lock LAND ROVER DEFENDER 1996 Service Manual

19FUEL SYSTEM
14
REPAIR TURBOCHARGER INLET HOSE
Service repair no - 19.42.11
Remove
1.Disconnect battery.
2.Slacken retaining clip and disconnect intake
hose from turbocharger.
3.Slacken retaining clip and disconnect hose from
air cleaner.
4.If fitted, disconnect EGR modulator valve
vacuum spill pipe from inlet hose.
5.Slacken retaining clip and disconnect breather
valve hose from inlet hose.
6.Remove inlet hose.
Refit
7.Fit inlet hose to air cleaner.
8.Fit cyclone breather hose to inlet hose.
9.If applicable, fit vacuum spill pipe to inlet hose.
10.Fit inlet hose to turbocharger.
11.Reconnect battery.TURBOCHARGER OIL FEED PIPE
Service repair no - 19.42.14
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Remove banjo bolt securing oil feed pipe to
turbocharger and discard 2 joint sealing
washers.
4.Unscrew union and remove feed pipe from
cylinder block.
5.Plug connections to prevent ingress of dirt.
Refit
6.Using new joint washer, fit oil feed pipe to
cylinder block. Tighten union connector to
25
Nm (18 lbf/ft).
7.Fit a new joint washer to both sides of banjo and
secure feed pipe to turbocharger. Tighten banjo
bolt to
20 Nm (15 lbf/ft).
8.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
9.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
10.Reconnect battery.

FUEL SYSTEM
15
REPAIR TURBOCHARGER OIL DRAIN PIPE
Service repair no - 19.42.12
Remove
1.Disconnect battery.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
front pipe
3.Unscrew union and disconnect oil drain pipe
from cylinder block.
4.Remove 2 bolts securing oil drain pipe to
turbocharger.
5.Remove drain pipe and discard gasket.
6.Plug connections to prevent ingress of dirt.
Refit
7.Ensure mating surfaces of oil pipe, turbocharger
and engine block are clean.
8.Using new gasket, fit oil drain pipe to
turbocharger. Tighten bolts to
25 Nm (18 lbf/ft).
9.Fit drain pipe to cylinder block and tighten union
connector to
38 Nm (28 lbf/ft).
10.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Exhaust front
pipe
11.Check/top-up engine oil level.See SECTION
10, Maintenance, Under bonnet maintenance
12.Reconnect battery.

COOLING SYSTEM
3
REPAIR WATER PUMP
Service repair no - 26.50.01
Remove
1.Disconnect battery.
2.Drain cooling system.
See Adjustment, Drain
and refill cooling system
3.Remove radiator top hose.
4.Remove intercooler top hose.
5.Slacken water pump and power steering pump
pulley retaining bolts.
6.Remove drive belt.
See ELECTRICAL, Repair,
Auxiliary drive belt
7.Unscrew flange nut and remove belt tensioner.
8.Remove oil filler cap and remove rocker cover
insulation.
9.Slacken retaining clip and disconnect hose at
heater rail.
10.Unscrew 3 bolts and remove water pump pulley.
11.Unscrew 3 bolts and remove power steering
pump pulley.
12.Remove 8 bolts securing water pump, noting
location of 3 through bolts into cylinder block.
13.Withdraw pump and gasket from auxiliary
mounting bracket.
14.Clean all gasket material from mating faces.
Refit
15.Using new gasket, fit water pump to mounting
bracket. Tighten bolts to
25 Nm (18 lbf/ft).
16.Fit power steering pump pulley.
17.Fit water pump pulley. Tighten bolts of both
pulleys to
25 Nm (18 lbf/ft).
18.Fit drive belt.See ELECTRICAL, Repair,
Auxiliary drive belt
19.Fit hose at heater rail.
20.Fit rocker cover insulation and oil filler cap.
21.Fit drive belt tensioner. Tighten retaining nut to
45 Nm (33 lbf/ft).
22.Fit intercooler top hose.
23.Fit radiator top hose.
24.Refill cooling system.
See Adjustment, Drain
and refill cooling system
25.Reconnect battery.

