engine LAND ROVER DEFENDER 1996 Owners Manual

33CLUTCH
2
REPAIR MASTER CYLINDER
Service repair no - 33.20.01/03
NOTE: All hose and pipe connections and
joints should be tightened to
15 Nm (11
lbf/ft).
Remove
1.Drain hydraulic fluid from system.
2.Disconnect fluid pipe at master cylinder. Plug
master cylinder fluid port and seal end of
hydraulic pipe to prevent ingress of dirt.
3.On RH drive vehicles, unclip air cleaner retaining
straps, disconnect bottom hose, and move
assembly aside.
4.From inside vehicle, remove fibre board closing
panel above pedals.
5.Remove 6 bolts securing pedal bracket to
bulkhead.
6.Remove screw securing speedometer cable
retaining bracket to top of pedal bracket.
7.Move pipework and cables aside and lift out
pedal bracket, complete with master cylinder,
turn through 90°to ensure pedal clears aperture
in bulkhead.8.Remove 6 screws and detach pedal box top
cover and gasket.
9.Remove nut and washer securing master
cylinder push rod to clutch pedal trunnion.
10.Remove 2 nuts and bolts and withdraw master
cylinder from pedal bracket.
Refit
11.Fit master cylinder to pedal bracket, engaging
cylinder push rod through pedal trunnion.
12.Secure push rod to pedal trunnion.
13.Apply sealant to mating surfaces and fit pedal
bracket to engine bulkhead.
14.Connect fluid pipe to master cylinder.
15.Bleed clutch hydraulic system
See Bleed
hydraulic system
.
16.Check and adjust clutch pedal and master
cylinder setting
See Adjustment, Clutch pedal
and master cylinder setting
.
17.Fit top cover and gasket to pedal bracket.
18.On RH drive vehicles, refit air cleaner.

MANUAL GEARBOX
1
DESCRIPTION AND OPERATION R380 GEARBOX
Description
The all synchromesh five speed manual gearbox unit,
is married to a two speed transfer gearbox.
All the gears, including reverse, run on needle roller
bearings and the main, layshaft and primary shafts
are supported by tapered roller bearings.The whole of the geartrain is lubricated through
drillings in the shafts, supplied by a low pressure
pump driven from the rear of the layshaft. The gear
change has a single rail selector and spool type
interlock. The main and transfer gearboxes ventilate
through nylon pipes, which terminate high up in the
engine compartment to prevent water entry when the
vehicle is operating in adverse conditions.
R380 Gearbox Components
1.Mainshaft 1st gear
2.Mainshaft 2nd gear
3.Mainshaft 3rd gear
4.Primary input shaft/4th gear
5.Mainshaft 5th gear
6.Layshaft
7.Mainshaft
8.Lubrication pump
9.Oil filter10.Ventilation pipe
11.Single rail gear shift
12.1st/2nd synchromesh
13.Oil seals
14.3rd/4th synchromesh
15.5th/reverse gear synchromesh
16.Selective spacers (mainshaft/layshaft end float)
17.Selective spacer (5th gear/reverse hub)

