change wheel Lancia Delta 2011 Owner handbook (in English)

IN AN EMERGENCY195
4
REMOVING THE SUBWOOFER
(versions with Bose HI-FI)
(for versions/markets, where provided)
IMPORTANT The following procedure only applies to
cars equipped with Bose HI-FI systems with subwoofer
(for versions/markets, where provided).
SUBWOOFER AND SPACE-SAVER WHEEL
Proceed as follows to remove the Subwoofer:
❍open the luggage compartment, pull tab A-fig. 10 and
lift up the mat;
❍undo locking device A-fig. 8 and lift up the Sub-
woofer. Then remove connection cable B from velcro
attachment C;❍rest the Subwoofer to one side in the luggage com-
partment, remove the container and take out the
space-saver wheel;
❍change the wheel as described in this chapter.
After tyre replacement:
❍reposition the container and place the Subwoofer on
top of it, taking care to position it according to the in-
structions on the container (fig. 9) so that the arrow
on the spacer is pointing in the direction of travel;
❍rest cable B-fig. 8 on velcro attachment C to avoid
pinching it. Then tighten locking device A-fig. 8.
Lower the luggage compartment mat.
fig. 8L0E0176mfig. 9L0E0177m

196IN AN EMERGENCY
TAKING OUT THE SPACE-SAVER WHEEL
Please note that:
❍the jack weight is 1.76 kg;
❍the jack requires no adjustment;
❍the jack cannot be repaired; if it breaks, it must be re-
placed with a new one of the same type;
❍no tool other than its cranking device may be fitted on
the jack.
To change a wheel proceed as follows:
❍stop the car where it is not a danger to other road
users and you can replace the wheel safely. The
ground must be flat and sufficiently compact;
❍turn the engine off and engage the handbrake;
❍engage first gear or reverse;
❍lift up the luggage compartment mat using handle A-
fig. 10 (in the presence of a double load platform, first
lift the upper cover and then the luggage compart-
ment mat);
❍unscrew the locking device B-fig. 10;
❍take out the tool box C and place it next to the wheel
to be changed;
❍remove the space saver wheel D-fig. 10;
❍use the provided screwdriver to remove the hub cap,
levering the dedicated opening on the outer edge;
fig. 10L0E0081m

IN AN EMERGENCY197
4
❍in the presence of a double load compartment, lift the
double compartment mat and attach it to the luggage
compartment mat as shown in fig. 10;
❍for cars fitted with alloy wheels, remove the press-fit-
ted hub cap using the screwdriver provided;
❍loosen the fixing bolts for the wheel to be changed by
about one turn using the spanner provided E-fig. 11;
❍turn the jack handle to partially open it;
❍position the jack near the wheel to be replaced at the
reference point
Oon the side member;
❍make sure that the splines F-fig. 12 on the jack are
firmly fitted to tab G on the side member;
fig. 11L0E0082mfig. 12L0E0083m

200IN AN EMERGENCY
After tyre replacement
❍Stow the space saver wheel D-fig. 10 in the space pro-
vided in the luggage compartment;
❍fit the partially open jack in its box forcing it lightly
to prevent it from vibrating when travelling;
❍put the tools back into place in the container;
❍stow the container, complete with tools, in the spare
wheel and tighten the locking device B-fig. 10;
❍reposition the boot mat correctly.
IMPORTANT Do not use inner tubes with tubeless tyres.
Check the inflation pressure of the tyres and the space-
saving wheel periodically.CHANGING A BULB
GENERAL INSTRUCTIONS
❍Before changing a bulb, check the contacts for rust-
ing;
❍burnt-out bulbs must be replaced by others of the
same type and wattage;
❍always check the alignment of the beam after chang-
ing a headlight bulb;
❍when a light is not working, check that the corre-
sponding fuse is intact before changing a bulb. For the
location of fuses, refer to the paragraph “Replacing
fuses” in this chapter.
Modifications or repairs to the electric sys-
tem that are not carried out properly or do
not take the system technical specifications
into account can cause malfunctions leading to the
risk of fire.
Various fastening bolts and space-saver
wheels, specific and differing in structural
characteristics, are used depending on the
wheel rim type (alloy or steel). Fastening bolts for
alloy rims can be identified by the presence of a per-
manent washer and a hollow side on the bolt head.
Therefore, you will need to go to a Lancia Dealer-
ship to get the correct type of fastening bolts and
space saver wheel if you change the type of wheels
fitted (alloy rims instead of steel rims, or vice
versa). Keep the bolts fitted as standard in case of
re-use of the wheels originally mounted on the car.

242SERVICING AND MAINTENANCE
WHEELS AND TYRES
Check the pressure of each tyre, including the space-saver
wheel, approximately every two weeks and before long
journeys: the pressure should be checked with the tyre
rested and cold.
It is normal for the pressure to increase as the car is used;
see the “Wheels” paragraph in chapter “6” for the cor-
rect tyre inflation pressure.
Incorrect pressure causes abnormal tyre wear fig. 5:
A normal pressure: tread evenly worn.
B low pressure: tread particularly worn at the edges.
C high pressure: tread particularly worn in the centre.
The tyres must be replaced when the tread is less than
1.6 mm thick. In all cases, follow the laws in force in
the country where you are driving.
fig. 5L0E0096m
IMPORTANT NOTES
❍Where possible, avoid braking suddenly, wheel-spin-
ning and crashing into curbs, potholes or other ob-
stacles. Driving for long stretches over bumpy roads
can damage the tyres;
❍check the tyres regularly for cuts on the sides, swelling
or irregular tread wear. Go to a Lancia Dealership
if required.
❍avoid overloading the car when travelling: this may
cause serious damage to the wheels and tyres;
❍if a tyre is punctured, stop immediately and change
it to avoid damage to the tyre, wheel rim, suspension
and steering system;
❍the tyre ages even if rarely used. Cracks in the tread
and on the sidewalls are a sign of ageing. Have the
tyres checked by skilled personnel if they have been
fitted for longer than six years. Remember to check
the space-saver wheel very carefully;

SERVICING AND MAINTENANCE243
5
❍when replacing the tyres, always fit new tyres, avoid-
ing those of dubious origin;
❍If a tyre is replaced, you should also change the in-
flation valve;
❍to allow even wear between the front and rear tyres,
it is advisable to switch them every 10-15 thousand
kilometres, keeping them on the same side of the car
so as not to reverse the direction of rotation.
Remember that the road holding qualities of
your car also depend on the correct inflation
pressure of the tyres.
If the pressure is too low the tyre will get
overheated, with the risk of serious damage
to the tyre.
Avoid moving the tyres from the right side
of the vehicle to the left side and vice versa.
Do not repaint alloy wheel rims at temper-
atures higher than 150 °C. The mechanical
specifications of the wheels might be ad-
versely affected.