window Lancia Delta 2011 Owner handbook (in English)

SERVICING AND MAINTENANCE227
5
35 70 105 140 175
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●● ● ● ●
●●
●● ● ● ●
●●
Diesel versions
Thousands of km
Check tyre condition/wear and adjust pressure if required
Check operation of lighting system
(headlights, direction indicators, hazard warning lights, luggage compartment,
passenger compartment, instrument panel warning lights, etc.)
Check windscreen wiper/washer operation
Check the position/wear of the windscreen/rear window wiper blades
Check condition and wear of front disc brake pads and operation
of pad wear indicator
Check rear disc brake pad liner condition and wear
Condition visual check: bodywork exterior, underbody protection,
pipes and hoses (exhaust – fuel supply system – braking system),
rubber elements (boots – sleeves – bushes – etc...)
Check cleanliness of bonnet and boot locks,
as well as cleanliness and lubrication of linkages
Check and top up, if required, fluid levels
(engine coolant, brake/hydraulic clutch fluid, windscreen washer fluid, battery fluid, etc)
Check handbrake lever travel and adjust if necessary
Check tension and conditions of various accessory drive belts
(except for engines with automatic tensioners)
Check exhaust fumes/emissions
Visually inspect the condition of accessory drive belts

SERVICING AND MAINTENANCE229
5
REGULAR CHECKS
Every 1,000 km or before long journeys, check and, if
necessary, top-up the following:
❍engine coolant fluid level;
❍brake fluid level;
❍windscreen washer fluid level;
❍tyre pressure and condition;
❍operation of lighting system (headlights, direction in-
dicators, hazard lights, etc.);
❍operation of the windscreen wiper/washer system, po-
sition and wear of windscreen/rear window wiper
blades.
Every 3,000 km check and top up if required: engine oil
level.
You are advised to use PETRONAS LUBRICANTS prod-
ucts, which have been designed and produced specifically
for Lancia cars (see table “Capacities” in chapter “6”).
HEAVY-DUTY USE OF THE CAR
Should the prevailing use of the car be under one of the
following specially demanding conditions:
❍trailer or caravan towing;
❍dusty roads;
❍short (less than 7-8 km) and repeated journeys in sub-
zero temperatures;
❍frequently idling engine or long-distance, low-speed
driving (e.g. door-to-door deliveries), or in the event
of long-term inactivity;
❍urban routes;

SERVICING AND MAINTENANCE237
5
WINDSCREEN/REAR WINDOW WASHER FLUID
C-fig. 1-2-3-4
Remove the cap, using the special tab, to add fluid.
Use a mixture of water and TUTELA PROFESSIONAL
SC 35, in the following concentrations:
❍30% TUTELA PROFESSIONAL SC 35 and 70% wa-
ter in summer.
❍50% TUTELA PROFESSIONAL SC 35 and 50% wa-
ter in winter.
At temperatures below −20 °C, use undiluted TUTELA
PROFESSIONAL SC 35 fluid.
Check level through the reservoir.
Close the cap by pressing the centre section.
Do not travel if the windscreen washer
reservoir is empty: using the windscreen
washer is essential for improving visibility.
Some commercial windscreen washer additives
are flammable. The engine compartment contains
hot parts which could start a fire if they come into
contact.
BRAKE FLUID D-fig. 1-2-3-4
Undo the cap and check that the liquid contained in the
reservoir is at the maximum level. The fluid level in the
reservoir must not exceed the MAX mark. If you need to
top up, you should use the brake fluid shown in the “Flu-
ids and lubricants” table (see chapter “6”).
NOTE Carefully clean the cap of the reservoir and the
surrounding surface.
Take great care to ensure that impurities do not enter the
reservoir when the cap is opened.
For topping-up, always use a funnel with integrated fil-
ter with mesh equal to or lower than 0.12 mm.
IMPORTANT Brake fluid is hygroscopic (i.e. it absorbs
moisture). For this reason, if the car is mainly used in ar-
eas with a high degree of atmospheric humidity, the fluid
should be replaced at more frequent intervals than spec-
ified in the “Scheduled Servicing Programme”.

244SERVICING AND MAINTENANCE
RUBBER HOSES
As far as the brake system and fuel rubber hoses are con-
cerned, follow the “Scheduled Servicing Programme” in
this chapter carefully.
Ozone, high temperatures and prolonged lack of fluid in
the system may cause hardening and cracking of the
hoses, with possible leaks. Careful checking is therefore
necessary.
WINDSCREEN/REAR WINDOW
WIPER
BLADES
Periodically clean the rubber part using special products;
TUTELA PROFESSIONAL SC 35 is recommended.
Replace the blades if the rubber edge is deformed or worn.
In any case, it is advisable to replace them approximately
once a year.
A few simple precautions can reduce the possibility of
damage to the blades:
❍make sure that the rubber part is not frozen to the
windscreen in sub-zero temperatures. Use an an-
tifreeze product to release it if required;
❍remove any snow from the glass: in addition to pro-
tecting the blades, this prevents effort from the motor
and overheating;
❍do not operate the windscreen and the rear screen
wipers on dry glass.
Driving with worn wiper blades is a seri-
ous hazard, because visibility is reduced
in bad weather.

