brake light Lancia Delta 2011 Owner handbook (in English)

REFUELLING
Petrol engines:exclusively refuel the car with un-
leaded petrol with a RON no lower than 95.
Diesel engines:refuel only with diesel fuel conform-
ing to the European specification EN590.
The use of other products or mixtures may damage the engine
beyond repair and consequently invalidate the warranty due
to the damage caused.
STARTING THE ENGINE
Petrol engines:make sure that the handbrake is en-
gaged, place the gear lever in neutral, fully depress the
clutch without depressing the accelerator, then turn the
ignition key to AV Vand release it as soon as the en-
gine has started.
Diesel engines:turn the ignition key to MARand wait for the
warning lights
Yandmto switch off; turn the ignition key
AVV and release it as soon as the engine starts.
PARKING ON FLAMMABLE MATERIAL
The catalytic converter develops high temperatures
during operation. Do not park the car on grass, dry
leaves, pine needles or other flammable material: fire
hazard.
RESPECTING THE ENVIRONMENT
The car is fitted with a system that allows continuous
diagnosis of the components correlated with emissions
to ensure better respect for the environment.ELECTRICAL ACCESSORIES
If, after buying the car, you decide to add electrical ac-
cessories (that may gradually drain the battery), visit
aLancia Dealership. They can calculate the overall
electrical requirement and check that the car’s elec-
tric system can support the required load.
CODE CARD
Keep the card in a safe place, not in the car. We rec-
ommend that you always carry the electronic code pro-
vided on the CODE card with you, in case you need
to perform an emergency start.
SCHEDULED SERVICING
Correct car maintenance is essential to ensure that the
performance, safety features, environmental friendli-
ness and low running costs are unchanged over the
years.
THE OWNER HANDBOOK CONTAINS…
... important information and warnings on the correct
use and maintenance of your car over time as well as
safe driving tips. Pay special attention to the symbols
"(personal safety) #(environmental protection)
â(car safety).
Refer to the “Instrument panel warning lights” chapter in this
handbook if the message “See Handbook” appears on the dis-
play.
READ THIS CAREFULLY!
K



1
KNOWING YOUR CAR9
SPEEDOMETER (SPEED INDICATOR) fig. 2-3
Indicator A shows the speed of the car.
REV COUNTER fig. 2-3
The indicator D shows the engine revs.
FUEL LEVEL GAUGE fig. 2-3
Indicator B shows the amount of fuel in the tank.
The
Kwarning light will switch on (together with a mes-
sage on the display) to indicate there are between 5 and
7 litres of fuel remaining.
Do not travel with the fuel tank almost empty: the gaps
in fuel delivery could damage the catalytic converter.
ENGINE COOLANT TEMPERATURE GAUGE
fig. 2-3
Gauge C shows the temperature of the engine coolant and
indicates when the coolant temperature exceeds 50 °C.
The first reference remains on constantly to indicate that
the system is operating correctly. The
uwarning light
switches on (together with a message on the display) to
indicate that the temperature of the engine coolant has
increased significantly. In this event, stop the engine and
go to a Lancia Dealership.INSTRUMENT PANEL WARNING LIGHTS
General warnings
The warning lights switch on together with a dedicated
message and/or a buzzer where appropriate. These in-
dications are brief and precautionary and as such must
not be considered as exhaustive and/or an alternative to
the information contained in the Owner Handbook,
which you are recommended to read carefully in all cases.
Always refer to the information in this chapter in the
event of a failure indication.
Low brake fluid level (red)
Turning the key to the MAR position the
warning light switches on, but it will switch
off after a few seconds. The warning light
comes on when the level of the brake fluid in the reser-
voir falls below the minimum level due to a possible leak
in the circuit.
The display shows the dedicated message.
Handbrake on (red)
When the key is turned to the MAR position the warn-
ing light comes on but should go out after a few seconds.
The warning light turns on when the handbrake is en-
gaged. If the car is moving the buzzer will also sound.
IMPORTANT If the warning light turns on when travel-
ling, make sure that the handbrake is not engaged.
x