MANUAL GEARBOX
1
FAULT DIAGNOSIS R380 GEARBOX
Symptom - Gear jumps out of engagement (any
forward gear)
1.Check condition and security of transmission
and engine mountings.
2.Check in situ, gear lever and selector
adjustments
See Adjustment, Gear change
lever bias spring - adjust
andSee
Adjustment, Fifth gear stop screw adjust
.
3.In situ, remove gearshift and check selector rail
yoke security.
Also check selector detent spring tension and
both spool retainers.
Suspect internal fault, see Overhaul Manual.
4.Check action/operation of main selector rail and
forks.
5.Check condition of synchromesh and gear dog
teeth.
6.Check main and layshaft end floats bearings and
adjustments.
7.Check condition of all gearbox components,
ensure clearances and adjustments are correct
on reassembly.
Symptom - Reverse gear only jumps out of
engagment
1.Check condition and security of transmission
and engine mountings.
2.Check in situ, gear lever and selector
adjustments
See Adjustment, Gear change
lever bias spring adjust
andSee Adjustment,
Fifth gear stop screw adjust
.
3.In situ, remove gearshift and check selector rail
yoke security.
Also check selector detent spring tension and
both spool retainers.
Suspect internal fault, see Overhaul Manual.
4.Check action/operation of main selector rail and
reverse lever.
5.Check condition of reverse gear, angled
bearings and shaft.
6.Check condition of all gearbox components,
ensure clearances and adjustments are correct
on reassembly.Symptom - Excessive force required to engage or
change gear, vehicle stationary or moving.
1.Check lubricant specification and level, if low do
not top up at this stage.
2.In situ, lubricate gear mechanism, and check
selector adjustments
See Adjustment, Gear
change lever bias spring - adjust
andSee
Adjustment, Fifth gear stop screw adjust
.
3.In situ, remove gearshift and check selector rail
is free and that the yoke is secure. Also check
selector detent spring tension and both spool
retainers.
4.Drain lubricant and check for contamination or
metal particles.
Suspect worn synchromesh unit or baulk rings
on affected gears, see Overhaul Manual.
Symptom - Noisy gear engagement, vehicle
stationary
See CLUTCH, Fault diagnosis, Clutch
Noise - Mechanical Faults
.
Symptom - Noisy gear selection, vehicle moving.
1.Confirm that clutch operation is satisfactory.
2.Establish which gear/gears is causing noise.
3.Check lubricant specification and level, if low do
not top up at this stage.
4.Drain lubricant and check for contamination or
metal particles.
Suspect worn synchromesh, see Overhaul
Manual.
5.Check condition of synchromesh unit, springs
and cones for distortion and wear. Also check
dog teeth for damage and cone mating surface
on gear for signs of overheating.
6.Check condition of all gearbox components,
ensure clearances and adjustments are correct
on reassembly.
Symptom - Noise from gearbox in neutral, which
changes tone or becomes worse when clutch is
depressed,
See CLUTCH, Fault diagnosis, Clutch
Noise - Mechanical Faults
.
Symptom - Noise from gearbox in neutral, which
disappears when clutch is depressed.
1.Check lubricant specification and level, if low do
not top up at this stage.
2.Drain lubricant and check for contamination or
metal particles.
Suspect worn bearings on layshaft, primary shaft
or front of main shaft, see Overhaul Manual.

37MANUAL GEARBOX
2
REPAIR
10.Remove 3 trim studs and lift up handbrake
gaiter.
11.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever. Ensure
handbrake is off.
12.Drain cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
13.Remove viscous fan unit
See COOLING
SYSTEM, Repair, Viscous coupling and fan
.
14.Slacken retaining clip and disconnect radiator
top hose at thermostat housing.
15.Slacken retaining clip and disconnect intake
hose at induction manifold. If EGR system is
fitted, slacken 2 retaining clips and disconnect
intake hose at intercooler.
16.Slacken retaining clip and disconnect hose at
turbocharger.
17.Remove bolt securing transmission breather
pipe clip to rear of engine.
18.Release breather pipes.
19.Release ties securing gearbox harness to
breather pipes.
20.Raise vehicle on ramp.
21.Position a suitable container under transmission
and drain main gearbox and transfer box
See
MAINTENANCE , Under vehicle maintenance
.
22.Mark front propeller shaft drive flange and
transfer box output flange for reassembly.
23.Remove 4 nuts and disconnect propeller shaft
from transfer box.

37MANUAL GEARBOX
4
REPAIR
37.Pull handbrake cable through heel board and tie
aside.
38.Remove retaining nut, release clamp, and
disconnect speedometer cable from transfer box.
39.Release speedometer cable from retaining clip
on transfer box.
40.Remove retaining nut and release battery earth
strap from transfer box.
41.Secure manufactured cradleLRT-99-007to a
suitable hydraulic hoist.
42.Raise hoist and secure to gearbox with 3 bolts in
location provided.
43.Lower hoist sufficiently to allow transfer lever to
clear transmission tunnel aperture.
44.Disconnect differential lock switch and reverse
light connectors.
45.Remove bolt and release earth leads from RH
side of transfer box.
46.Support engine under sump with a jack.
47.Remove 14 bell housing to engine fixings.
48.Withdraw transmission whilst ensuring all
connections to engine and chassis are released.
49.Lower hoist and remove gearbox assembly.