SERVICING AND MAINTENANCE245
5
Changing the windscreen wiper blades fig. 6
Proceed as follows:
❍lift the windscreen wiper arm and position the blade
so that it forms an angle of 90° with the arm;
❍press tab A and remove the blade from the arm;
❍insert the new blade making sure it is locked into
place.
fig. 6L0E0097m
Changing the rear window wiper blade fig. 7
Proceed as follows:
❍raise the cover A and remove the arm from the car,
slackening the nut B that fastens it to the pivot pin;
❍fit the new arm, positioning it correctly, and fully
tighten the nut;
❍lower the cover.
fig. 7L0E0098m

246SERVICING AND MAINTENANCE
SPRAY NOZZLES
Windscreen washer fig. 8
If the jet of fluid is inadequate, firstly check that there is
fluid in the reservoir (see “Checking fluid levels” in this
chapter).
Then check that the nozzle holes are not clogged, if nec-
essary clean them using a needle.
The windscreen jets are directed by adjusting the nozzle
angle.
The jets should be directed at about a third of the height
from the top edge of the windscreen.
IMPORTANT In versions with a sun roof, make sure that
the sun roof is closed before operating the front jets.
fig. 8L0E0099m
Rear window washer fig. 9
The rear window washer jets are fixed. The nozzle holder
is on the rear window.
fig. 9L0E0100m

SERVICING AND MAINTENANCE249
5
Hard Black versions
Detergents pollute the environment. Only
wash the car in areas equipped for the col-
lection and purification of the fluids used in
the washing process.
Glasses
To clean glasses, use specific window cleaner products.
Also use clean cloths to avoid scratching the glass or dam-
aging the transparency.
IMPORTANT Wipe the rear window inside gently with
a cloth in the direction of the filaments to avoid damag-
ing the heating device.
Engine compartment
At the end of each winter, thoroughly wash the engine
compartment, taking care to avoid spraying the water jet
directly onto the electronic control units and the re-
lay/fuse control unit on the left side of the engine com-
partment (as you look from behind the wheel). Have this
operation performed at a specialised workshop.
IMPORTANT The washing should take place with the en-
gine cold and the ignition key in the STOP position. Af-
ter the washing operation, make sure that the various
protections (e.g. rubber caps and guards) have not been
removed or damaged.
Front headlights
IMPORTANT Never use aromatic substances (e.g.:
petrol) or ketones (e.g.: acetone) for cleaning the front
headlight plastic lenses.
In order to preserve the aesthetic appearance
of the paintwork abrasive products and/or pol-
ishes should not be used for cleaning the car.
IMPORTANT Bird droppings must be washed off imme-
diately and carefully as the acid they contain is particu-
larly aggressive.
It is recommended to avoid washing with
rollers and/or brushes in car wash stations.
Thus, wash the car only by hands using neu-
tral pH detergents; dry it with a wet chamois leather.
Abrasive products and/or polishes should not be used
for cleaning the car. Bird droppings must be washed
off immediately and thoroughly as the acid they con-
tain is particularly aggressive. Avoid (if possible) to
park your car under trees; remove immediately veg-
etable resins as, when dried, they could only be re-
moved with abrasive products and/or polishes that
are not recommended as they could possibly alter the
typical paint opacity. Do not use pure windscreen
washer fluid for cleaning the front windscreen and
rear screen; dilute it min. 50% with water.

57 –
8/10 –
6.0 –
3.1 2.65
3.5 3.0
1.99 1.8
–0.8
6–57 –
8/10 –
5,9 –
2.75 2.4
2.9 2.55
2.4 2.0
–0.8
6–
TECHNICAL SPECIFICATIONS269
6
Unleaded petrol not less than
95 R.O.N (EN228 specifications)
Mixture of demineralised
water and PARAFLU
UP
in 50-50 proportion (▲)
SELENIA K P.E.
SELENIA WR P.E. (❍)
TUTELA CAR MATRYX ()
TUTELA TRANSMISSION
GEARFORCE (❍)
TUTELA TOP 4
Water and liquid mixture
TUTELA PROFESSIONAL SC 35
CAPACITIES
(▲) When the vehicle is used in particularly harsh climate conditions, we recommend using a mixture of 60% PARAFLUUP
and 40% distilled water.
() 1.4 Turbo Jet 150 HP version
(❍) 1.4 Turbo Jet 120 HP and 1.4 Turbo Multi Air versions
1.4 Turbo Jet 1.4 Turbo MultiAir Recommended fuelslitres kg litres kg and original lubricants
Fuel tank:including a reserve of:
Engine cooling system:
Engine sump:Engine sump and filter:
Gearbox/differential casing:
Hydraulic brake circuit with ABS:
Windscreen/rear window washer
fluid reservoir:

