run flat Lancia Musa 2007 Owner handbook (in English)

USING THE MECHANICAL GEARBOX
To engage the gears, press the clutch pedal fully and shift the gear
lever into one of the required positions (the diagram is shown on the
knob).
IMPORTANT The car can only be put into reverse gear when it has
stopped moving completely. With the engine running, before engaging
the reverse, wait at least 2 seconds with the clutch pedal fully down to
prevent damage and grating of the gears.
To engage 6
thgear (where required), press the lever to the right to
prevent engaging 4thgear by mistake. A similar action is required to
shift down from 6th to 5th.
To engage reverse (R) from neutral, lift the sliding ring (A) under the
knob and shift the lever to the right and back (only for petrol
versions).
For Multijet versions, just shift lever to the right and back.
188
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
L0D0150m
To change gears properly you must push the clutch pedal fully down. It is therefore
essential that there is nothing under the pedals: make sure mats are lying flat and do
not get in the way of the pedals.
WARNING
Do not drive with your hand resting on the gear lever as the force exerted, even if slight, could lead
over time to premature wear on the gearbox internal components.
L0D0360m

257
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
IMPORTANT Do not use the quick repairing kit if
the tyre is damaged due to driving with the wheel
flattened.IT SHOULD BE NOTICED THAT:
The sealing fluid of the quick tyre repair kit is
effective with external temperatures between –20 °C
and +50 °C.
The sealing fluid has limited life.
In the event of a puncture caused by foreign bodies, it is possible to repair tyres showing damages
on the track or shoulder up to max 4 mm diameter.
The compressor shall not be operated for more than 20 minutes. Risk of
overheating!. Tyres repaired with the quick tyre repair kit shall be used
temporarily only.WARNING
Repairs are not possible in case of damages on the wheel rim (bad groove
distortion causing air loss). Do not remove foreign bodies (screws or nails) from
the tyre.WARNING
Holes and damages on the tyre side walls cannot be repaired. Do not use the
quick tyre repair kit if damaging is due to running with flat tyre.WARNING

258
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
INFLATING PROCEDURE
❒Pull up the handbrake. Loosen tyre inflation valve cap, take out the
filler hose A and screw the ring nut B on the tyre valve;
L0D0363m
Put on the protection gloves provided together with quick tyre repair kit.WARNING
Replace the cylinder if sealer has run out. Do not throw away the cylinder and the sealing fluid.
Have the sealing fluid and the cylinder disposed of in compliance with national and local
regulations.
WARNINGThe cylinder contains ethylene glycol. The cylinder contains latex: it can cause
allergic reactions. It is harmful if ingested or inhaled and irritant for the eyes and
in case of contact. In case of contact rinse immediately with water and take off
contaminated clothes. If swallowed, do not induce vomit, rinse out the mouth,
drink a lot of water and call the doctor immediately. Keep away from children.
This product must not be used by asthmatics. Do not inhale vapours. Call the
doctor immediately in case of allergic reactions. Keep the cylinder in the space
provided for the purpose and far from heat. The sealing fluid has limited life.

260
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
IN AN
EMERGENCY
It is of vital importance to communicate that the tyre has been repaired using the
quick tyre repair kit. Hand the instruction brochure to the personnel charged with
treating the tyre repaired with the kit.WARNING
❒if reaching the tyre pressure specified in paragraph “Inflation pressure”
in section “Technical Specifications”, start driving immediately;
❒after driving for about 10 minutes stop and check again the tyre pres-
sure; pull up the handbrake;
❒if at least 1.8 bar pressure is read, restore proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the nearest Lancia Dealership.
FOR CHECKING AND RESTORING PRESSURE ONLY
The compressor can be also used just for restoring pressure.
Disconnect the quick connection and connect it directly to the tyre
valve; in this way the cylinder is not connected to compressor and the
sealing fluid will not flow into the tyre.
CYLINDER REPLACEMENT PROCEDURE
To replace the cylinder proceed as follows:
❒disconnect connection A;
❒turn counter-clockwise the cylinder to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection A to the cylinder and fit the transparent tube B in-
to the proper space.
L0D0367m
L0D0368m