LAND ROVER DEFENDER 1999 Workshop Manual

12ENGINE
22
OVERHAUL Refit
1.Clean crankshaft rear oil seal housing mating
face on cylinder block, ensure bolt and dowel
holes are clean and dry. Remove all traces of oil
from oil seal running surface on crankshaft.
2.Position seal protectorLRT-12-061over
crankshaft boss. Fit new seal and housing,
removeLRT-12-061.
CAUTION: Oil seal must be fitted dry.
3.Fit oil seal housing bolts and using sequence
shown, tighten to9 Nm (7 lbf.ft).
4.Fit sump gasket.See this Section.
5.Fit flywheel.See Repair.STARTER RING GEAR
Service repair no - 12.53.19
Remove.
1.Remove flywheel.See Repair.
2.Drill a 3 mm (0.12 in) diameter hole at root of 2
teeth.
3.Apply a cold chisel to root of teeth, break ring
gear and remove from flywheel.
WARNING: SUITABLE EYE PROTECTION
MUST BE WORN.
Refit
1.Heat ring gear evenly to 350°C, indicated by
light blue colour.
2.Locate ring gear on flywheel and press on to
flange.
WARNING: Handle hot ring gear with care.
3.Allow ring gear to air cool.
4.Fit flywheel.See Repair.
ProCarManuals.com

ENGINE
23
OVERHAUL PUMP - OIL
Service repair no - 12.60.26.02
Remove
1.Remove sump gasket.See this Section.
2.Remove bolt securing oil pump drive sprocket.
3.Release drive sprocket from chain, remove
sprocket.
4.Remove 3 Torx screws securing oil pick-up
strainer, remove strainer.
5.Remove and discard’O’ring.
6.Using sequence shown, remove and discard 22
bolts securing oil pump and stiffener plate
assembly to cylinder block.
7.Remove oil pump and stiffener plate assembly.
NOTE: Dowel located.
8.Remove and discard’O’ring from oil pump
housing outlet.
ProCarManuals.com

12ENGINE
24
OVERHAUL Inspection
CAUTION: Inspection/overhaul procedures
for the oil pump are limited to carrying out
dimensional checks. In the event of wear
or damage being found, a replacement pump and
stiffener plate assembly must be fitted.
Oil pump
1.Remove and discard 5 screws securing cover to
oil pump, remove cover.
2.Using a felt tipped pen, make suitable alignment
marks between inner and outer rotors and pump
body.
3.Remove inner and outer rotors.
4.Check rotors, cover and pump body for signs of
scoring and wear.
5.Fit rotors ensuring that reference marks are
aligned and identification mark on inner rotor is
facing outwards.
6.Using feeler gauges, check pump body to outer
rotor clearance:
Pump body to outer rotor clearance =0.295
to 0.375 mm (0.012 to 0.015 in)
7.Using feeler gauges, check clearance of inner to
outer rotor in 2 positions, both clearances must
be within limit given:
Inner to outer rotor clearance =0.13 mm (0.05
in)
ProCarManuals.com

ENGINE
25
OVERHAUL
8.Place a straight edge across pump body and
using feeler gauges, measure end-float of outer
rotor:
Outer rotor end-float =0.038 to 0.075 mm
(0.001 to 0.003 in)
9.Check drive shaft bush in pump cover for signs
of scoring and wear.
10.Renew oil pump and stiffener plate assembly if
excessive scoring exists or clearances exceed
limits given.
11.Lubricate pump rotors and drive shaft bush with
engine oil.
12.Fit rotors ensuring reference marks are aligned
and identification mark on inner rotor is facing
forwards.
13.Fit cover to pump, fit 5 new screws and tighten
by diagonal selection to6 Nm (4.5 lbf.ft).
14.Check that pump rotors rotate freely.Oil pressure relief valve
1.Remove and discard oil pressure relief valve
plug.
2.Remove spring and relief valve plunger.
3.Clean valve plunger and spring.
4.Check valve plunger and relief valve bore for
scoring and corrosion.
NOTE: Light scoring and corrosion may be
removed using grade 600 emery cloth
soaked in oil.
5.Check spring for distortion, check free length of
spring:
Spring free length =42.00 mm (1.65 in)
CAUTION: Renew relief valve as an
assembly.
6.Lubricate valve plunger and seating.
7.Fit valve plunger and spring to oil pump.
8.Apply Loctite 243 sealant to threads of a new
plug.
CAUTION: Do not attempt to fit original
plug.
9.Fit plug and tighten to23 Nm (17 lbf.ft).
ProCarManuals.com

