service LAND ROVER DEFENDER 1999 Workshop Manual

70BRAKES
8
REPAIR Refit
14.Clean caliper to hub mating faces.
15.Position caliper to hub, fit bolts and tighten to82
Nm (60 lbf.ft).
16.Remove plugs from pipe to caliper connections
and wipe.
17.Connect pipe to caliper, tighten union to15 Nm
(11 lbf.ft).
18.Apply a light film of grease to rear of brake pads.
19.Fit pads to calipers.
From 02MY, ensure pads are correctly fitted,
with leading edge chamfer fitted as shown.
20.Fit pad retainers and springs.
21.Fit split pins to retainers.
22.Remove brake hose clamp.
23.Bleed brakes.See Adjustment.
24.Depress brake pedal to seat pads onto discs.
25.Fit road wheels, remove axle stands and tighten
nuts to130 Nm (96 lbf.ft).BRAKE CALIPER - REAR
Service repair no - 70.55.03
Remove
1.Loosen rear road wheel nuts.
2.Raise rear of vehicle.
WARNING: Support on safety stands.
3.Remove road wheel.
4.Remove split pins from brake pad retaining pins.
5.Remove brake pad retaining pins.
6.Remove brake pad retainer springs.
7.Remove brake pads and shim if fitted.
8.Position container beneath brake caliper to
collect spillage.
9.Loosen brake pipe union and disconnect from
caliper.
CAUTION: Plug the connections.
10.Remove 2 bolts securing caliper.
11.Remove brake caliper.
ProCarManuals.com

BRAKES
9
REPAIR Refit
12.Clean caliper to axle bracket mating faces.
13.Position caliper to axle bracket, fit bolts and
tighten to82 Nm (60 lbf.ft).
14.Remove plugs from pipe and caliper.
15.Clean brake pipe union and caliper.
16.Connect pipe to caliper, tighten union to15 Nm
(11 lbf.ft).
17.Apply a light film of grease to rear of brake pads.
18.Fit brake pads.
From 02MY, ensure shims are correctly fitted,
see illustration.
NOTE: Vehicles from 02MY have leading
and trailing edge chamfers on rear pads.
19.Fit pad retainer springs.
20.Fit brake pad retaining pins and secure with new
split pins.
21.Bleed brakes.See Adjustment.
22.Depress brake pedal to seat pads onto discs.
23.Fit road wheels, remove axle stands and tighten
nuts to130 Nm (96 lbf.ft).SWITCH - STOP LIGHT
Service repair no - 70.35.42
Remove
1.Disconnect 2 Lucars from stop light switch.
2.Remove mastic from around switch.
3.Remove switch from pedal box.
Refit
4.Fit and tighten switch to pedal box.
5.Apply mastic to switch.
6.Connect 2 Lucars to switch.
ProCarManuals.com

70BRAKES
10
REPAIR FRONT BRAKE PADS - FROM 02MY
Service repair no - 70.40.02
Remove
1.Remove front road wheels.
2.Clean exterior of calipers.
3.Remove split pin from retaining pins.
4.Remove pad retaining pins and anti-rattle
springs.
5.Remove brake pads.
6.Clean exposed parts of pistons, using new brake
fluid. Wipe away excess with a lint free cloth.
7.Using piston clampLRT-70-500press each
piston back into its bore. Ensure that displaced
brake fluid does not overflow from reservoir.
Refit
8.Fit brake pads.
NOTE: Ensure pads are correctly fitted,
with leading edge chamfer fitted as shown.
9.Fit pad retaining pins and anti-rattle springs.
Secure with new split pins.
ProCarManuals.com

BRAKES
11
REPAIR 10.Apply service brake pedal several times to locate
pads.
11.Fit road wheels, remove chassis stands and
jack. Tighten wheel nuts to130 Nm (96 lbf/ft).
12.Check fluid reservoir. Top up if necessary, using
correct grade of fluid.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information.REAR BRAKE PADS - FROM 02MY
Service repair no - 70.40.03
Remove
1.Remove rear road wheels.
2.Clean exterior of calipers.
90 Models
110/130 Models
3.Remove pad retaining pins and anti-rattle
springs. Note differences between 90 and
110/130 models.
4.Remove brake pads and shims.
ProCarManuals.com

70BRAKES
12
REPAIR 5.Clean exposed parts of pistons, using new brake
fluid.
6.Wipe away excess fluid with lint free cloth.
7.Using piston clampLRT-70-500press each
piston back into its bore. Ensure that displaced
brake fluid does not overflow from reservoir.
Refit
8.Fit brake pads and shims.
Ensure shims are correctly fitted, see illustration.
NOTE: Vehicles from 02MY have leading
and trailing edge chamfers on rear pads.
Shims are also fitted.
9.Fit anti-rattle springs and secure with retaining
pins.10.Apply service brake pedal several times to locate
pads.
11.Fit road wheels, remove chassis stands and
jack. Tighten wheel nuts to130 Nm (96 lbf/ft).
12.Check fluid reservoir, top up if necessary, using
correct grade of fluid.See LUBRICANTS,
FLUIDS AND CAPACITIES, Information.
ProCarManuals.com