MANUAL GEARBOX
5
REPAIR Separating transfer gearbox from main gearbox
50.Remove transmission assembly from hoist
cradle and position safely on a bench.
51.Remove breather pipes. Discard pipe union
sealing washers.
52.Remove 'Nyloc' nut, and remove bolt, securing
lever to high/low shaft.
53.Collect spacer washer.
54.Remove 2 clips and remove differential lock
lever link.
55.Remove lower locknut from high/low operating
rod.
56.Place a sling round transfer box and attach to
hoist.
57.Remove nut and 4 bolts securing transfer
gearbox to extension housing.
58.Withdraw transfer gearbox.
Assembling transfer gearbox to main gearbox
59.Clean extension housing and transfer gearbox
mating faces.
60.Ensuring loose upper dowel is fitted, hoist
transfer gearbox into position.
61.Secure transfer box to extension housing.
Tighten fixings to
40 Nm (30 lbf/ft).
62.Connect high/low operating rod, fit and tighten
locknut.
63.Fit link to differential lock lever and secure with 2
clips
64.Align lever to high/low shaft, position washer, fit
bolt and new Nyloc nut. Tighten to
2 Nm (1.5
lbf/ft).
65.Position breather pipes, secure pipe unions
using new sealing washers. Tighten unions to
15
Nm (11 lbf/ft).
Fitting transfer gearbox and main gearbox
assembly
66.Position transmission assembly to hoist cradle.
67.Clean bell housing and engine mating faces.
Apply sealant to both mating faces.
68.Temporarily fit gear lever and select any gear in
main gearbox to facilitate entry of gearbox input
shaft. Engage low range.
69.Position and raise hoist, fit transmission to
engine whilst keeping harness and pipes clear to
prevent trapping.
70.Secure transmission to engine. Tighten fixings to
45 Nm (33 lbf/ft).
71.Secure earth leads to RH side of transfer box.
72.Connect reverse lamp switch connectors and
differential lock switch connectors.
73.Secure breather pipes to harness with clips.
74.Remove support from engine sump.
75.Position temporary support under transmission.
76.Secure LH and RH mounting brackets to
gearbox. Tighten fixings to
55 Nm (41 lbf/ft).
77.With assistance and using a body jack between
chassis longitudinals, jack chassis sufficiently to
enable fitment of crossmember.

37MANUAL GEARBOX
6
REPAIRREV: 05/99 78.Position crossmember and locate over fixing
studs of LH and RH gearbox mounting rubbers.
79.Align crossmember and secure to chassis with 4
nuts and bolts on each side.
NOTE: Fit battery earth strap retaining clip
to LH top bolt.
80.Fit intermediate silencer.
See MANIFOLD AND
EXHAUST SYSTEM, Repair, Intermediate
pipe - 90
orSee MANIFOLD AND EXHAUST
SYSTEM, Repair, Intermediate pipe - 110/130
.
81.Fit front pipe to exhaust manifold
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust front pipe
.
82.Fit rear propeller shaft to transmission brake
drum. Tighten nuts to
47 Nm (33 lbf/ft).
83.Remove 3 bolts securing support cradle to
transmission and remove hoist.
84.Reconnect battery earth strap to transfer box
fixing.
85.Connect speedometer cable to transfer box and
secure with retaining clip.
86.Coat both sides of clutch slave clinder backing
plate with Hylomar P232M waterproof sealant.
87.Locate backing plate on slave cylinder.
88.Fit slave cylinder to bell housing, engaging
push-rod through centre of dust cover, and with
bleed screw uppermost. Tighten bolts to
25 Nm
(18 lbf/ft).
89.Fit front propeller shaft to transfer box. Tighten
nuts to
47 Nm (33 lbf/ft).
90.Refill main gearbox and transfer boxSee
MAINTENANCE , Under vehicle maintenance
.
91.Feed transmission brake cable through heel
board and ensure grommet is correctly located.
NOTE: Apply a soap solution to aid fitment
of cable.
92.Lower vehicle on ramp.
93.Fit ties to secure gearbox harness to
transmission breather pipes.
94.Fit breather pipe retaining clip to rear of engine.
95.Reconnect charge air hose at turbocharger.
96.Reconnect intake hose at induction manifold. If
EGR system is fitted, reconnect intake hose at
intercooler.
97.Reconnect radiator top hose at thermostat
housing.
98.Fit viscous fan unit
See COOLING SYSTEM,
Repair, Viscous coupling and fan
.
99.Reconnect battery.100.Refill cooling system
See COOLING SYSTEM,
Adjustment, Drain and refill cooling system
.
101.Connect cable clevis to handbrake lever and fit
handbrake gaiter.
102.Locate insulation pad over gear levers and fit to
tunnel cover.
103.Fit gear lever with gaiter to lower lever spline
and secure with retaining nut.
104.Fit gear lever cover.
105.Fit gear lever and transfer box lever knobs.
106.Fit gearbox cover carpet.
107.Check operation of handbrake and adjust as
necessary
See MAINTENANCE , Under
vehicle maintenance
.

