tow Lancia Musa 2007 Owner handbook (in English)
[x] Cancel search | Manufacturer: LANCIA, Model Year: 2007, Model line: Musa, Model: Lancia Musa 2007Pages: 346, PDF Size: 5.15 MB
Page 23 of 346

22
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Never remove the ignition key while the car is moving. The steering wheel would
automatically lock as soon as you try to turn it. This also applies when the car is
being towed.
WARNING
STEERING COLUMN LOCK
Engaging
When the key is to STOP remove the key and turn
the steering wheel until it locks.Disengaging
Rock the steering wheel slightly as you turn the
ignition key to MAR.
Page 70 of 346

69
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
WARNING
Any adjustment of the steering wheel position must be carried out only with the
car stationary and the engine turned off.
STEERING WHEEL ADJUSTMENT
The steering wheel can be adjusted both in height A and axially B.
Proceed as follows:
❒release the lever pulling it towards the steering wheel (position 2);
❒adjust the steering wheel as required;
❒lock the lever pushing it forwards (position 1).
L0D0055m
WARNING
It is absolutely forbidden to carry out whatever after-market operation involving
steering system or steering column modifications (e.g.: installation of anti-theft
device) that could badly affect performance and safety, cause the lapse of
warranty and result in car non-compliance with the regulations in force.
Page 93 of 346

92
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
To switch the function off, simply turn the
temperature knob counterclockwise and set the
required temperature.
❒LO function (highest cooling power):
this is activated by turning the temperature knob
counterclockwise below the min. value (16 °C). It
can be activated independently from the driver’s or
passenger’s side or both (also selecting the MONO
function).
This function can be engaged when requiring to
cool the passenger compartment as quickly as
possible, exploiting the maximum potential of the
system. This function engages inside air
recirculation and climate control compressor, while
air distribution and fan speed are controlled
according to environmental conditions. All manual
settings are however possible with this function on.
To switch the function off, simply turn the
temperature knob clockwise and set the required
temperature.Front air distribution
selection buttons
I-M
Pressing the relevant
buttons it is possible to
manually choose one of the five possible air
distributions to the left and right side of the
passenger compartment:
▲Air flow to the windscreen and front side window
vents to demist or defrost them.
˙Air flow to dashboard central and side vents to
provide satisfactory ventilation to the chest and
face, specially during the summer.
▼Air flow towards the front and rear lower parts of
the passenger compartment. Due to the natural
tendency of heat to spread upwards, this type of
distribution allows heating of the passenger com-
partment in the shortest time, also giving a prompt
feeling of warmth to the coldest parts of the body.
˙
▼Splitting of the air flow between the vents to the
lower part of the passenger compartment
(warmest air) and the dashboard centre and side
outlets (coolest air). This air flow distribution is
particularly useful in spring and autumn, when
the sun is shining.
▲
▼Splitting of the air flow between the lower part of
the passenger compartment and the windscreen
and front side window demisting/defrosting vents.
This type of air distribution allows satisfactory
heating of the passenger compartment while pre-
venting possible misting of the windows.
Page 94 of 346

93
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
Set air flow distribution is indicated by the
corresponding button led switching on.
With a combined function set, pressing a button will
turn on the main function of the button pressed,
together with the functions set yet. Pressing the
button of the active function will turn the function
off (led off).
To restore automatic air distribution control after a
manual selection, press button AUTO.
When the driver selects air distribution towards the
windscreen, also the air distribution on passenger’s
side will automatically be directed to the
windscreen. The passenger can however select a
different air distribution by pressing the relevant
buttons.Fan speed adjustment buttons L
Pressing the ends of button p
increases or decreases the fan speed
and therefore the amount of air
admitted to the passenger
compartment, although keeping the required
temperature.
The fan speed is shown by the lit bars on the
display
❒max fan speed = all bars lit
❒min fan speed = one bar lit.
The fan can be cut off only if the climate control
compressor has been switched off pressing button B.
IMPORTANT To restore automatic fan speed
control after a manual adjustment, press button
AUTO.
Page 101 of 346

