low beam Lancia Musa 2009 Owner handbook (in English)

150
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
IF AN EXTERIOR
LIGHT BURNS OUT
For the type of bulb and power rat-
ing, see “When needing to change a
bulb”.
FRONT LIGHT CLUSTERS
The front light clusters contain side-
lights, dipped beam, main beam and
direction indicator bulbs.
To replace the bulbs in the sidelights,
dipped beam and main beam lights,
remove the protective caps.The bulbs are arranged inside the
light unit fig. 17:as follows:
Cdirection indicators
Dmain beam
Bsidelights
Fdipped beam
After replacing the bulbs, put the
protective caps for the lights changed
back into position and ensure that
they are effectively locked into place.IMPORTANT To access the bulb
holder of the left headlight (direction
of travel) in order to replace it, first
remove the protective cover B-fig. 18
of the fuse box in the engine com-
partment.
fig. 17L0D0398mfig. 18L0D0125m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 150

151
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
DIPPED BEAM HEADLIGHTS
fig. 19-20
To change the bulb, proceed as fol-
lows:
❒remove the protective caps;
❒turn the bulb holder unit Ain an
anticlockwise direction and re-
move it from its seat;
❒disengage the two tabs Bfrom the
retaining device, remove the bulb
Cand replace it;❒remount the bulb holder unit Ain
its seat and turn it in a clockwise
direction;
❒after replacing the bulbs, put the
protective caps back into position;MAIN BEAM LIGHTS fig. 21
To change the bulb, proceed as fol-
lows:
❒remove the protective caps;
❒release the bulb holding clip A;
❒disconnect the electric connector
B;
❒remove the bulb Cand replace it;
❒fit the new bulb, ensuring that the
outline of the metal part coincides
with the grooves on the curve of
the headlight. Then reconnect the
electrical connector Band reattach
the bulb holding clip A;
❒after replacing the bulbs, put the
protective caps back into position.
fig. 20L0D0401mfig. 21L0D0402mfig. 19L0D0400m
135-164 MUSA 1ed GB 10-07-2008 9:38 Pagina 151

188
WARNING
LIGHTS AND
MESSAGES
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
IDENTIFICATION
DATA
Take note of the identification codes.
The identification data stamped on
the plates fig. 1and their respective
positions are as follows:
1- Model plate.
2- Chassis marking
3- Bodywork paint identification
plate
4- Engine marking.MODEL PLATE fig. 2
This plate is applied to the engine
compartment front beam and shows
the following identification data:
B- Homologation number.
C- Vehicle type code.
D- Chassis number.
E- Maximum vehicle weight fully
loaded.
F- Maximum vehicle weight fully
loaded plus trailer.G- Maximum weight on front axle.
H- Maximum vehicle weight on rear
axle.
I- Engine type.
L- Body version code.
M- Spare part code.
N- Smoke opacity index (for diesel
engines).
fig. 1L0D0450mfig. 2L0D0415m
187-205 MUSA 1ed GB 10-07-2008 9:40 Pagina 188