57 –
8/10 –
7.1 –
4.3 3.6
4.9 4.1
3.1 2.7
–0.8
6–Diesel fuel for motor vehicles
(Specification EN590)
Mixture of 50% demineralised
water and 50% PARAFLU
UP(▲)
SELENIA WR P.E.
TUTELA CAR TECHNYX (❍)
TUTELA CAR MATRYX ()
TUTELA TOP 4
Water and liquid mixture
TUTELA PROFESSIONAL SC 35
57 –
8/10 –
7.1 –
4.3 3.6
4.9 4.1
1.87 1.7
–0,8
6–
270TECHNICAL SPECIFICATIONS
(▲) When the vehicle is used in particularly harsh climate conditions, we recommend using a mixture of 60% PARAFLUUPand
40% distilled water.
(❍) 1.6 Multijet version
() 1.9 Twin Turbo Multijet and 2.0 Multijet versions
1.6 Multijet 1.9 Twin Turbo Multijet Recommended fuels
2.0 Multijet and original lubricants
litres kg litres kg
Fuel tank:including a reserve of:
Engine cooling system:
Engine sump:Engine sump and filter:
Gearbox/differential casing:
Hydraulic brake circuit with ABS:
Windscreen/rear window washer
fluid reservoir:

SAE 75W-85 grade synthetic lubricant.
Exceeds API GL-4 PLUS specifications.
Classification 9.55550-MX3
SAE 75W grade synthetic base lubricant.
Classification 9.55550-MZ6
Synthetic based lubricant, grade SAE 75W-85.
Exceeds API GL-4 specifications.
Classification 9.55550-MZ1
Grease for constant-velocity joints with low
friction coefficient. NL.GI. 0-1 consistency
Classification 9.55580
Molybdenum disulphide grease
for high temperatures. NL.GI. 1-2 consistency
Classification 9.55580
Synthetic fluid for brake and clutch systems.
It exceedes the specifications: FMVSS no. 116 DOT 4,
ISO 4925, SAE J 1704. Classification 9.55597
Red protective with antifreeze action, based
on inhibited monoethyl glycol with organic formula.
Exceeding CUNA NC 956-16,
ASTM D 3306 specifications.
Additive for diesel fuel, protecting Diesel engines
Mixture of spirits and surfactants.
Exceeds CUNA NC 956-11 specifications.
Classification 9.55522
272TECHNICAL SPECIFICATIONS
TUTELA CAR TECHNYX Contractual Technical
Reference No. F010.B05
TUTELA TRANSMISSIONGEARFORCE
Contractual Technical
Reference No. F002.F10
TUTELA CAR MATRYX Contractual Technical
Reference No. F108.F02
TUTELA STAR 700
Contractual Technical
Reference No. F701.C07
TUTELA ALL STAR
Contractual Technical
Reference No. F702.G07
TUTELA TOP 4
Contractual Technical
Reference No.F001.A93
PARAFLU
UP(●)
Contractual Technical
Reference No. F101.M01
TUTELA DIESEL ARTContractual Technical
Reference No. F601.L06
TUTELA
PROFESSIONAL SC 35
Contractual Technical
Reference No. F201.D02 Brake fluid
Protective
agent for
radiators
Additive for
diesel fuel
Windscreen/
rear window
washer fluid
(
●) IMPORTANT Do not use fluids with different specifications for topping up or mixing.
(❑) When the vehicle is used in particularly harsh climate conditions, we recommend using a 60-40 mixture of PARAFLUUPand distilled water. Petrol
engine
lubricants
Gearboxes and manual
differentials
(1.6 Multijet versions)
Gearboxes and manual
mechanical (1.4 Turbo Jet
120 HP and 1.4 Turbo Multi
Air versions)
Gearboxes and manual
differentials (1.4 Turbo Jet
150 HP versions and Diesel
versions, 1.6 Multijet excluded)
CV joints differential side
CV joints wheel side
Hydraulic brakes and
hydraulically operated clutch
windscreen/rear window
washer/wiper
Cooling circuits.
Percentage of use:
50% water
50% PARAFLU
UP(❑)
To be mixed with diesel
(25 cc per 10 litres)
To be used diluted or undiluted
in windscreen/rear window
washer/wiper systems
Use Fluid and lubricant features for correct use of the car Genuine fluids and lubricants Applications