10KNOWING YOUR CAR
If the xwarning lightturns on when travel-
ling (with the message on the display) stop
the car immediately and contact a Lancia
Dealership.
Brake pad wear (amber)
The warning light (or symbol on the display)
switches on when the front brake pads show
signs of wear; under these circumstances have
them replaced as soon as possible. The display shows the
dedicated message.
IMPORTANT Because the car is equipped with a wear de-
tection system only for the front brake pads, when these
are replaced the rear brake pads should also be checked
for wear.
d
Airbag failure (red)
When the key is turned to the MAR position
the warning light comes on but should go out
after a few seconds. The warning light stays on
constantly if there is a failure in the air bag system.
The display will show a dedicated message.
¬
If the ¬warning light does not come on
when the key is turned to MAR or if it stays
on with the car in motion (together with the
message on the display) there could be a fault in the
restraint systems; under these circumstances, the
air bags or pretensioners may not be deployed in
the event of an impact or, more rarely, they could
be deployed accidentally. Before continuing your
journey, contact a Lancia Dealership to have the
system checked immediately.
The failure of warning light ¬is indicated
by warning light
“flashing for longer than
the usual four seconds, thus signalling that
the front passenger airbag is deactivated. In ad-
dition, the air bag system automatically disables
the air bags on the passenger side (both front and
side air bags). In this case, the warning light
¬
may not indicate failures in the retaining system.
Contact a Lancia Dealership immediately to have
the system checked.
EBD failure (red)
If warning lightsxand>are on at the same
time with the engine running, this indicates
an EBD system failure or that the system is
not available. Early locking of the rear wheels
may occur in the event of sharp braking, pos-
sibly causing the car to swerve.
Drive very carefully to a Lancia Dealership to
have the system inspected immediately. The display will
show a dedicated message.
x
>

20KNOWING YOUR CAR
Particularly strong radio frequency interfer-
ence may cause the T.P.M.S. system to func-
tion incorrectly. This condition is indicated
to the driver by a message (for versions/markets
where provided).
The message will disappear automatically as soon
as the interference ceases to disturb the system.
Exterior lights failure (amber)
This warning light (or symbol on the display)
switches on when a failure is detected in any
of the following lights:
❍side lights;
❍brake lights (for versions/markets where provided);
❍rear fog lamps;
❍direction indicators;
❍number plate lights;
❍day lights.
The failure relating to these lights could be: one or more
blown bulbs, a blown protection fuse or a break in the
electrical connection.
The display shows the dedicated message.
W
Rear fog lamps (amber)
The warning light switches on activating the
rear fog lamps.
4
Front fog lights (green)
The warning light comes on when the front fog
lights are turned on.
5
Direction indicators
(green – intermittent)
The warning lights switch on when the direc-
tion indicator control lever is moved down-
wards, upwards or when the hazard warning
light button is pressed.
F
D
Day lights/dipped beam headlights
(green)
This warning light switches on when the day
lights or dipped beam headlights are activated.
Follow me home
This warning light comes on when this device is activated
(see “Follow me home”).
The display will show a dedicated message.
3

1
KNOWING YOUR CAR35
Possible presence of ice on the road
The outside temperature indicator starts
flashing when the outside temperature reaches
or falls below 3 °C and the
❄symbol lights up
on the display to warn the driver of the possible presence
of ice on the road.
The display will show a dedicated message.Adaptive lights not available
The display shows the dedicated message when
the adaptive lights system is not available.
Contact a Lancia Dealership. Exterior lights failure (amber)
The symbol switches on in the display when
a fault is detected in the brake lights.
The display shows the dedicated message.
W
❄
Driving advisor on
The display shows a dedicated message when
the driving advisor function is switched on.
ef
Steering corrector not available
(DST – Dynamic Steering Torque)
The display shows a dedicated message when
the steering corrector is faulty. Contact a Lancia
Dealership.
è
Service deadline
The display shows a specific message to indi-
cate the scheduled servicing deadline.
Speed limit exceeded
The display shows a dedicated message when the preset
speed limit is exceeded (for Arab countries the speed limit
is set at 120 km/h). The icon shown on the display rep-
resents the set speed limit.
õ

