lock LAND ROVER DEFENDER 1996 Manual PDF

REAR AXLE AND FINAL DRIVE
7
OVERHAUL
83.Position dial gauge centrally on pinion end face
with stylus registering on lowest point on one
differential bearing bore. Note dial gauge
deviation from zeroed setting.
84.Repeat on other bearing bore. Add together
readings, then halve sum to obtain mean
reading. Note whether stylus has moved up or
down from zeroed setting.
Example 1
Reading obtained LH side.............. + 0.1524mm
Reading obtained RH side............. - 0.0762mm
Add + 0.1524mm - 0.0762mm = + 0.0762mm
Divide by 2 (0.0762 divided by 2)= 0.0381mm
Therefore subtract 0.0381mm from shim thickness
behind pinion inner bearing track.
Example 2
Reading obtained LH side............. + 0.1524mm
Reading obtained RH side............ - 0.2032mm
Add + 0.1524mm - 0.2032mm = + 0.0508mm
Divide by 2 (0.0508 divided by 2)= 0.0254mm
Therefore add 0.0254mm from shim thickness behind
pinion inner bearing track.
85.Where stylus has moved down (85a), amount is
equivalent to thickness of shims that must be
removed from under pinion inner cup to bring
pinion down to nominal position. Where stylus
has moved up (85b), amount is equivalent to
additional thickness of shims required to bring
pinion up to nominal position.
Illustration A. Using setting gauge18G191P.
Illustration B. Using universal setting block
LRT-54-503. This setting block has 3 setting heights.
Ensure that height marked 30.93 mm is used for this
differential.

REAR AXLE AND FINAL DRIVE
9
OVERHAUL Differential backlash checks
96.Pick up differential unit as left after instruction
52.
97.Fit differential unit and lever unit away from drive
pinion until opposite bearing cup is seated
against housing. Do not tilt unit.
98.Install a dial gauge on casing with its stylus
resting on back face of crown wheel. Zero the
gauge.
99.Lever differential unit to engage crown wheel
teeth in full mesh with drive pinion teeth. Do not
tilt unit.
100.Note total reading obtained on dial gauge.
101.From this figure subtract 0,25 mm to obtain
correct crown wheel backlash when fitted. The
result indicates value of shimming to be fitted
between differential case and bearing cone at
crown wheel side of differential.
102.Fit shim value determined in instruction 101,
taking shims from pack previously determined
during 'Differential bearing adjustment' checks,
instructions 57 to 62LRT-51-500details 1 and 2,
pressLRT-99-002, andLRT-51-504.
103.Fit remaining shims from instruction 101 to
opposite side of differential.LRT-51-501details
1 and 2, pressLRT-99-002, andLRT-51-504.
104.Fit differential unit with shims and bearings to
axle casing, using axle spreaderLRT-51-503
with pegs18G131F.
105.Remove axle spreader.106.Fit bearing caps in their correct position,
referring to relationship markings on caps and on
axle casing.
107.Tighten bearing caps fixings to
135 Nm (100
lbf/ft).
108.Mount a dial gauge on axle casing with stylus
resting on a crown wheel tooth.
109.Prevent drive pinion from rotating and check
crown wheel backlash which must be 0,15 to
0,27 mm. If backlash is not within specified
limits, repeat differential backlash checks,
instructions 96 to 102 looking for possible errors.
110.Fit differential cover and new gasket, coating
both sides of gasket with Hylomar PL 32M or an
equivalent non-setting sealant. Torque load for
fixings is
30 Nm (22 lbf/ft).
111.Reverse instructions 3 to 5 and coat threads of
hub driving member bolts with Loctite 'Studlock'
grade CVX and fit and tighten bolts evenly to
correct torque.
112.Fit rear axle assembly to vehicle
See Repair,
Rear axle
.
113.Replenish differential with recommended
lubricant
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
lubricants and fluids
. After initial axle run,
check oil level and replenish as necessary to
filler/level plug hole.
114.Where major running parts have been replaced
during servicing, it is a recommended practice to
allow axle assembly to 'run in' by avoiding,
where possible, heavy loads and high speeds
during initial running.

51REAR AXLE AND FINAL DRIVE
10
OVERHAUL REAR HUB ASSEMBLY - 90
Service repair no - 64.15.13.
1.Remove rear hub
See Repair, Rear hub
assembly
.
2.Remove outer bearing.
3.Mark, for reassembly, position of hub to brake
disc.4.Remove 5 bolts and separate hub from brake
disc.
WARNING: A maximum of two road wheel
retaining studs can be renewed. Should
more studs be unserviceable fit new hub
with studs.
5.Remove grease seal and inner bearing from
hub.
6.Remove inner and outer bearing tracks.
REAR HUB COMPONENTS - 90
1.Axle shaft.
2.Axle shaft joint washer.
3.Axle shaft retaining bolt.
4.Lock nut.
5.Lock washer.
6.Hub adjusting nut.
7.Spacing washer.8.Outer bearing.
9.Hub.
10.Inner bearing.
11.Grease seal.
12.Brake disc.
13.Disc retaining bolt.

