lock KIA Optima 2006 2.G User Guide

3-11
REAR DOOR CHILD
SAFETY LOCKThe child safety lock is provided to help
prevent children from accidentally
opening the rear doors from inside the
vehicle.
• To lock a rear door so that it cannot
be opened from the inside, push the
child safety lock located on the rear
edge of the door to the “LOCKED”
position before closing the door.
• To open a rear door while the child
safety lock is engaged, push the door
lock button to the “UNLOCK”
position (red mark is visible) then
pull the outside door handle.
WINDOWSPOWER WINDOWS The ignition switch must be in the ON
position for power windows to operate.
Each door has a power window switch
that controls the door’s window.
However, the driver has a power window
lock switch which can cancel the
operation of the three passenger window
switches.✻
NOTICE
To prevent the power window fuse
from malfunctioning and the power
window system from being
damaged, do not open or close
more than two windows at the
same time.
WARNING - Rear Door
Locks
If children accidentally open the
rear doors while the vehicle is
in motion, they could fall out
and be seriously or fatally
injured. To prevent children
from opening the rear doors
from the inside, the rear door
safety locks should be used
whenever children are in the
vehicle.
MMSA3005
LOCKFREE
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 11

DRIVER’S DOOR POWER
WINDOW CONTROLSAll windows can be opened or closed
using the power window master control
on the driver’s door. To open a window,
press down on the corresponding power
window switch. To close a window, pull
up on the corresponding power window
switch.
DRIVER’S WINDOW
AUTOMATIC-DOWN WINDOW
SWITCHThe driver’s window has an “Automatic-
Down” feature. To activate the express-
down feature, momentarily depress the
front of the switch to the second detent
position. To cancel this feature, pull up
on the front of the switch and then
release it.DRIVER’S POWER WINDOW
SWITCHThe driver’s power window switch
provides two (2) separate window-down
functions.
• Depressing the driver’s power
window switch completely, automa-
tically lowers (Automatic-Down) the
driver’s window. To cancel this
function, pull up on the front of the
switch and release it.• Depressing the driver’s power
window switch partially (to the first
detent) provides precise control of the
window-down position.
To raise/close the driver’s window,
pull up on the power window switch.
POWER WINDOW TIMER
(IF EQUIPPED)The power windows can be operated for
approximately 30 seconds after the
ignition key is removed or turn to the
ACC or LOCK position. However, if the
front doors are opened, the power
windows cannot be operated even within
the 30 seconds after the ignition key
removal.
KNOWING YOUR VEHICLE
3-12
MMSA3004
Power window master controlPower window lock switch
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 12

POWER WINDOW LOCK
SWITCH FEATUREThe driver can disable the power window
switches on all passenger doors by
depressing the power window lock switch
located on the driver’s door to ON. When
the power window lock switch is ON, the
driver’s master control can not operate the
passenger door power windows either.
PASSENGER DOOR POWER
WINDOW CONTROLSTo open a window, press the front portion
of the switch down. To close a window,
pull the front portion of the switch up.
3-13
MMSA3006
WARNING - Power
Windows
 Keep the power window lock
switch on the driver’s door in
the ON (depressed) position
except when someone is
operating a passenger door
window. Serious injury can
result from unintentional
window opera-tion, especially
to children.
 Always double check to make
sure all arms, hands, and other
obstructions are safely out of
the way before closing a
window.✻
NOTICE
If you experience buffeting and
pulsation (wind shock) with either
side window open, you should open
the opposite window slightly to
reduce the condition.
WARNING - Passengers
Do not allow children to play
with the power windows. They
may seriously injure
themselves or others.
MMSA3004
Power window lock switch
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 13

SEATS
FRONT SEAT ADJUSTMENTMOVING THE FRONT SEAT
FORWARD AND BACKWARDTo move the seat forward or backward;
1. Pull the seat slide adjustment lever
under the front edge of the seat
cushion up and hold it.
2. Slide the seat to the position you
desire.
3. Release the lever and make sure the
seat is locked in place.
KNOWING YOUR VEHICLE
3-14
MMSA3007
WARNING - Drivers
 Never adjust the driver’s seat
or seatback when the vehicle
is moving. Doing so could
cause loss of control, and
serious personal injury or
death.
 Do not allow packages or
other objects to interfere with
the normal position of a
seatback. These objects may
prevent the seatback from
locking, which could result in
serious injury or death in the
event of a sudden stop or
collision.
 Always drive and ride with
your seatback upright and
the lap portion of the safety
belt snug and low across the
hips.
 Children can be killed or
injured by the passenger air
bag. The back seat is the
safest place for children 12
and under. Make sure all
children use seat belts or
child seats.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 14

ADJUSTING THE FRONT
SEATBACK RECLINERTo recline the seatback;
1. Lean forward slightly and lift up on
the seatback recline lever located on
the outside of the seat, toward the rear.
2. Lean back on the seat and adjust the
back of the seat to the position you
desire.
3. Release the lever and make sure the
seatback is locked in place. (The
lever MUST return to its orginal
position for the seatback to lock.)
3-15
MMSA3008
CAUTION
Do not place anything under the
front seats. Loose objects might
interfere with the seat slide
mechanism or possibly roll out
from under the seat and interfere
with the operation of the brake,
clutch or accelerator foot pedals.
WARNING - Passengers
To reduce the risk of sliding
under the lap portion of the
lap/shoulder belt, and potentially
suffering serious personal injury
or death in the event of a
collision, do not use the front
seatback in a reclined position
while the vehicle is in motion. If a
seat is reclined, the occupant’s
hip could slide under or out of
the lap portion of the
lap/shoulder belt during a
collision. If that occurs, the
occupant may no longer be
properly restrained, and the
safety belt could apply restraint
forces to the unprotected
abdomen resulting in serious
personal injury or death.
Therefore, keep the seatbacks in
a comfortably upright position
whenever the vehicle is in
motion.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 15