CHASSIS AND BODY
3
DESCRIPTION AND OPERATION The tail door for 02MY is completely redesigned to address manufacturing complexity, corrosion and water ingress
probelms on previous tail doors.
The tail door is now a one piece outer skin pressing located on a reinforced steel, zinc plated frame. This gives
improved build quality, water integrity and minimal welding.
A new tail door glass is introduced with a one piece continuous rubber seal. The tail door glass has a revised
Heated Rear Window (HRW) element on the glass which removes the need to route wires up the sides of the
frame. The HRW element now has integral Lucar connections in the element which provide the earth connections
for the new centre high mounted stop lamp.
The inner trim panel is new and accommodates the CDL actuator and linkages.
The new tail door also contains a relay for rear wiper motor operation. Refer to the Wipers section for details.
Because the new tail door uses the current hinges and latch and retains the same geometry as the previous tail
door, the new tail door assembly is available as a service item for current vehicles.
ProCarManuals.com

CHASSIS AND BODY
1
ADJUSTMENT TAIL DOOR STRIKER
Service repair no - 76.37.25
Check
1.Before adjusting door striker, ensure spare
wheel is fitted to tail door.
Adjust
1.Loosen bolts securing striker.
2.Adjust striker and tighten bolts to10 Nm (7
lbf.ft).
3.Close door and check for correct latching.
ProCarManuals.com

CHASSIS AND BODY
1
REPAIR PANEL - UNDERBELLY - FRONT AND CENTRE
Service repair no - 76.10.50
Remove
1.Raise vehicle on 4 post ramp.
2.Mark front propellor shaft and front differential
flanges for reassembly.
3.Remove 4 bolts and release propellor shaft from
front differential.
4.Remove 12 bolts securing front and centre
underbelly panels.
5.Remove front and centre underbelly panels.
Refit
6.Position front and centre underbelly panels.
7.Fit and tighten bolts securing front and centre
underbelly panels.
8.Position front propellor shaft to differential and
tighten bolts to48 Nm (35 lbf.ft).
9.Lower vehicle.CUBBY BOX
Service repair no - 76.25.04
Remove
1.Open cubby box lid and remove 2 caps
concealing rear fixing bolts.
2.Remove bolts securing rear of cubby box.
3.Open flap concealing front fixing bolts.
4.Remove bolts securing front of cubby box.
5.Remove cubby box.
Refit
6.Fit cubby box to vehicle.
7.Fit bolts securing front of cubby box and
reposition flap.
8.Fit bolts securing rear of cubby box.
9.Fit caps over bolts.
10.Close cubby box lid.
ProCarManuals.com

76CHASSIS AND BODY
2
REPAIR TRIM CASING - TAIL DOOR - UP TO 02MY
Service repair no - 76.34.09
Remove
1.Remove 2 bolts securing grab handle to tail
door.
2.Remove grab handle.
3.Remove 2 screws securing wiper motor cover.
4.Remove wiper motor cover.
5.Remove 7 screws securing trim casing to door.
6.Remove 2 screws securing wiper motor harness
cover.
7.Remove harness cover.
8.Release 7 of 8 trim studs securing trim casing.
9.Remove trim casing from remaining stud.
10.Collect door lock cover.Refit
11.Position door lock cover.
12.Position trim casing and secure trim casing.
13.Position harness cover and secure with screws.
14.Secure trim pad with screws.
15.Fit wiper motor cover and secure with screws.
16.Fit grab handle and secure with screws.
ProCarManuals.com

CHASSIS AND BODY
3
REPAIR LATCH - TAIL DOOR - UP TO 02MY
Service repair no - 76.37.16
Remove
1.Remove tail door trim casing.See this Section.
2.Collect latch cover.
3.Remove 2 screws securing latch to door and
collect captive nut bracket.
4.Remove 2 nuts securing latch to door and collect
captive bolt bracket.
5.Remove latch assembly and collect foam
gasket.
Refit
6.Fit foam gasket and latch assembly to tail door.
7.Fit captive nut and bolt brackets to tail door.
8.Secure latch to tail door with nuts and screws.
9.Fit cover to latch.
10.Fit tail door trim casing.See this Section.CARPET - LUGGAGE COMPARTMENT
Service repair no - 76.49.04
Remove
1.Remove 7 screws and remove carpet retainer.
2.Remove bolt covers and remove rear seat belt
bolts.
3.Release rear seat catches and fold seats
forward.
4.Remove luggage compartment carpet.
Refit
5.Position carpet.
6.Fold rear seats to position.
7.Align rear seat belts and tighten tighten bolts.
8.Fit bolt covers.
9.Position carpet retainer and tighten screws.
ProCarManuals.com