rims Lancia Delta 2011 Owner handbook (in English)
[x] Cancel search | Manufacturer: LANCIA, Model Year: 2011, Model line: Delta, Model: Lancia Delta 2011Pages: 290, PDF Size: 8.36 MB
Page 194 of 290
IN AN EMERGENCY193
4
REPLACING A WHEEL
GENERAL INSTRUCTIONS
The car may be originally fitted with a space-saver wheel
(for versions/markets, where provided).
Wheel changing and correct use of the jack and spare
wheel call for some precautions as listed below.
The space-saver wheel (for versions/mar kets
where provided) is specific to your car, do not
use it on other models, or use the spare wheel
of other models on your car. The space-saver wheel
must only be used in case of emergency. Never use
it for more than strictly necessary and never exceed
80 km/h. On the space-saver wheel there is an or-
ange label, summarising the main warnings re-
garding space-saver wheel usage restrictions.
Never remove or cover the label. Never ap-
ply a hub cup on a space-saver wheel. The
following information is provided in four
languages on the label: IMPORTANT! FOR TEM-
PORARY USE ONLY! 80 KM/H MAX.! REPLACE
WITH STANDARD WHEEL AS SOON AS POS-
SIBLE. DO NOT COVER THIS LABEL.
If you change the type of wheel (alloy rims instead
of steel rims) you will have to change the entire set
of fastening bolts with another set of suitably sized
bolts.
Alert other drivers that the car is stationary
in compliance with local regulations: haz-
ard warning lights, warning triangle, etc.
Any passengers on board should leave the car, es-
pecially if it is heavily laden. Passengers should
stay away from on-coming traffic while the wheel
is being changed. If parked on a slope or rough sur-
face, chock the wheels with wedges or other suit-
able devices.
Page 200 of 290
IN AN EMERGENCY199
4
REFITTING THE STANDARD WHEEL
Following the procedure described previously, raise the
car and remove the space saver spare wheel.
Versions with steel rims
Proceed as follows:
❍make sure the contact surfaces between standard
wheel and hub are clean so that the fastening bolts
will not come loose;
❍fit the standard wheel inserting the 4 bolts into the
holes;
❍using the wrench provided, tighten the fastening bolts;
❍press-fit the hub cap, aligning the special splining (on
the cap) with the inflation valve;
❍lower the car and remove the jack;
❍using the wrench provided, fully tighten the bolts in
the sequence shown previously.Versions with alloy wheels
❍Place the wheel onto the hub and tighten the bolts us-
ing the wrench provided;
❍lower the car and remove the jack;
❍using the spanner provided, fully tighten the bolts in
the sequence shown in fig. 8;
❍refit the press-fitted hub cap, making sure that the
reference hole on the wheel is aligned with the refer-
ence pin on the cap.
IMPORTANT If it is not fitted properly, the hub cap may
detach when the vehicle is running.
Page 201 of 290
200IN AN EMERGENCY
After tyre replacement
❍Stow the space saver wheel D-fig. 10 in the space pro-
vided in the luggage compartment;
❍fit the partially open jack in its box forcing it lightly
to prevent it from vibrating when travelling;
❍put the tools back into place in the container;
❍stow the container, complete with tools, in the spare
wheel and tighten the locking device B-fig. 10;
❍reposition the boot mat correctly.
IMPORTANT Do not use inner tubes with tubeless tyres.
Check the inflation pressure of the tyres and the space-
saving wheel periodically.CHANGING A BULB
GENERAL INSTRUCTIONS
❍Before changing a bulb, check the contacts for rust-
ing;
❍burnt-out bulbs must be replaced by others of the
same type and wattage;
❍always check the alignment of the beam after chang-
ing a headlight bulb;
❍when a light is not working, check that the corre-
sponding fuse is intact before changing a bulb. For the
location of fuses, refer to the paragraph “Replacing
fuses” in this chapter.
Modifications or repairs to the electric sys-
tem that are not carried out properly or do
not take the system technical specifications
into account can cause malfunctions leading to the
risk of fire.
Various fastening bolts and space-saver
wheels, specific and differing in structural
characteristics, are used depending on the
wheel rim type (alloy or steel). Fastening bolts for
alloy rims can be identified by the presence of a per-
manent washer and a hollow side on the bolt head.
Therefore, you will need to go to a Lancia Dealer-
ship to get the correct type of fastening bolts and
space saver wheel if you change the type of wheels
fitted (alloy rims instead of steel rims, or vice
versa). Keep the bolts fitted as standard in case of
re-use of the wheels originally mounted on the car.
Page 244 of 290
SERVICING AND MAINTENANCE243
5
❍when replacing the tyres, always fit new tyres, avoid-
ing those of dubious origin;
❍If a tyre is replaced, you should also change the in-
flation valve;
❍to allow even wear between the front and rear tyres,
it is advisable to switch them every 10-15 thousand
kilometres, keeping them on the same side of the car
so as not to reverse the direction of rotation.
Remember that the road holding qualities of
your car also depend on the correct inflation
pressure of the tyres.