12ENGINE
26
OVERHAUL Refit
1.Clean mating faces of oil pump, stiffener plate
assembly and cylinder block; ensure bolt and
dowel holes are clean and dry.
2.Lubricate a new’O’ring with engine oil and fit to
oil pump housing outlet.
3.Position oil pump and stiffener plate assembly
on to cylinder block ensuring 2 dowels are
correctly located.
4.Fit new bolts and using sequence shown, tighten
to13 Nm (10 lbf.ft).
5.Lubricate a new’O’ring with engine oil and fit to
oil pick-up strainer.
6.Clean threads of oil pick-up strainer Torx screws
and apply Loctite 242 to threads.
7.Fit oil pick-up strainer, fit Torx screws and
tighten to10 Nm (8 lbf.ft).
8.Position oil pump drive sprocket to chain and oil
pump ensuring that the’D’shape on the drive
sprocket is located on the flat on the oil pump
drive shaft.
9.Clean threads of oil pump drive sprocket
retaining bolt and apply Loctite 242 to threads.
10.Fit oil pump drive sprocket bolt and tighten to25
Nm (18 lbf.ft).
11.Fit sump gasket.See this Section.TIMING CHAIN AND SPROCKETS
Service repair no - 12.65.13.01
Remove
1.Remove cylinder head gasket.See this
Section.
CAUTION: If timing chain tensioner is to
be replaced, ensure tensioner is correct
for engine. Tensioner bodies are colour
coded as follows:- Engine Serial No. Prefixes 10P
to 14P - BLACK with, additionally, on later
engines, YELLOW on tensioner hex. head. Engine
Serial No. Prefixes 15P to 19P:- Body is coloured
YELLOW. Later tensioners may be fitted to early
engines provided that the modified adjustable
guide is also fitted.
2.Remove 3 bolts securing crankshaft damper to
pulley, remove damper.
3.PositionLRT-51-003to crankshaft pulley and
secure with 2 bolts.
4.Using assistance, restrain engine and remove
crankshaft pulley bolt; discard bolt.
WARNING: CRANKSHAFT BOLT IS
TIGHTENED TO 460 Nm (340 lbf.ft),
ENSURE THAT ENGINE IS ADEQUATELY
RESTRAINED.
5.Remove crankshaft pulley, remove bolts and
tool.
6.Remove sump gasket.See this Section.
ProCarManuals.com

ENGINE
27
OVERHAUL
7.Noting their fitted positions, remove 8 bolts
securing timing chain cover.
8.Remove timing chain cover.
NOTE: Dowel located.
9.Remove bolt securing oil pump drive sprocket.
10.Remove oil pump drive sprocket.
11.Remove camshaft and crankshaft sprockets
together with timing and oil pump drive chains.
12.Remove Woodruff key from crankshaft.
13.Remove 2 bolts and remove timing chain fixed
guide.
14.Remove bolt and remove timing chain adjustable
guide.
15.Remove bolt and remove timing chain lubrication
jet.
16.Using toolLRT-12-092, remove and discard oil
seal from timing cover.
ProCarManuals.com