1
KNOWING YOUR CAR69
When travelling downhill with the device engaged, the
vehicle speed may slightly exceed the preset one.
The engagement of the device is signalled by the Üwarn-
ing light coming on in the instrument panel (together
with a message shown on the display) (see “Instrument
panel warning lights” paragraph in this chapter).
STORING THE SPEED
Proceed as follows:
❍turn the ring nut A-fig. 31 to ON and press the ac-
celerator until the vehicle reaches the desired speed;
❍turn the ring nut to (+) for at least three seconds, then
release it. The vehicle speed is now memorised and
you can therefore release the accelerator pedal.
If needed (when overtaking for instance), you can accel-
erate simply by pressing the accelerator pedal; when you
come off the pedal, the car will return to the speed mem-
orised previously.
RESTORING THE MEMORISED SPEED
If the device has been switched off, for example by de-
pressing the brake or clutch pedal, the memorised speed
can be restored as follows:
❍accelerate gradually until reaching a speed ap-
proaching the memorised speed;
❍engage the gear selected at the time of speed memo-
rising (fourth, fifth or sixth gear);
❍press button C-fig. 31.INCREASING THE MEMORISED SPEED
This can be done in two ways:
❍by pressing the accelerator and then memorising the
new speed reached;
or
❍by temporarily turning ring nut B-fig. 31 to (+).
Each movement of the selector wheel will correspond to
a slight increase in speed (about 1 km/h), while keeping
the selector wheel turned will correspond to a continuous
speed increase.
REDUCING THE MEMORISED SPEED
This can be done in two ways:
❍by disengaging the device and then memorising the
new speed;
or
❍by keeping ring nut B-fig. 31 turned to (–) until the
new speed is reached; it will then be memorised au-
tomatically.
Each movement of the ring nut will corresponds to
a slight reduction in speed (about 1 km/h), while keep-
ing the ring nut turned will correspond to a continuous
reduction in speed.

70KNOWING YOUR CAR
TURNING THE DEVICE OFF
Turn the ring nut A-fig. 31 to OFF or turn the ignition
key to STOP. The device is automatically turned off in
one of the following cases:
❍when the brake or clutch pedal is pressed;
❍if the ASR or Advanced ESP system cuts in (for ver-
sions/markets where provided).
While travelling with the device engaged, do
not place the gear lever in neutral.
In case of malfunction or if the device is
faulty, turn the control A-fig. 31 to OFF and
contact a Lancia Dealership, after checking
that the protective fuse has not blown.
ROOF LIGHTS
FRONT ROOF LIGHT WITH SPOT LIGHTS fig. 32
Switch A is used to switch on/off roof lights.
With the switch A in the middle position, the lights C and
D go on/off when front doors are opened/closed.
With switch A pressed to the left, the lights C and D are
always off. With switch A pressed to the right, the lights
C and D are always on.
Lights switch on/off progressively.
Switch B controls the spot light function; when the roof
light is off, it switches on individually:
❍the light C when pressed to the left;
❍the light D when pressed to the right.
fig. 32L0E0024m

