Lancia Voyager 2012 Owner handbook (in English)

FUSES/TIPM
Cavity Cartridge Fuse Mini-Fuse Description
J1 40 Amp Green — Power Folding Seat
J2 30 Amp Pink — Power Liftgate Module
J3 30 Amp Pink — Rear Door Module (RR Door Node)
J4 25 Amp Natural — Driver Door Node
J5 25 Amp Natural — Passenger Door Node
J6 40 Amp Green — Antilock Brakes Pump/Stability Control System
J7 30 Amp Pink — Antilock Brakes Valve/Stability Control System
J8 40 Amp Green — Power Memory Seat (for versions/markets, where provided)
J9 40 Amp Green — Partial Zero Emissions Vehicle Motor/Flex Fuel
J10 30 Amp Pink — Headlamp Wash Relay/Manifold Tuning Valve
J11 30 Amp Pink — Power Sliding Door Module/Anti–Theft Module Relay Lock
Feed
J12 30 Amp Pink Rear Blower Motor/ RAD Fan
J13 60 Amp Yellow — Ignition Off Draw (IOD) – Main
J14 40 Amp Green — Rear Window Defogger
J15 40 Amp Green — Front Blower
J17 40 Amp Green — Starter Solenoid
J18 20 Amp Blue — Powertrain Control Module Trans Range
J19 60 Amp Yellow — Radiator Fan
J20 30 Amp Pink — Front Wiper LO/HI
J21 20 Amp Blue — Front/Rear Washer
J22 25 Amp Natural — Sunroof Module
M1 — 15 Amp Blue Rear Center Brake Lamp/Brake Switch
M2 — 20 Amp Yellow Trailer Lighting/Fog Lamps
M3 — 20 Amp Yellow Front/Rear Axle Locker/Vacuum Pump Motor
M4 — 10 Amp Red Trailer Tow
M5 — 25 Amp Natural Inverter
M6 — 20 Amp Yellow Power Outlet #1 (ACC), Rain Sensor
M7 — 20 Amp Yellow Power Outlet #2 (BATT/ACC SELECT)
M8 — 20 Amp Yellow Front Heated Seat (for versions/markets, where provided)
305

FUSES/TIPM
Cavity Cartridge Fuse Mini-Fuse Description
M9 — 20 Amp Yellow Rear Heated Seat (for versions/markets, where provided)
M10 — 15 Amp Blue Ignition Off Draw — Video System, Satellite Radio, DVD,
Hands-Free Module, Universal Garage Door Opener, Vanity
Lamp, Streaming Video Module
M11 — 10 Amp Red Ignition Off Draw – Climate Control System
M12 — 30 Amp Green Amplifier (AMP)/Radio
M13 — 20 Amp Yellow Ignition Off Draw— Instrument Cluster, SIREN, Clock Mod-
ule, Multi-Function Control Switch/ITM
M14 — 20 Amp Yellow Spare Fuse
M15 — 20 Amp Yellow Rear View Mirror, Instrument Cluster, Multi-Function Con-
trol Switch, Tire Pressure Monitor, Glow Plug Module – Ex-
port Diesel Only, Assy-Shifter (Hall Effect), Acoustic Noise
Cancellation
M16 — 10 Amp Red Airbag Module/Occupant Classification Module
M17 — 15 Amp Blue Left Tail/License/Park Lamp, Running Lamps
M18 — 15 Amp Blue Right Tail/Park/Run Lamp
M19 — 25 Amp Natural Automatic Shutdown #1 and #2
M20 — 15 Amp Blue Instrument Cluster Interior Light, Switch Bank, Steering
Column Module, Switch Steering Wheel
M21 — 20 Amp Yellow Automatic Shutdown #3
M22 — 10 Amp Red Right Horn (HI/LOW)
M23 — 10 Amp Red Left Horn (HI/LOW)
M24 — 25 Amp Natural Rear Wiper
M25 — 20 Amp Yellow Fuel Pump, Diesel Lift Pump – Export Only
M26 — 10 Amp Red Power Mirror Switch, Driver Window Switch
M27 — 10 Amp Red Ignition Switch, Wireless Control Module, Keyless Entry
Module, Steering Column Lock
M28 — 10 Amp Red Powertrain Control Module, Transmission Feed, Transmis-
sion Control Module
306