41TRANSFER GEARBOX
2
FAULT DIAGNOSIS OIL LEAKS
Verify that oil leak is from transfer box and not main
gearbox before proceeding with checks.
Prior to road test
1.Check oil level in transfer box is correct.
2.Check tightness of level and drain plugs.
3.Check breather system for blockage. To validate
system pipe must be removed, inspected,
rectified as necessary and refitted.
4.Remove all traces of oil from exterior of transfer
box.
Take vehicle for short road test.
5.Identify source of leaks and rectify as follows.
Front or rear output seal leaking:-
1.Drain oil and remove leaking output flange.
2.Inspect seal track on flange for surface damage.
If damaged renew component.
3.Remove and discard oil seal.
4.Inspect seal locating bore and remove any sharp
edges which may damage new oil seal.
5.Fit new seal.
6.Fit output flange and all other parts.
7.Add oil to correct level into gearbox
See
SECTION 10, Maintenance, Under vehicle
maintenance
.
Cover plate sealant leaking.
1.Drain oil and remove leaking cover plate.
2.Remove all traces of joint sealant from both joint
faces.
3.Degrease all components and apply a thin film of
Hylomar sealant, to both joint faces.
4.Apply thread sealant to bolts which come into
contact with gearbox oil.
5.Refit cover plate.
CAUTION: Care must be taken not to
overtighten fixings.Leak between main and transfer gearboxes.
1.Site vehicle onto a ramp .
2.Select neutral in transfer box and select 4th gear
in main gearbox.
3.Run engine at 2000 rpm with clutch/drive
engaged.
4.Observe joint between main and transfer boxes.
5.If oil leak is found establish if it is gear oil.
6.If so, leak is originating from transfer box.
7.Check two inner (main/transfer) bolts are oil
tight, as these holes are tapped into main
transfer case.
8.Remove transfer box to inspect mainshaft collar
seal track condition, and front face of transfer
case for porosity
See Repair, Transfer
gearbox
.
9.If these areas require servicing, transfer gearbox
input seal must also be renewed.
CAUTION: Avoid damaging new seal lip
and ensure seal is fitted flush with
machined face. Also ensure new seal is
not damaged when refitting transfer gearbox.
10.If red ATF type oil is seen leaking during
workshop test, investigate main gearbox for
cause of leak.
Detent plug or electrical switch leaks.
1.Detent plugs and electrical switches do not
usually leak. It must be noted that they fit into
open tapped holes in transfer case and therefore
should be considered when looking for source of
leak.

STEERING
1
DESCRIPTION AND OPERATION DESCRIPTION
The steering system incorporates a compression joint
in the lower shaft and is designed to collapse on
impact. The mis-alignment of the upper steering
column with the steering box and the inclusion of two
universal joints, is also designed to prevent the
column moving toward the driver under frontal impact.
The steering box is located behind the first chassis
cross member and is connected to the road wheel
swivel housing by a drag link and track rod. A
hydraulic damper absorbs shocks in the steering,
caused by road wheel deflections when operating on
rough terrain.Power steering system
The power steering system comprises a hydraulic
pump which is belt driven from the engine and
supplied with fluid from a reservoir that also acts as a
cooler.
The steering box houses a self neutralizing rotary
valve which is part of the worm/valve assy and an
hydraulic piston/rack to assist the mechanical
operation. The rotary valve which is operated by
movement of the steering wheel, directs fluid pressure
to the appropriate side of the hydraulic piston/rack to
provide assistance.
Power steering system
1.Hydraulic pump
2.Fluid reservoir
3.Steering box
4.Upper column5.Universal joints
6.Lower shaft
7.Compression joint
8.Drag link

STEERING
5
DESCRIPTION AND OPERATION Pump and regulator valve operation
The pump which is belt driven from the engine is an
eccentric roller type and also houses the pressure
regulator and flow control valve. The pressure is
controlled by a spring loaded ball valve (3) which is
housed inside the flow control valve piston (4).
No demand for assistance High flow through box -
Low pressure
With no demand for assistance the rotary valve in the
steering box acts as a pressure relief valve, allowing
fluid (A) to flow freely through the steering box and
back to the reservoir and pump inlet (B).
No demand for assistance
1.Reservoir
2.Pump
3.Pressure control ball valve and spring
4.Flow control valve and spring
5.Press fit plug (ball bearing)
6.Restrictor
The ball plug (5) is pressed into the valve (4)
during manufacture and determines the opening
pressure of pressure relief valve (3).No flow, through box - High pressure
When the steering is turned, the rotary valve
effectively stops all fluid flow through the steering box,
thus causing an increase in pressure (A). This
increase in pressure is felt in the flow control valve
spring chamber where, at a pre-determined pressure
the relief valve (3) will open and allow the pressure to
escape. The fall in pressure in the flow control spring
chamber, allows the flow control valve to move to the
right, which in turn allows pump output (A) to escape
directly into the pump inlet (B).
Assistance demanded
As soon as the steering wheel is released after
making a turn, the system reverts to the condition
seen in J6292 and the road wheels are returned to the
straight ahead position by the mechanical steering
geometry.
In the event of any hydraulic failure, steering control,
though heavy, will be maintained through the
mechanical components in the steering box.