If the pressure is too low the tyre will get
overheated, with the risk of serious damage
to the tyre.
Avoid moving the tyres from the right side
of the vehicle to the left side and vice versa.
Do not repaint alloy wheel rims at temper-
atures higher than 150 °C. The mechanical
specifications of the wheels might be ad-
versely affected.
Page 255 of 290
254TECHNICAL SPECIFICATIONS
198A4000
198A1000
198A7000
198A2000
955A4000 (
▲)
844A1000
198A5000
844A2000 (
▲)
844AXA1A 00E
844AXA1A 00F (*)
844AXB1A 01C ()
844AXB1A 01D (*) ()
844AXL1A 10
844AXL1A 10B (*)
844AXC1A 02E
844AXC1A 02F (*)
844AXF1A 06E (
❏)
844AXF1A 06F (*)
844AXE1A 04C
844AXE1A 04D (*)
844AXD1A 03C
844AXD1A 03D (*)
844AXG1A 08 (
❏)
844AXG1A 08B
ENGINE CODES – BODYWORK VERSIONS
ENGINE CODE BODYWORK VERSION
1.4 Turbo Jet 120 HP
1.4 Turbo Jet 150 HP
1.4 Turbo Multi Air
1.6 Multijet
1.9 Twin Turbo Multijet
2.0 Multijet
() EURO 4 version
(*) Versions with 18" rims
(
▲) For versions/markets where provided
(
❏) Version without DPF
Page 261 of 290
260TECHNICAL SPECIFICATIONS
WHEELS
RIMS AND TYRES
Pressed steel or alloy rims. Tubeless radial carcass tyres.
All approved tyres are listed in the Vehicle Registration
Document.
IMPORTANT In the event of discrepancies between the
information provided in this “Owner’s handbook” and
the “Registration Document”, consider the specifications
shown in the log book only.
For safe driving, the car must be fitted with tyres of the
same make and type on all wheels.
IMPORTANT Do not use inner tubes with Tubeless tyres.
SPACE-SAVER WHEEL
Pressed steel wheel. Tubeless tyre.
WHEEL GEOMETRY
Total front toe in: –1
±1 mm
Total rear toe in: 2
±2 mm
The figures refer to the car in running order.UNDERSTANDING TYRE MARKING fig. 5
Example: 195/55 R 16 91 V
195 = Nominal width (S, distance in mm between
sidewalls).
55 = Height/width ratio (H/S) as a percentage.
R = Radial tyre.
16 = Rim diameter in inches (Ø).
91 = Load rating (capacity).
V = Maximum speed index.
fig. 5L0E0120m
Page 264 of 290
TECHNICAL SPECIFICATIONS263
6
7Jx16"- ET31
7Jx17"- ET31
7.5Jx18"- ET354Bx15" H-ET 35 (*) 125/90 R15-96M (*)
(*) Depending on the trim level, the space-saver for the 1.9 Twin Turbo Multijet and the 2.0 Multijet has a 205/55 R16-91V tyre
and a 7Jx16"-ET31 rim. In this case the 205/55 R16 91V tyre has the same specifications as the space-saver: the information
in “Replacing a wheel” therefore refers to the 205/55 R16 91V tyre.
(
❏) Tyre to which chains cannot be fitted.
205/55 R16-91V
225/45 R17-91W
225/40 R18-92W
(❏)
205/55 R16-91T (M+S)
225/45 R17-91T (M+S)
225/40 R18-92T (M+S)
On 205/55 R16-91V tyres, use reduced size snow chains with a maximum projection of 9 mm beyond
the tyre profile. On 225/45 R17-91W tyres, use reduced size snow chains with a maximum projec-
tion of 7 mm beyond the tyre profile.
IMPORTANT Special techniques need to be adopted for 225/40 R18 92W tyres. For this reason, this tyre can only
be ordered when the car is purchased. Do not fit this tyre after the vehicle has been purchased!
Versions Rims Tyres Snow tyres Space-saver
(for versions/markets, where provided)
Rim Tyre
1.4 Turbo Jet
1.4 Turbo
Multi Air
1.6 Multijet
1.9 Twin
Turbo Multijet
2.0 Multijet
Page 266 of 290
TECHNICAL SPECIFICATIONS265
6
fig. 6
L0E0101m
DIMENSIONS
452010172700
(*) Small variations in size are possible depending on the dimensions of the rims1499 (*)15381531
Boot capacity
Capacity with vehicle unladen (VDA standards) ............................. 380 dm
3
Maximum capacity ...........................................................................465 dm3
Dimensions are expressed in mm and refer to the car equipped with its the tyres
supplied. Height is measured with car unladen.
1797
ABCDEFGH
803
Page 284 of 290
LIST OF CONTENTS283
7
Warning lights on panel ..... 9
Weights ...............................267
Wheel (changing) ................193
Wheel rims
– reading rim markings .....262
Wheels ................................260
When parked ......................175
Window cleaning washer ...... 65
Windows (cleaning) ............249
Windscreen wipers
– blades .............................245
– control ............................ 65
– nozzles ...........................246