FUSES/TIPM
Cavity Cartridge Fuse Mini-Fuse Description
M29 — 10 Amp Red Occupant Classification Module
M30 — 15 Amp Blue Rear Wiper Module, Power Folding Mirror, J1962 Diagnostic
Feed
M31 — 20 Amp Yellow Back-Up Lamps
M32 — 10 Amp Red Airbag Module, TT EUROPE
M33 — 10 Amp Red Powertrain Control Module, Transmission Control Module
M34 — 10 Amp Red Park Assist, Heater Climate Control System Module, Head-
lamp Wash, Compass , IR Sensor, Rear Camera, Lamp Door
FT Drv/Pass, Lamp Flashlight, AHLM, Relay Diesel Cabin
Heater, Rad Fan Diesel
M35 — 10 Amp Red Heated Mirrors
M36 — 20 Amp Yellow Power Outlet #3
M37 — 10 Amp Red Antilock Brakes, Stability Control System, Stop Lamp
Switch, Fuel Pump Rly Hi Control
M38 — 25 Amp Natural Door Lock/Unlock Motors, Liftgate Lock/Unlock Motors
The heated mirrors, lower instrument
panel power outlet and removable
floor console, when in the front posi-
tion are fused with self-resetting fuses
that are only serviceable by an autho-
rized dealer. The power seats are
fused by a 30 Amp circuit breaker
located under the driver's seat. The
power windows are fused by a
25 Amp circuit breaker located under
the instrument panel near the steering
column. If you experience temporary or permanent loss of these systems,
see your authorized dealer for service.
VEHICLE STORAGE
If you are leaving your vehicle dor-
mant for more than 21 days, you may
want to take steps to protect your
battery. You may do the following:
 Remove the 20 Amp mini-fuse in
the Totally Integrated Power Mod-
ule (TIPM) labeled Ignition-Off
Draw (IOD).  Or, disconnect the negative cable
from the battery.
 Anytime you store your vehicle, or keep it out of service for two weeks
or more, run the air conditioning
system at idle for about five min-
utes in the fresh air and high blower
setting. This will ensure adequate
system lubrication to minimize the
possibility of compressor damage
when the system is started again.
307

REPLACEMENT BULBS
LIGHT BULBS –
Interior Bulb Number
Center & Rear Dome Lamp . . . 578
Center & Rear Reading
Lamps . . . . . . . . . . . . . . . . . . 578
Front Door Courtesy Lamp . . . 578
Front Header Reading Lamps (for
versions/markets, where pro-
vided) . . . . . . . . . . . . . . . . . . 578
Liftgate Lamp(s) . . . . . . . . . . . 578
Overhead Console Reading
Lamps . . . . . . . . . . . . . . . . PC579
Removable Console Lamp (for
versions/markets, where
provided) . . . . . . . . . . . . . . . . 194
Visor Vanity Lamps . . . . . 6501966
NOTE:
For lighted switches, see your
dealer for replacement instruc-
tions.
All of the interior bulbs are glass
wedge base or glass cartridge types.
Aluminum base bulbs are not ap-
proved and should not be used for
replacement.LIGHT BULBS –
Exterior
Bulb Number
Headlamp . . . . . . . . . . . . . . . H11
Headlamp (HID) (for versions/
markets, where provided) . . . . D1S
Front Turn Signal . . . . . PY27 / 7W
Front Position Lamp . . . . . . . W5W
Front Fog Lamp . . . . . . . . . . . H11
Side Repeater Lamps . . . . . . W5W
Backup Lamp . . . . . . . . . P27 / 7W
Tail/Stop Lamp . . . . . . . . . . . LED
(Serviced at Authorized Dealer)
Rear Turn
Signal Lamps . . . . . . . . PY27 / 7W
Rear Fog Lamps . . . . . . . . . . LED
(Serviced at Authorized Dealer)
Center High-Mounted
Stop Lamp . . . . . . . . . . . . . . LED
(Serviced at Authorized Dealer)
License Plate Lamp . . . . . . . W5W BULB REPLACEMENT
HIGH INTENSITY
DISCHARGE HEADLAMPS
(HID) (for versions/markets,
where provided)
CAUTION!
Where possible, it is advisable to
have bulbs changed at a LANCIA
Dealership. Proper operation and
orientation of the external lights are
essential for driving safety and com-
plying with the law.
The headlamps are a type of high
voltage discharge tube. High voltage
can remain in the circuit even with the
headlamp switch off and the key re-
moved. Because of this, you should
not attempt to service a headlamp
bulb yourself. If a headlamp bulb
fails, take your vehicle to an au-
thorized dealer for service.
308