REAR AXLE AND FINAL DRIVE
13
OVERHAUL REAR HUB - 110/130
Service repair no - 64.15.14.
Overhaul
1.Remove rear hub assembly
See Repair, Rear
hub assembly.
2.Remove outer bearing.
3.Mark, for reassembly, relationship between hub
and brake disc, if original hub is to be refitted.
4.Remove 5 bolts and separate hub from brake
disc.
5.Drift out grease seal and inner bearing from hub
and discard seal.
HUB COMPONENTS
1.Dust cap.
2.Drive shaft circlip.
3.Drive member.
4.Drive member joint washer.
5.Drive member retaining bolt.
6.Lock nut.
7.Lock washer.
8.Hub adjusting nut.9.Spacing washer.
10.Outer bearing.
11.Hub.
12.Inner bearing.
13.Grease seal.
14.Brake disc.
15.Disc retaining bolt.

FRONT AXLE AND FINAL DRIVE
1
DESCRIPTION AND OPERATION DESCRIPTION
The welded steel front axle casing houses a separate
spiral bevel type differential unit, which is off-set to the
right of the vehicle centre line. The differential unit
drives the front wheels via the axle shafts and
constant velocity joints which are totally enclosed in
the spherical and swivel housings.The front wheels are pivoted on tape roller bearings at
the top and bottom of the swivel housing. The wheel
hubs on all axles are supported by two taper bearings
and driven by drive flanges which are splined to the
one piece, stub shaft/constant velocity joint.
Front axle hub and swivel housing
1.Axle casing
2.Ventilation pipe
3.Axle shaft
4.Wheel studs and hub
5.Stub axle
6.Wheel bearings
7.Inner and outer hub seals
8.Axle shaft seal
9.Hub lock plate, thrust washer and nuts
10.Brake disc
11.Drive flange
12.Shim washer and circlip13.Dust cap
14.Constant velocity joint/shaft
15.Thrust collar for CV joint
16.Roller bearing
17.Spacer
18.Circlip
19.Top and bottom swivel taper bearing
20.Top and bottom swivel pins
21.Spherical housing, seal and retainer
22.Swivel housing
23.Constant velocity shaft seal

FRONT AXLE AND FINAL DRIVE
1
FAULT DIAGNOSIS FAULT DIAGNOSIS
Complaint - Oil leaks
An external leak of lubrication can be caused by a
faulty internal seal. For example, if the seals which
separate the differential from the swivel housings are
faulty and the vehicle is operating or parked on an
embankment, oil may leak across the axle leaving one
swivel with a high level and the opposite swivel and
differential lacking lubrication.
See 'Description and Operation' for illustrations of oil
seal locations.
When investigating leaks or checking oil levels, it is
essential that all the lubrication is drained from any
housing with a high level and that the other levels are
checked.
Swivel oil should be checked for signs of grease
leaking from the hub bearings and oil contamination of
the hub grease.
Check that the axle ventilation system is clear, as a
blockage can cause internal pressure to force oil past
the seals.
If the vehicle is driven in deep water with defective oil
seals, water may contaminate the lubricants and when
checked, give a false impression that the housing has
been overfilled with oil.
Do not assume that a high oil level is due to over
filling or, that a low level is because of an external
leak.

54FRONT AXLE AND FINAL DRIVE
2
REPAIR FRONT HUB ASSEMBLY
Service repair no - 60.25.01.
Remove
1.Loosen front wheel nuts, jack up vehicle and
lower onto axle stands and remove road wheel.
2.Release brake hose clips and remove brake
caliper and brake disc shield bolts. Secure to
one side.3.Lever off dust cap.
4.Remove circlip and drive shaft shim from
driveshaft.
5.Remove 5 bolts and withdraw driving member
and joint washer.
6.Bend back lock washer tabs.
7.Remove locknut and lock washer.
8.Remove hub adjusting nut.
9.Remove spacing washer.
10.Remove hub and brake disc assembly complete
with bearings.
HUB COMPONENTS
1.Dust cap.
2.Drive shaft circlip.
3.Drive shaft shim.
4.Drive member.
5.Drive member joint washer.
6.Drive member retaining bolt.
7.Lock nut.
8.Lock washer.9.Hub adjusting nut.
10.Spacing washer.
11.Outer bearing.
12.Hub.
13.Inner bearing.
14.Grease seal.
15.Brake disc
16.Disc retaining bolt.