112KNOWING YOUR CAR
ADVANCED ESP SYSTEM
(ELECTRONIC STABILITY PROGRAM)
This is an electronic car stability control system in the
event of tyre grip loss, helping to maintain directional
control.
The Advanced ESP system is therefore particularly use-
ful when road surface grip conditions change.
With the Advanced ESP system as well as the ASR (trac-
tion control with intervention on the brakes and the en-
gine) plus the HILL HOLDER (device for hill starts with-
out using the brakes) and also MSR (adjustment of engine
braking force with gear downshift), HBA (automatic in-
crease in braking pressure during emergency braking),
ABS (preventing the wheels from locking and slipping on
all road surfaces during sharp braking and DST (appli-
cation of force on the steering wheel for steering correc-
tion) functions are all available. SYSTEM INTERVENTION
It is signalled by the blinking of the warning light á
on the instrument panel, to inform the driver that the car
is in critical stability and grip conditions.
Switching the system on
The Advanced ESP system comes on automatically when
the vehicle is started and cannot be turned off.
Failure indications
In the event of a failure, the Advanced ESP system will
be automatically switched off and warning light áwill
appear constantly in the instrument panel along with
a message on the reconfigurable multifunction display.
The LED on the ASR OFF button will also light up (see
“Instrument panel warning lights” chapter). In this case,
go to a Lancia Dealership.
The performance of the Advanced ESP sys-
tem should not encourage the driver to take
unnecessary risks. Your driving style must
always be suited to the road conditions, visibility
and traffic. The driver is ultimately responsible for
road safety.

1
KNOWING YOUR CAR113
Failure indications
System failure is indicated by warning light
álighting
up in the instrument panel together with a dedicated mes-
sage appearing in the reconfigurable multifunction dis-
play; see “Instrument panel warning lights” chapter.
IMPORTANT The Hill Holder system is not a parking
brake; therefore, never leave the car without having en-
gaged the handbrake, turned the engine off and engaged
first gear.
The Advanced ESP system continues to oper-
ate if the space-saver wheel is fitted. Always
remember that the space-saver wheel, being
smaller than the original wheel provides less grip.
For the correct operation of the Advanced ESP and
ASR systems, the tyres must absolutely be the same
make and type on all wheels, in perfect conditions
and, above all, of the type, make and size specified.
HILL HOLDER SYSTEM
This is an integral part of the Advanced ESP system and
automatically cuts in in the following conditions:
❍uphill: car at a standstill on a road with a gradient
higher than 5%, engine running, clutch and brake
pedal pressed, gearbox in neutral or engaged gear
other than reverse.
❍downhill: car at a standstill on a road with a gradi-
ent higher than 5%, engine running, clutch and brake
pedal pressed and reverse gear engaged.
When setting off, the Advanced ESP system control unit
will keep braking pressure on the wheels until reaching
the required power for starting or, in any case, for a max-
imum of 2 seconds in order to move the right foot from
the brake pedal to the accelerator pedal easily.
When two seconds have elapsed, without starting, the
system is automatically deactivated, gradually releasing
the braking pressure. During this release stage, the typi-
cal mechanical brake release noise can be heard, indi-
cating that the car is about to move.

116KNOWING YOUR CAR
SYSTEM INTERVENTION
The driver can tell the ABS system has come into action
because the brake pedal pulsates slightly and the system
gets noisier: it means that the vehicle speed should be al-
tered to suit the type of road surface.FAILURE INDICATIONS
ABS failure
This is signalled by the >warning light in the instru-
ment panel coming on together with a message in the re-
configurable multifunction display. In this case, the brak-
ing system will still be effective, although without the
extra capacity offered by the ABS system. Drive carefully
to the nearest Lancia Dealership to have the system
checked.
EBD failure
This is signalled by the >andxwarning lights on the
instrument panel coming on, together with a message on
the reconfigurable multifunction display. In this case, the
rear wheels may suddenly lock and the vehicle may
swerve when braking sharply. Drive very carefully to the
nearest Lancia Dealership to have the system checked.
When the ABS cuts in and you feel the brake
pedal pulsating, do not release the pressure,
but keep it pressed; in doing so you will stop
in the shortest amount of space possible depend-
ing on the current road conditions.
If the ABS system cuts in, it means that the
grip between the tyre and the road surface is
close to its limit: you must slow down to
match the speed to the road grip available. The
ABS make the best use of the available grip but
cannot increase it.
You should always drive carefully on slip-
pery surfaces and avoid any unnecessary
risks.
If only warning light xon the instrument
panel comes on, with a message in the re-
configurable multifunction display, stop the
car immediately and contact the nearest Lancia
Dealership. Leakage of hydraulic fluid from the
braking system will compromise the operation of
the braking system, whether it is of the conven-
tional type or with ABS.