WARNING!A transient high voltage occurs at the
bulb sockets of High Intensity Dis-
charge (HID) headlamps when the
headlamp switch is turned ON. It may
cause serious electrical shock or elec-
trocution if not serviced properly. See
your authorized dealer for service.NOTE:On vehicles equipped with High In-
tensity Discharge (HID) headlamps,
when the headlamps are turned on,
there is a blue hue to the lamps. This
diminishes and becomes more
white after approximately 10 sec-
onds, as the system charges.QUAD HEADLAMPS (for
versions/markets, where
provided)CAUTION!
Where possible, it is advisable to
have bulbs changed at a LANCIA
Dealership. Proper operation and
orientation of the external lights are
essential for driving safety and com-
plying with the law.1. Raise the hood to access the high or
low beam bulbs at the rear of the
headlamp housing.
2. Release the two tabs on the side of
the connector and remove the connec-
tor from the bulb.
3. Twist the headlamp bulb and pull
the bulb from the headlamp housing.
4. Install the new headlamp bulb and
twist until locked into the headlamp
housing.
CAUTION!
Do not touch the new bulb with your
fingers. Oil contamination will se-
verely shorten bulb life. If the bulb
comes in contact with an oily sur-
face, clean the bulb with rubbing
alcohol.
5. Reconnect the wiring connector to
the bulb.
FRONT TURN SIGNAL AND
SIDE MARKER LAMPS
Access to change the turn signal or
side marker bulb is from the rear of
the headlamp housing. 1. Twist the turn signal or side
marker socket to remove the socket.
2. Pull bulb from the socket.
3. Replace the bulb and reinstall
socket.
SIDE REPEATER LAMPS
The side repeater lamps are located in
both front fenders.
1. Push the side repeater lamp to the
right and release retaining tab on the
left.
2. Pull side repeater lamp out and
disengage bulb socket from lamp.
3. Press, then rotate and pull bulb
from socket.
4. Install bulb to socket.
5. Push the lamp socket into the side
repeater lamp.
Side Repeater Bulb Replacement
309

6. Position metal spring clip in fender
hole notch.
7. Position side repeater lamp to hole
in fender.
8. Push side repeater lamp to com-
press metal spring clip and seat re-
taining tab into fender.
FOG LAMPS
NOTE:
Access to the fog lamp bulb is from
the rear of the fascia. On the left
rear side of the fascia, remove the
push pin and lower the hinged ac-
cess door on the air dam.
1. Remove access cover from under
bumper fascia.
2. Remove bulb from lamp.
3. Disconnect wire harness connec-
tor.
4. Remove the bulb from the connec-
tor socket and install the replacement
bulb.
CAUTION!
Do not touch the new bulb with your
fingers. Oil contamination will se-
verely shorten bulb life. If the bulb
comes in contact with an oily sur-
face, clean the bulb with rubbing
alcohol.
5. Install the bulb and connector as-
sembly into the fog lamp housing.
6. Close and secure the access door
cover under bumper fascia.
REAR TURN SIGNAL AND
BACKUP LAMP
1. Raise the liftgate.
2. Remove the tail lamp assembly by
removing the two screws from the in-
board side. Use a fiber stick or similar
tool to gently pry the light on the
outboard side to disengage the two
ball studs. NOTE:
 If a screwdriver is used, make
sure a soft material is placed be-
tween the vehicle body and tool
so not to scratch the paint.
 The PRY location is best closest to the studs while dislodging
them separately.
3. Twist the socket and remove it
from the lamp assembly.
4. Pull the bulb to remove it from the
socket.
5. Replace the bulb, reinstall the
socket, and reattach the lamp assem-
bly.
310

CENTER HIGH-MOUNTED
STOP LAMP (CHMSL)
The CHMSL uses LED lights are not
serviceable. The CHMSL must be re-
placed as an assembly, see your au-
thorized dealer.LICENSE LAMP
There are two license plate lamps, and
they are located under the tailgate
lamp bar and above the license plate.
1. Remove the two lens assembly
mounting screws.2. Remove the bulb from the socket.
Replace the bulb and reattach the lens
assembly.
FLUID CAPACITIES
Metric
Fuel (Approximate) 76 Liters
Engine Oil with Filter
3.6L Engine 5.6 Liters
2.8L Diesel Engine 6.5 Liters
Cooling System *
3.6L Engine 12.6 Liters
2.8L Diesel Engine 13.8 Liters
* Includes heater and coolant recovery bottle filled to MAX level. Add 2.8 Liters for versions/markets, where provided
with a rear heater.
311

