fuse Lancia Musa 2007 Owner handbook (in English)

TO REDUCE MEMORISED SPEED
The speed memorised can be increased in two ways:
❒disengaging the device and then memorising the
new speed;
or
❒moving the stalk downwards (–) until reaching
the new speed which will be memorised
automatically.
Each operation of the stalk will correspond to a
slight reduction in speed (about 1 km/h), while
keeping the stalk downwards continuously will
correspond to a continuous speed reduction.DEVICE DISENGAGEMENT
Turn the ring A to OFF or the ignition key to STOP.
The device is automatically deactivated also in one
of the following cases:
❒pressing the brake or clutch pedal.
111
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
WARNING
WARNING
In the event of device malfunction or failure, turn the knurled ring A to OFF and
contact a Lancia Dealership after checking the protective fuse integrity. When travelling with the device on, do not put the gearbox lever in neutral.

FAILURE WARNINGS
Any electric power steering failure is indicated by
cluster warning light gcoming on (together, with
the message on the multifunction display - see the
“Warning lights” chapter).
In the event of electric power steering failure, the
car can be driven with mechanical steering to the
closest Lancia Dealership.IMPORTANT The steering may become slightly stiff
following parking manoeuvres including a great
deal of steering. This is normal and caused by the
system to prevent motor overheating. No servicing is
required. The electrical power steering system will
return to normal operation the next time the car is
used.
151
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
WARNING
Always switch the engine off, remove the key from the starting device and actuate
the steering lock before carrying out any maintenance operation, especially when
the wheels are raised from the ground. In case this is not possible (e.g. when the
key must be in MAR position or the engine running), remove the electric power
steering main fuse before carrying out any maintenance operation.

210
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
EBD SYSTEM FAILURE - SYSTEM
UNAVAILABLE ..................................................... 239
EXTERNAL LIGHT FAILURE.............................. 240
BRAKE LIGHT FUSE FAILURE ........................... 242
PARKING SENSOR FAILURE ............................... 242
ANTIPINCH SYSTEM
FAILURE............................................................... 243
AIR BAG FAILURE ............................................... 244
TWILIGHT SENSOR FAILURE ............................ 245
INJECTION SYSTEM FAILURE............................ 245
ENGINE CONTROL SYSTEM FAILURE
(EOBD) ................................................................. 246
GENERIC FAILURE INDICATION........................ 247
“DUAL FUNCTION SYSTEM”
TRANSMIS. FAIL. ................................................. 248
ESP SYSTEM FAILURE -
SYSTEM NOT AVAILABLE .................................. 249
HILL HOLDER FAILURE -
SYSTEM NOT AVAILABLE .................................. 250

240
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
EXTERNAL LIGHT FAILURE
The warning light on the dial turns on (together with the message on
the display) when one of the following failures is detected: broken
circuit, “missing” or burnt-out bulb, wrong bulb power. Light check
concerns: taillights, brake lights (3rd stop light excluded), rear fog
lights, headlights, direction indicators and number plate lights.
The failure referring to these lights could be: one or more blown
bulbs, a blown protection fuse or a cut-off electric connection.
Symbols
¯/˙(where provided) coming on on the display indicate a
left/right-hand light failure.
W
amber
continued
Warning
light on
dialMessage on
multifunction
display

241
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
WEXTERNAL LIGHT FAILURE
The warning light on the dial turns on (together with the message on
the display) when one of the following failures is detected: broken
circuit, “missing” or burnt-out bulb, wrong bulb power. Light check
concerns: taillights, brake lights (3rd stop light excluded), rear fog
lights, headlights, direction indicators and number plate lights.
The failure referring to these lights could be: one or more blown
bulbs, a blown protection fuse or a cut-off electric connection.
Symbols¯/˙coming on on the display indicate a left/right-hand
light failure.amber
continued from previous page
(*)
(*) Or rear
Warning
light on
dial Message on
multifunction
display

242
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
BRAKE LIGHT FUSE FAILURE
The warning light on the dial turns on (together with the message on
the display) when the brake light fuse is faulty (blown fuse).
W
T.P.M.S. FAULT WARNING LIGHT (where provided)
The warning light comes on (together with the message on the display
and the buzzer), when T.P.M.S. (where provided) fault is detected.
Contact Lancia Dealership as soon as possible.
Should one or more wheels without sensor be fitted, the instrument
panel warning light will come on (together with the message on the
display) and stay on until restoring initial conditions.
è
amber
amber
Warning
light on
dialMessage on
multifunction
display

251
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IN AN EMERGENCY
DOOR OPENING/CLOSING ................................. 252
ENGINE STARTING ............................................. 253
QUICK TYRE REPAIR KIT
FIX & GO automatic ............................................... 256
IF A TYRE IS PUNCTURED ................................. 261
WHEN NEEDING TO CHANGE A BULB ............ 268
IF AN EXTERIOR LIGHT BURNS OUT ............... 271
IF AN INTERIOR LIGHT BURNS OUT ................ 277
IF A FUSE BLOWS ............................................... 280
IF THE BATTERY IS FLAT .................................. 286
JACKING THE CAR .............................................. 287
TOWING THE CAR ............................................. 287

268
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
WHEN NEEDING TO
CHANGE A BULB
GENERAL INSTRUCTIONS
❒When a light is not working, check that it has
not fused before changing the bulb. For the
location of the fuses, refer to “If a fuse blows” in
this chapter;❒Before replacing a bulb that does not work,
check that the contacts are not oxidised;
❒Burnt bulbs must be replaced by others of the
same type and power;
❒Always check the height of the headlight beam
after changing a bulb.
Only touch the metal part when handling halogen bulbs. If the transparent bulb is touched it
reduces the intesity of the light emitted and can also reduce the life of the bulb. If you touch the
bulb accidentally, rub it with a cloth moistened with alcohol and leave it to dry.
WARNING
Modifications or repairs to the electrical system carried out incorrectly and
without bearing the features of the system in mind can cause malfunctions with
the risk of fire.
WARNING
Halogen bulbs contain pressurised gas which, if broken, may cause small
fragments of glass to be projected outwards.

280
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IF A FUSE BLOWS
GENERAL
The fuse is a protective device for the electric system: it comes into
action (i.e. it cuts off) mainly due to a fault or improper action on the
system.
If an electric device is not working, check the efficiency of its fuse.
The conductor element A must be intact; if not, replace the fuse with
one of the same amp rating (same colour).
B: Undamaged fuse
C: Fuse with broken filament.
Remove the blown fuse using the pincer D provided in the control box
on the dashboard.
Never replace a broken fuse with anything other than a new fuse.
WARNING
WARNING
If a general fuse (MEGA-FUSE, MIDI-FUSE, MAXI-FUSE) cuts in, do not
attempt any repair and contact Lancia Dealership. Before changing a fuse, check
the ignition key has been removed and that all the other electric devices have been
turned off/disabled.
If the fuse blows again, have the car inspected at Lancia Dealership.
WARNINGNever change a fuse with another with a higher amp rating, DANGER OF FIRE.
L0D0198m

281
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
FUSE LOCATION
Fuses are grouped into two fuse boxes to be found respectively on the
left side of the dashboard and in the engine compartment near the
battery.
Fuse box on the dashboard
To access the dashboard fuse box, loosen retainers A and remove
protection panel B.
L0D0199m
L0D0200m