26COOLING SYSTEM
4
REPAIRREV: 05/99 AUXILIARY MOUNTING BRACKET AND GASKET
Service repair no - 26.50.04
Remove
1.Disconnect battery.
2.Drain cooling system
See Adjustment, Drain
and refill cooling system
.
3.Remove radiator top hose.
4.Remove intercooler top hose.
5.Remove viscous fan unit.
See Viscous
coupling and fan
6.Remove fan cowl.See Fan cowl
7.Slacken power steering pump pulley retaining
bolts.
8.Remove drive belt.
See ELECTRICAL, Repair,
Auxiliary Drive belt
9.Unscrew 3 bolts and remove power steering
pump pulley.
10.Remove 4 bolts securing power steering pump
mounting bracket.
11.Lower pump and bracket. Do not disconnect fluid
pipes.
12.Remove generator.
See ELECTRICAL, Repair,
Generator
13.Unscrew retaining nut and remove drive belt
tensioner.
14.Release hose clip from bracket above water
pump.15.Disconnect bottom hose/heater return hose at
water pump and heater rail.
16.Disconnect by-pass hose from water pump and
thermostat housing.
17.Remove 5 bolts (one with nut) and single
retaining nut, securing auxiliary mounting
bracket to cylinder block.
18.Withdraw mounting bracket, complete with water
pump.
19.Remove gasket and clean mating faces.
Refit
20.Using 2 slave studs, fit new gasket.
NOTE: All fixing bolts and nuts should be
tightened to
25 Nm (18 lbf/ft)unless
otherwise stated.
21.Locate mounting bracket, complete with water
pump on slave studs and secure with 4 other
fixings.
22.Remove slave studs and fit remaining bolts/nuts.
23.Fit by-pass hose to thermostat housing and
water pump.
24.Fit bottom hose/heater return hose to water
pump and heater rail.
25.Fit heater hose clip to mounting bracket.
26.Fit drive belt tensioner. Tighten nut to
45 Nm (33
lbf/ft).
27.Fit generator.See ELECTRICAL, Repair,
Generator
Do not fit drive belt at this stage.

30MANIFOLD AND EXHAUST SYSTEM
2
REPAIR Refit
11.Fit new gasket over manifold studs.
12.Loosely fit induction manifold lower nuts to
studs.
13.Fit exhaust manifold and secure with central
upper and lower nuts.
14.Locate heater rail to its correct position and
secure with outer exhaust manifold nuts.
15.Tighten all exhaust manifold nuts to
45 Nm (33
lbf/ft).
16.Tighten exhaust front pipe to intermediate
silencer nuts to
50 Nm (37 lbf/ft).
17.Fit turbocharger outlet pipe.
18.Fit induction manifold
See Induction manifold
.EXHAUST MANIFOLD/TURBOCHARGER
ASSEMBLY
Service repair no - 30.15.10
Remove
1.Remove induction manifold
See Induction
manifold
.
2.Disconnect turbocharger inlet hose.
3.Disconnect boost pressure pipe at turbocharger.
4.Remove intercooler bottom hose.
5.Place suitable container under engine and
disconnect turbocharger oil feed and return
pipes at cylinder block.
6.Remove 3 nuts securing exhaust front pipe to
manifold flange.
7.Remove 7 nuts and lift exhaust manifold and
turbocharger assembly from cylinder head.
8.Discard manifold gasket.
Refit
9.Fit new manifold gasket.
10.Position exhaust manifold assembly onto
location studs and secure to cylinder head.
Tighten nuts to
45 Nm (33 lbf/ft).
11.Secure exhaust front pipe to manifold flange.
Tighten fixings to
50 Nm (37 lbf/ft).
12.Reconnect turbocharger oil feed and return
pipes at cylinder block.
13.Fit intercooler bottom hose.
14.Fit boost pressure pipe at turbocharger.
15.Fit turbocharger inlet hose.
16.Fit induction manifold
See Induction manifold
.

CLUTCH
1
ADJUSTMENT CLUTCH PEDAL AND MASTER CYLINDER
SETTING
1.Remove 6 screws and detach pedal box top
cover and gasket.
2.Slacken both locknuts on master cylinder
push-rod.
3.Check distance from lower edge of clutch pedal
to floor. Correct measurement is 140 mm (5.50
in) without floor mat.
4.Adjust pedal stop as necessary to obtain correct
setting.
5.Adjust master cylinder push rod to obtain
approximately 1,5 mm (1/16 in) free play
between push-rod and master cylinder piston.
6.Tighten push-rod locknuts.7.Check operation of clutch pedal and ensure that
there is a minimum of 6 mm (0.25 in) of free play
before pressure is felt. If necessary, readust
master cylinder push-rod.
8.Fit pedal box gasket and top cover.