FLUIDS, LUBRICANTS, AND GENUINE PARTS
ENGINEComponentFluids and Lubricants Specs (Genuine Parts)
Engine Coolant* Contact a LANCIA Dealership.
Engine Oil – 3.6L Engine** SAE Grade 5W-30 fully synthetic engine oil that meets FIAT Classification
9.55535, API SN, ILSAC GF-5 (SELENIA K POWER, Contractual Technical
Reference N° F042.F11)
Engine Oil – 2.8L Diesel Engine** SAE Grade 5W-30 fully synthetic engine oil that meets FIAT Classification
9.55535, API SM/CF, ACEA C3 (SELENIA MULTIPOWER C3, Contractual
Technical Reference N° 510.D07)
Spark Plugs – 3.6L Engine RER8ZWYCB4 (Gap 1.1 mm)
Fuel Selection – 3.6L Engine 91 Octane or higher
Fuel Selection – 2.8L Diesel Engine 50 Cetane or higher (Less than 15 ppm Sulfur).
Diesel Fuel Additive – 2.8L Diesel En-
gine Additive for diesel with antifreeze and protective action for diesel engines. (TU-
TELA DIESEL ART, Contractual Technical Reference N° F601.L06. To be
mixed with the diesel fuel: 25 cc per 10 litres)
* Do not top up or mix with fluids
with different specifications.
** Lubricants with ACEA C3 perfor-
mance as a minimum may be used for
Diesel engines in an emergency, where no original products are available. In
such event, the engine may not pro-
vide optimal performance. We recom-
mend having the lubricant replaced
with one of the recommended lubri-
cants at the Lancia Service Networkas soon as possible. Using products
with specifications lower than ILSAC
GF-5 for gasoline engines or lower
than ACEA C3 for Diesel engines may
cause engine damage not covered by
warranty.
312

CHASSISComponentFluids and Lubricants Specs (Genuine Parts)
Automatic Transmission Totally synthetic lubricant that meets FIAT Classification 9.55550-AV4 (TU-
TELA TRANSMISSION FORCE4, Contractual Technical Reference N°
F108.F11)
Brake/Clutch Master Cylinder Synthetic fluid that meets FIAT Classification 9.55597, FMVSS n° 116, DOT 4,
ISO 4925, SAE J-1704 (TUTELA TOP 4, Contractual Technical Reference N°
F001.A93)
Power Steering Reservoir Totally synthetic lubricant that meets FIAT Classification 9.55550-AV4 (TU-
TELA TRANSMISSION FORCE4, Contractual Technical Reference N°
F108.F11)
Windshield/Rear Window Washer
Fluid Mixture of alcohol, water and surfactants that meets FIAT Classification
9.55522, CUNA NC 956-11 (TUTELA PROFESSIONAL SC35, Contractual
Technical Reference N° F201.D02)
313

ARRANGEMENTS FOR DEALING
WITH THE VEHICLE AT THE
END OF ITS LIFE
LANCIA has been committed for
many years to safeguarding the envi-
ronment through the constant im-
provement of its production processes
and manufacturing products that are
increasingly “eco-compatible”.
To give customers the best possible
service in terms of respecting environ-
mental laws and in response to Euro-
pean Directive 2000/53/EC govern-
ing vehicles at the end of their life,
LANCIA is offering its customers the
opportunity of handing over their ve-
hicle* at the end of its life without
incurring any additional costs.
The European Directive sets out that
when the vehicle is handed over thelast keeper or owner should not incur
any expenses as a result of it having a
zero or negative market value.
In all European Union countries, until
1st January 2007, only vehicles regis-
tered after 1st July 2002 were col-
lected free of charge, while since 2007
collection has been free of charge irre-
spective of the year of registration as
long as the vehicle contains its basic
components (in particular, the engine
and bodywork) and has no additional
waste.
To hand your vehicle over at the end
of its life without extra cost, go to one
of our Dealerships or LANCIA-
authorized collection and scrapping
centres.
These centres have been carefully
chosen to offer high quality service forthe collection, treatment and recy-
cling of unused vehicles with respect
to the environment.
You can find further information on
these collection and scrapping centres
either from a LANCIA or LANCIA
Commercial Vehicle Dealership or by
calling the freephone number 00800
526242 00 or by going on the
LANCIA website.
(*) Vehicle for transporting passen-
gers with a maximum of nine seats
and a total permitted weight of 3.5 t
314