brake KIA Optima 2006 2.G Owner's Manual

1-3
VEHICLE BREAK-IN
PROCESSNo special break-in period is needed.
By following a few simple precautions
for the first 1,000 km (600 miles) you
may add to the performance, economy
and life of your vehicle.
 Do not race the engine.
 Do not maintain a single speed for
long periods of time, either fast or
slow. Varying engine speeds are
beneficial for proper engine break-in.
 Avoid hard stops, except in
emergencies, to allow the brakes to
seat properly.
 Avoid full-throttle starts.
MS-CNA-Eng 1.QXD 7/25/2005 5:14 PM Page 3

YOUR VEHICLE AT A GLANCE
2-2INTERIOR AND EXTERIOR OVERVIEW1. Rearview mirror
2. Sunvisor
3. Sunroof (If Equipped)
4. Seat
5. Spare tire6. Tail-lights
7. Fuel filler lid
8. Parking brake
9. Rear door child safety lock
10. Power window switches 11. Door
12. Outside rearview mirror
13. Air bags
4
5
6
7 8 9 101112
13123
MMSA2001
MS-CNA-Eng 2.QXD 7/25/2005 5:18 PM Page 2

2-3
INSTRUMENT PANEL OVERVIEW1. Instrument cluster
2. Air bag
3. Climate control
4. Clock
5. Radio (If Equipped)6. Air bag
7. Vent
8. Glove box
9. Shift lever (Automatic)
10. Parking brake11. Wiper/Washer
12. Power outlet
13. Hood release
14. Light control/Turn signals
15. Steering wheel
R
E
S
AC
C
E
L
CA
N
C
E
LC
O
A
S
TS
E
T
4
5
67
8 9
10 1112
13 7
151
1423
MMSA2002
MS-CNA-Eng 2.QXD 7/25/2005 5:18 PM Page 3

DOOR LOCKS MANUAL DOOR LOCKSOPERATING DOOR LOCKS -
WITH KEY• Both front doors can be locked and
unlocked with the key.
• Turn the key to the left to lock and to
the right to unlock the door.
• Once a door is unlocked, it may be
opened by pulling the door handle.
OPERATING DOOR LOCKS-
WITHOUT KEYTo lock a door without the key, push the
inside door lock button to the “LOCK”
position and close the door.
3-9
MMSA3001
MMSA3002 LOCK UNLOCK
✻
NOTICE
Always remove the ignition key,
engage the parking brake, close all
windows and lock all doors when
leaving your vehicle unattended.
CAUTION
The transponder in your ignition
key is an important part of the
immobilizer system. It is designed
to give years of trouble free service,
however you should avoid exposure
to moisture, static electricity and
rough handling. Immobilizer
system malfunction could occur.
CAUTION
Do not change, alter or adjust the
immobilizer system because it
could cause the immobilizer system
to malfunction and should only be
serviced by an authorized Kia
dealer.
Malfunctions caused by improper
alterations, adjustments or
modifications to the immobilizer
system are not covered by your
vehicle manufacturer warranty.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 9

ADJUSTING THE FRONT
SEATBACK RECLINERTo recline the seatback;
1. Lean forward slightly and lift up on
the seatback recline lever located on
the outside of the seat, toward the rear.
2. Lean back on the seat and adjust the
back of the seat to the position you
desire.
3. Release the lever and make sure the
seatback is locked in place. (The
lever MUST return to its orginal
position for the seatback to lock.)
3-15
MMSA3008
CAUTION
Do not place anything under the
front seats. Loose objects might
interfere with the seat slide
mechanism or possibly roll out
from under the seat and interfere
with the operation of the brake,
clutch or accelerator foot pedals.
WARNING - Passengers
To reduce the risk of sliding
under the lap portion of the
lap/shoulder belt, and potentially
suffering serious personal injury
or death in the event of a
collision, do not use the front
seatback in a reclined position
while the vehicle is in motion. If a
seat is reclined, the occupant’s
hip could slide under or out of
the lap portion of the
lap/shoulder belt during a
collision. If that occurs, the
occupant may no longer be
properly restrained, and the
safety belt could apply restraint
forces to the unprotected
abdomen resulting in serious
personal injury or death.
Therefore, keep the seatbacks in
a comfortably upright position
whenever the vehicle is in
motion.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 15

4-1
DRIVING YOUR VEHICLEIgnition Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Manual Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6
Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12
Power Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-18
Tilt Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-18
Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-19
Gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-20
Warnings and Indicators . . . . . . . . . . . . . . . . . . . . . . . .4-21
Lightings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27
Wipers and Washers . . . . . . . . . . . . . . . . . . . . . . . . . . .4-30
Rear Window Defroster . . . . . . . . . . . . . . . . . . . . . . . . .4-32
Interior Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-33
Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-37
Traction Control System . . . . . . . . . . . . . . . . . . . . . . . .4-40
Climate Control System . . . . . . . . . . . . . . . . . . . . . . . .4-42
Automatic Heating and Cooling Control System . . . .4-47
Windshield Defrosting and Defogging
(Manual Type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-54
Windshield Defrosting and Defogging
(Automatic type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-56
4
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 1