CLUTCH
1
OVERHAUL MASTER CYLINDER - OVERHAUL
Service repair no - 33.20.07
Dismantle
1.Remove master cylinder from vehicle
See
Repair, Master cylinder
.
2.Remove circlip.
3.Withdraw push-rod and retaining washer.
4.Withdraw the piston assembly. If necessary,
apply a low air pressure to outlet port to expel
piston.
5.Prise locking prong of spring retainer clear of
piston shoulder and withdraw piston.
6.Withdraw piston seal.
7.Compress spring and position valve stem to
align with larger hole in spring retainer.
8.Withdraw spring and retainer.
9.Withdraw valve spacer and spring washer from
valve stem.
10.Remove valve seal.
Inspection
11.Clean all components in new hydraulic fluid and
allow to dry.
12.Examine cylinder bore and piston, ensure that
they are smooth to touch with no corrosion,
score marks or ridges. If there is any doubt, fit
new components.
13.The seals should be renewed with seals from
master cylinder overhaul kit.
Assemble
14.Smear seals with suitable rubber grease and
remaining internal items with new hydraulic fluid.
15.Fit valve seal, flat side first, on end of valve
stem.
16.Place bowed washer, domed side first, over
small end of valve stem, see J6281.
17.Fit spacer to valve, legs first.

33CLUTCH
2
OVERHAUL
18.Place coil spring over valve stem.
19.Insert retainer into spring.
20.Compress spring and engage valve stem in
keyhole slot in retainer.
21.Fit seal, large diameter last, to piston.
22.Insert piston into spring retainer and engage
locking prong.
23.Smear piston with suitable rubber grease and
insert assembly, valve end first, into cylinder.
24.Fit push-rod, retaining washer and circlip.
25.Fit clutch master cylinder to vehicle
See Repair,
Master cylinder
.SLAVE CYLINDER - OVERHAUL
Service repair no - 33.35.07
Dismantle
1.Remove slave cylinder
See Repair, Slave
cylinder
.
2.Withdraw dust cover.
3.Expel piston assembly, applying low pressure air
to fluid inlet.
4.Withdraw spring.
5.Remove seal from piston.
6.Remove bleed valve.
Inspection
7.Clean all components with new hydraulic fluid
fluid and allow to dry.
8.Examine cylinder bore and piston, ensure that
they are smooth to touch with no corrosion,
score marks or ridges. If there is any doubt, fit
new components.
9.Renew seal and dust cover from slave cylinder
overhaul kit.

MANUAL GEARBOX
1
DESCRIPTION AND OPERATION R380 GEARBOX
Description
The all synchromesh five speed manual gearbox unit,
is married to a two speed transfer gearbox.
All the gears, including reverse, run on needle roller
bearings and the main, layshaft and primary shafts
are supported by tapered roller bearings.The whole of the geartrain is lubricated through
drillings in the shafts, supplied by a low pressure
pump driven from the rear of the layshaft. The gear
change has a single rail selector and spool type
interlock. The main and transfer gearboxes ventilate
through nylon pipes, which terminate high up in the
engine compartment to prevent water entry when the
vehicle is operating in adverse conditions.
R380 Gearbox Components
1.Mainshaft 1st gear
2.Mainshaft 2nd gear
3.Mainshaft 3rd gear
4.Primary input shaft/4th gear
5.Mainshaft 5th gear
6.Layshaft
7.Mainshaft
8.Lubrication pump
9.Oil filter10.Ventilation pipe
11.Single rail gear shift
12.1st/2nd synchromesh
13.Oil seals
14.3rd/4th synchromesh
15.5th/reverse gear synchromesh
16.Selective spacers (mainshaft/layshaft end float)
17.Selective spacer (5th gear/reverse hub)

MANUAL GEARBOX
1
ADJUSTMENT GEAR CHANGE LEVER BIAS SPRING - ADJUST
Service repair no - 37.16.26
1.Remove gear lever and transfer box lever knobs.
2.Remove gear lever cover.
3.Remove nut and washer securing gear lever.
4.Mark gear lever spline setting, remove lever and
gaiter from lower lever.
5.Remove insulation pad from tunnel aperture.
6.Fit gear lever and select 3rd or 4th gear.
7.Slacken adjustment screw locknuts.
8.Adjust screws until both legs of bias springs are
approximately 0.5mm clear of gear lever cross
pin.
9.Apply a slight load to gear lever in a LH direction
and adjust RH screw downward until RH spring
leg just makes contact with cross pin.
10.Repeat procedure for LH adjustment screw.
11.Lower both adjustment screws equal amounts
until radial play is eliminated.
12.Tighten locknuts.
13.Return gear lever to neutral position and rock
across gate several times. The gear lever should
return to 3rd and 4th gate.
14.Remove gear lever.
15.Fit insulation pad.
16.Locate gaiter over lower lever and bias springs.
17.Fit gear lever to lower lever spline, secure with
new nyloc nut and tighten to
25 Nm (18 lbf/ft).
18.Fit gear lever cover.
19.Fit gear lever and transfer box lever knobs.