DOOR".
5.Select the detent sensor output. And then check the detent switch output with operating power sliding door.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Check the power sliding door control module input/output value by using the diagnostic tool.
2. When checking the latch, select a vehicle type and "POWER SLIDING/TAIL GATE" menu.
3.Select the "POWER SLIDING DOOR".
4.Select the sensor output. And then check the unlatch feedback (Unlocked state) voltage while operating power
sliding door in power mode.
※ Above voltage and numerical value may be different from the real value.
5. If there is no change in voltage, change the latch.
ANTI PINCH STRIP
1.Check the power sliding door control module input/output value by using the diagnostic tool. If the operation of door
control module is abnormal, replace anti pinch strip control module.
2. When checking the anti pinch strip operation, select a vehicle type and "POWER SLIDING/TAIL GATE" menu.