ADJUSTING SEAT FORWARD
AND BACKWARDPull the control knob forward or
backward to move the seat forward or
backward to the desired position.
Release the knob and then the seat will
lock at that position.
1. Reclining Control Knob
2. Sliding and Height Adjusting Control
Knob
3-17
MMSA3011
WARNING
 Never attempt to adjust the
seat while the vehicle is
moving. This could result in
loss of control, and an
accident causing death,
serious injury, or property
damage.
 Do not sit or lean
unnecessarily close to the
airbag to get better
protection during its deploy-
ment in case of an accidents.
 Sit at least 10 inches (250
mm) away form the steering
wheel while driving the
vehicle to avoid injury during
air bag deployment in an
accident.
WARNING
To ensure the seat is locked
securely, attempt to move the
seat forward or backward
without using the control knob.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 17

KNOWING YOUR VEHICLE
3-18SEAT CUSHION HEIGHT
ADJUSTMENTMove the front portion of the control
knob up or down to raise or lower the
front part of the seat cushion. Move the
rear portion of the control knob up or
down to raise or lower the rear part of the
seat cushion.
ADJUSTING SEATBACK
ANGLERotate the upper portion of the control
knob forward or backward to recline the
seatback to the desired position. Release
the control knob and then the seatback
will lock in that position.
MMSA3078/MMSA3015
MMSA3012
WARNING
To minimize the risk of personal
injury in the event of a collision
or a sudden stop, both the
driver's and passenger's
seatback should remain in an
upright position while the car is
in motion. The protection
provided by the seat belts and
airbags may be reduced signifi-
cantly when the seatbacks are
reclined. There is a greater risk
that the seat occupants will
slide under the belt resulting in
serious injury if a crash occurs
when the seat-backs are
reclined. The seat belt cannot
provide full protection to an
occupant if the seat back is
reclined.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 18

KNOWING YOUR VEHICLE
3-20
SPLIT FOLDING REAR
SEATThe rear seatbacks fold forward to
provide additional cargo space and to
provide a access to the trunk area.
• To fold the rear seatback(s) down,
press the unlock button located in the
top of the seatbacks, then fold the
seatback forward and down.
• To raise the seatback, lift and push it
firmly until it clicks into place.
• When you return the seatback to its
upright position, reposition the rear
safety belts so that they can be used
by rear seat passengers.
MMSA3014
WARNING
To drive properly, adjust the
driver’s seat and its headrest
before starting. After doing so,
you should adjust the day/night
rearview mirror and the outside
rearview mirror.
WARNING - Cargo
Cargo should always be
secured to prevent it from
shifting and causing injury to
the vehicle occupants.
CAUTION
Do not remove the floor carpet in
your vehicle, emission controls
cause high exhaust temperatures
under the floor.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 20

3-21
REAR SEATBACK LOCKThe rear seatback lock lever (located on
the backside of the rear seatback) is
always in the “LOCK” position when the
seatbacks are secured upright. To fold the
rear seatback down, the lock lever must be
moved to the “FREE” position. The lock
feature was designed to provide protection
from unauthorized entry into the trunk.
REAR SEAT ARMRESTThis armrest is located in the center of
the rear seatback.
Open the armrest cover by pressing its
release button. A cup holder and stowage
compartment are inside the armrest.
FREE LOCK
MMSA3018
MMSA3019
✻
NOTICE
When returning the rear seatbacks
to the upright position, remember
to return the rear shoulder belts to
their proper position. Routing the
safety belt webbing through the
rear safety belt guides will help
keep the belts from being trapped
behind or under the seats.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 21

KNOWING YOUR VEHICLE
3-22SAFETY BELTSPRE-TENSIONER SEAT
BELTYour vehicle is equipped with driver’s
and front passenger’s pre-tensioner seat
belts. The purpose of the pre-tensioner is
to make sure that the seat belts fit tightly
against the occupant’s body in certain
frontal collisions.The pre-tensioner seat belts can be
activated alone or, with the airbag, where
the frontal collision is severe enough.
The pre-tensioner seat belt operates in
the same way as an Emergency Locking
Retractor (ELR) type of seat belt. When
the vehicle stops suddenly, or if the
occupant tries to lean forward too
quickly, the seat belt retractor will lock
into position. However, in certain frontal
collisions, the pretensioner will activate
and pull the seat belt into tighter contact
against the occupant’s body.The seat belt pre-tensioner system
consists mainly of the following
components.
Their locations are shown in the
illustration.
1. SRS airbag warning light.
2. Seatbelt pre-tensioner assembly.
3. SRS control module.
2GHB3002
MMSA3021
Driver’s side airbag
21
3Passenger’s
side airbag
WARNING
To obtain maximum benefit
from a pre-tensioner seat belt:
1. The seat belt must be worn
correctly.
2. The seat belt must be
adjusted to the correct
position.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 22