100
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
MAIN BEAM HEADLIGHTS
When the knurled ring is at 2pull the lever towards the steering
wheel (stable position).
The warning light 1on the instrument cluster will come on.
Pulling the lever towards the steering wheel again, the main beams
are turned off (and the dipped beams on).
FLASHING THE HEADLIGHTS
Pull the lever towards the steering wheel (unstable position)
regardless of the position of the knurled ring.
IMPORTANT Check on the display that stable position is not
engaged.
L0D0069m
L0D0070m
Page 103 of 346

102
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
“FOLLOW ME HOME” DEVICE
This function allows the illumination of the space in front of the car
for a preset time.
Activation
With the ignition key at STOP or removed, pull the stalk towards the
steering wheel and operate it within 2 minutes from when the engine
is turned off.
At each single movement of the stalk, the staying on of the lights is
extended by 30 seconds up to a maximum of 210 seconds; then the
lights are switched off automatically.
Each time the lever is operated, the 3warning light turns on
together with the message on the display (see section “Warning lights
and messages”).
Deactivation
Keep the stalk pulled towards the steering wheel for more than 2
seconds.
L0D0070m
Page 106 of 346

105
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
“Smart washing” function
Pulling the stalk towards the steering wheel (unstable position)
operates the windscreen washer.
Keeping the stalk pulled for over half a second, with just one
movement it is possible to operate the washer jet and the wiper at the
same time.
Releasing the stalk will stop the washer jet immediately whereas the
wiper stops working four strokes later.
A further “cleaning stroke” after five seconds, completes the wiping
operation.
L0D0074m
Page 109 of 346

108
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
REAR WINDOW WASH/WIPE FUNCTION
This device can only work when the ignition key is at MAR.
Turning the knurled ring A from åto
'the rear window wiper is
operated as follows:
❒intermittent operation if the windscreen wiper is off
❒synchronised with the windscreen wiper (but with half stroke
frequency).
With windscreen wiper on and reverse gear engaged, rear window
wiping will be continuous.
Pushing the stalk towards the dashboard (unstable position) will
activate the rear window washer.
Pushing the stalk for over half a second will activated also the rear
window wiper.
Releasing the stalk will activate the smart washing function as
described for the windscreen wiper.
L0D0075m
Page 110 of 346

109
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
CRUISE CONTROL (where provided)
It is a device able to support the driver, with electronic control, which
allows driving at speed over 30 km/h on long and straight dry roads
(e.g.: motorways), at a desired speed, without pressing the accelerator
pedal. Therefore it is not suggested to use this device on extra-urban
roads with traffic. Do not use it in town.
DEVICE ENGAGEMENT
Turn knurled ring A to ON.
The device may only be engaged in the 4th or 5th gear. Travelling
downhill with the device engaged, the car speed may increase more
than the memorised one.
When the device is activated, the warning light
Üon the instrument
cluster turns on together with the message (where provided) on the
multifunction display.
L0D0076m
Page 138 of 346

137
SAFETY
DEVICES
CORRECT
USE OF
THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
To adjust the headlight slant
To adjust the headlight slant operate buttons
andÒlocated on the
dashboard.
The display provides the visual indication of the positions during the
adjustment operation.
Position 0 - one or two people occupying the front seats.
Position 1 - five people.
Position 2 - five people + load in the boot.
Position 3 - driver + maximum permissible load stowed in the boot.
IMPORTANT Check beam aiming every time the load carried
changes.
HEADLIGHT ADJUSTMENT ABROAD
The dipped-beam headlights are adjusted for circulation in the
country in which the vehicle is marketed. In countries with opposite
circulation, to avoid glaring oncoming vehicles, it is necessary to
cover the areas of the headlight as shown below: this is done using
non-transparent sticker tape.
Figures refer to passing from right-hand drive to left-hand drive.
L0D0116m
L0D0118m
L0D0119m