FRONT AXLE AND FINAL DRIVE
3
REPAIR REV: 05/99 Refit
11.Clean stub axle and drive shaft and fit hub
assembly to axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
50 Nm (37
lbf/ft).
Ensure hub is free to rotate with no
bearing play.
14.Back off adjusting nut 90°and tighten to
10 Nm
(7 lbf/ft).
15.Fit a new lock washer.
16.Fit locknut. Tighten to
50 Nm (37 lbf/ft).
17.Tab over lock washer to secure adjusting nut
and locknut.
18.Fit a new joint washer to driving member and fit
member to hub. Tighten bolts to
65 Nm (48
lbf/ft).
19.Fit original drive shaft shim and secure with a
circlip.
20.To check drive shaft end play, mount a dial
gauge using bracketLRT-99-503and rest pin in
a loaded condition on end of drive shaft.
21.Fit a suitable bolt to threaded end of drive shaft.
Move drive shaft in and out noting dial gauge
reading. End play should be between 0,08 to
0,25 mm.
22.If end play requires adjustment, remove circlip,
measure shim thickness and fit an appropriate
shim to give required end-play.
23.Remove bolt from drive shaft, fit circlip and dust
cap.
24.Fit brake disc shield and brake caliper. Tighten
fixings to
82 Nm (60 lbf/ft).
25.Bleed brake systemSee BRAKES, Repair,
Brake system bleed
.
26.Fit road wheel, remove axle stands and tighten
road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
27.Operate footbrake to locate brake pads before
driving vehicle.

FRONT AXLE AND FINAL DRIVE
5
OVERHAUL 38.Place retaining plate, joint washer and oil seal
over axle flange ready for assembly.
39.Fit swivel bearing housing to axle flange with 7
bolts. Tighten to
73 Nm (54 lbf/ft).
40.Grease and fit upper and lower swivel pin taper
roller bearings.
41.Position swivel pin housing over swivel bearing
housing.
42.Coat joint washer both sides with sealing
compound and position on lower swivel pin.
43.Loosely fit brake shield bracket plus lower swivel
pin with lug outboard to swivel pin housing.
44.Loosely fit top swivel pin plus existing shims and
brake hose bracket to swivel pin housing.
45.Apply Loctite 270 or equivalent to lower swivel
pin bolts.
78 Nm (58 lbf/ft),bend over lock tabs.
46.Tighten top swivel pin bolts to
78 Nm (58 lbf/ft).
Check and adjust preload on bearings
NOTE: Swivel housing oil seal and axle
should not be fitted.
47.Attach a spring balance to ball joint bore and pull
balance to determine effort required to turn
swivel pin housing.
Resistance, once initial inertia has been
overcome, should be1.16 to 1.46 kg.Adjust by
removing or adding shims to top swivel pin.
48.When setting is correct remove top swivel bolts,
apply Loctite 270 or equivalent. Refit bolts and
tighten to
78 Nm (58 lbf/ft),and bend over lock
tabs.
49.Apply recommended grease between lips of
swivel oil seal.50.Fit oil seal, joint washer and retaining plate with
7 bolts and spring washers. Tighten to
11 Nm (8
lbf/ft).
51.Fit tie rod and drag link and secure with new
cotter pins. Tighten fixing to
40 Nm (30 lbf/ft).
52.Fit brake disc shield.
53.Loosely fit lock stop bolt and nut.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to
11 Nm (8 lbf/ft).
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.
Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 O'clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle before stub axle is
secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with 6 bolts and
tighten evenly to
65 Nm (48 lbf/ft).
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit complete front hub assembly
See Repair,
Front hub assembly
.
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil
See SECTION 10, Maintenance, Under
vehicle maintenance
.
NOTE: On later vehicles fill swivel pin
housing with 0.33 Litres of Molytex EP 00
grease.
67.Set steering lock stop bolts
See STEERING,
Adjustment, Steering lock stops
.

57STEERING
2
DESCRIPTION AND OPERATION
Power steering box components
1.Housing complete with sector shaft bearings
2.Cover plate complete with bearing
3.Sector shaft
4.Hydraulic piston/rack
5.Worm/valve and torsion bar assembly
6.Shims for centralizing worm/valve
7.Ball race
8.'Teflon' seals for valve sleeve
9.Bearing adjuster, locknut and seal
10.Worm shaft pressure seal, circlip and dirt
excluder11.'Teflon' and rubber seal for piston
12.End cover seal and snap ring
13.Adjustment components for piston/rack
14.Hydraulic pipe
15.Bleed screw
16.Sector shaft adjustment lock nut with seal
17.Cover plate bolts
18.Cover plate seal
19.Seal, washer and backup seal
20.Circlip and dust cover