IGNITION SWITCH ILLUMINATED IGNITION
SWITCHWhenever a door is opened, the ignition
switch will be illuminated for your
convenience, provided the ignition
switch is not in the “ON” position. The
light will go off approximately 10
seconds after closing the door or when
the ignition switch is turned on.
IGNITION SWITCH AND
ANTITHEFT STEERING
COLUMN LOCK IGNITION SWITCH POSITIONLOCKThe steering wheel is locked to protect
against theft. The ignition key can be
removed only in the LOCK position. For
vehicles equipped with an automatic
transaxle, it also locks the gear shift lever
in the P (Park) position.
ACC (ACCESSORY)Turning the ignition switch to this
position unlocks the steering wheel and
will allow some of your vehicle’s
electrical accessories such as the radio to
operate when the engine is OFF.ONTurning the ignition switch to this
position allows you to test your vehicle’s
warning lights (except the brake system
warning light) to make sure they work
before you start the engine. The ignition
key returns to the ON position once the
engine is started and remains in this
position while the engine is running.
Do not leave the ignition switch in the
ON position for extended periods with
the engine OFF because the battery will
discharge.
DRIVING YOUR VEHICLE
4-2
PUSH
LOCKACCONSTSRT
MMSA4058
PUSH
MMSA4001
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 2

STARTTurn the ignition key to the START
position to start the engine. The engine
will crank until you release the key, then
it returns to the ON position. Also, the
brake warning indicator illuminates to
check the bulb in this position.
Difficulty in turning the ignition key to
the START position can be caused by
pressure on the switch from the steering
column. To allow the ignition key to turn,
move the steering wheel right or left to
release the tension and then turn the key.
AUTOMATIC TRANSAXLEWhen turning the ignition switch to the
LOCK position, the shift lever must be
in the P (Park) position.MANUAL TRANSAXLEWhen turning the ignition switch to the
LOCK position, push the key inward at
the ACC position and turn the key
toward the LOCK position.
4-3
✻
NOTICE
For safety, the engine will not start
if the clutch pedal is not depressed
fully on manual transaxle equipped
models.
WARNING
• Never turn the ignition switch
to LOCK or ACC while the
vehicle is moving. This could
result in loss of directional
control and braking function,
which could cause an
immediate accident.
 Never reach for the ignition
switch, or any other controls,
through the steering wheel
while the vehicle is in motion.
Failure to observe this
warning can result in loss of
vehicle steering and braking
control, which may result in
an accident.
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 3

STARTING THE ENGINE1. Make sure the parking brake is applied.
2.Manual Transaxle- Depress the
clutch pedal fully and shift the
transaxle into NEUTRAL. Keep the
clutch pedal depressed while
cranking the engine.
(For safety, the engine will not start if
the clutch pedal is not depressed fully
on manual transaxle equipped
models.)
Automatic Transaxle- Place the
transaxle shift lever in P (Park).
Depress the brake pedal fully.
You can also start the engine if the
shift lever is in the N (Neutral)
position.
3. Turn the ignition switch to START
and hold it until the engine starts (a
maximum of 10 seconds), then
release the key.In extremely cold weather, below 0ºF
(minus 18ºC), or after the vehicle has not
been operated for several days, let it
warm up without depressing the
accelerator.
Whether the engine is cold or warm, it
should be started without depressing the
accelerator.If the engine fails to start using this
procedure, attempt the following.
The engine fails to start when the engine
is cold (engine coolant temperature is
below 32ºF/0ºC):
A no start condition may be caused by an
engine that has become flooded (has
excessive fuel in the cylinders). If this is
the case, follow the starting procedure
below.
1. Make sure the parking brake is applied.
2.Manual Transaxle- Depress the
clutch pedal fully and shift the
transaxle into N (Neutral). Keep the
clutch pedal depressed while
cranking the engine.
Automatic Transaxle- Place the
transaxle shift lever in P (Park) or N
(Neutral). Depress the brake pedal
fully.
3. Depress the accelerator fully and
hold it.
DRIVING YOUR VEHICLE
4-4
CAUTION
If the engine stalls while you are in
motion, do not attempt to move the
shift lever to P (Park).
If it is safe to do so considering traf-
fic and road conditions, you may
put the shift lever in the N
(Neutral) position while still mov-
ing and turn the ignition switch to
the START position in an attempt
to restart the engine.
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 4

4. While holding the accelerator fully
depressed, turn the ignition switch to
the START position and hold it (a
maximum of 10 seconds) to discharge
the excess fuel.
If the engine starts, the engine speed
will increase suddenly; immediately
release the ignition key and the
accelerator.
If the engine has not yet started,
release the accelerator after cranking
the engine.
5. Without depressing the accelerator,
crank the engine until it starts (a max-
imum of 10 seconds).
If the engine fails to start when the
engine is warm:If the engine is unusually difficult to
restart when it is warm (fails to start
after repeated attempts without
depressing the accelerator):
1. Make sure the parking brake is
applied.
2.Manual Transaxle- Depress the
clutch pedal fully and shift the
transaxle into N (Neutral). Keep the
clutch pedal depressed while
cranking the engine.
Automatic Transaxle- Place the
transaxle shift lever in P (Park) or N
(Neutral). Depress the brake pedal fully.
3. While depressing the accelerator
pedal about halfway down, turn the
ignition switch to the START
position and hold it (a maximum of
10 seconds).
4. After the engine has started, let it idle
for about 10 seconds before driving.In some models, the starter may not
operate if:
• In an automatic transaxle, the shift lever
is NOT in P (Park) or N (Neutral).
• In a manual transaxle, the clutch
pedal is not fully depressed.
Excessive engine noise (from valve
tappets) may occur if the engine has not
been operated for an extended period.
The noise should stop after the engine has
reached normal operating temperature.
If the noise does not stop, have the vehicle
inspected by an Authorized Kia Dealer.
4-5
✻
NOTICE
Do not engage the starter for more
than 10 seconds. If the engine stalls
or fails to start, wait 5 to 10 seconds
before re-engaging the starter.
Excessive or improper use of the
starter may damage it.
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 5