12ENGINE
28
OVERHAUL Inspection
1.Clean all components.
2.Check condition of timing chain running surfaces
on adjustable and fixed guides.
CAUTION: Adjustable guide fitted to
Engine Serial No. Prefixes 15P to 19P may
be fitted to Engine Serial No. Prefixes 10P
to 14P provided that timing chain tensioner having
a YELLOW colour coded body is also fitted.
3.Check timing chains and sprockets for signs of
wear.
CAUTION: Timing chains and sprockets
fitted to Engine Serial No. Prefixes 15P to
19P may be fitted to Engine Serial No.
Prefixes 10P to 14P as an assembly only, oil pump
sprockets are interchangeable. Timing chains
fitted to Engine Serial No. Prefixes 15P to 19P
have BRONZE coloured timing links.
4.Check that drilling in timing chain lubrication jet
is clear.
5.Clean oil seal recess in timing cover and oil seal
running surface on crankshaft.
6.Remove all traces of sealant from mating faces
of timing cover and cylinder block using suitable
solvent.
CAUTION: Do not use metal scrapers.
7.Ensure bolt and dowel holes are clean and dry.
8.Clean oil pump sprocket bolt threads.Refit
1.Fit timing chain lubrication jet.
2.Fit bolt securing lubrication jet and tighten to10
Nm (7 lbf.ft).
3.If crankshaft has been rotated, check that No. 1
piston is at TDC using the following procedures:
4.Temporarily fit and lightly tighten a new
crankshaft pulley bolt.
5.Assemble a magnetic base DTI to cylinder block
top face, position stylus to cylinder block top face
and zero gauge.
6.Using crankshaft pulley bolt, rotate crankshaft
clockwise until No. 1 piston is at top of its stroke
and Woodruff key slot in crankshaft is at 12
o’clock position.
7.Position stylus of DTI to No. 1 piston crown and
rotate crankshaft until highest reading is
indicated on DTI.
8.Check that Woodruff key slot in crankshaft is still
at 12 o’clock position indicating No. 1 piston is at
TDC firing.
9.Remove DTI.
ProCarManuals.com

ENGINE
29
OVERHAUL 10.Remove crankshaft pulley bolt.
11.Fit Woodruff key to crankshaft.
12.Fit oil pump drive chain to rear row of teeth on
crankshaft sprocket i.e. teeth furthest away from
timing mark on sprocket.
13.Fit sprocket to crankshaft ensuring that timing
mark on sprocket is facing towards front end of
crankshaft.
14.Fit oil pump drive sprocket to oil pump and drive
chain ensuring that’D’shape on sprocket is
located on flat on oil pump drive shaft.
15.Apply Loctite 242 to threads of oil pump drive
sprocket bolt, fit bolt and tighten to25 Nm (18
lbf.ft).
16.Fit timing chain fixed guide, fit bolts and tighten
to:
M6 bolt -10 Nm (7 lbf.ft)
M10 bolt -45 Nm (34 lbf.ft)
17.Fit timing chain adjustable guide, fit bolt and
tighten to25 Nm (18 lbf.ft).
18.Fit camshaft sprocket to timing chain with timing
mark on sprocket between the 2 coloured links,
suitably retain sprocket to chain.
19.Fit timing chain to crankshaft sprocket aligning
coloured link to timing mark on sprocket.
CAUTION: Ensure timing marks are
positioned as shown - No. 1 piston at TDC
firing.
20.Apply an even film film of sealant, Part No. STC
4600 to mating face of timing cover and spread
to an even film using a roller.
CAUTION: Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.
21.Fit timing cover, fit bolts in their original fitted
positions and working from the centre outwards,
tighten progressively to27 Nm (20 lbf.ft).
ProCarManuals.com

12ENGINE
30
OVERHAUL
22.Fit oil seal guide, from seal kit, over end of
crankshaft.
23.Fit new oil seal into timing cover using
LRT-12-156.
CAUTION: Oil seal must be fitted dry.
24.RemoveLRT-12-156and oil seal guide.
25.Fit crankshaft pulley, fit crankshaft pulley bolt.
26.FitLRT-51-003to crankshaft pulley and secure
with 2 bolts.
27.Using assistance, restrain engine and using a
torque multiplier, tighten crankshaft bolt to460
Nm (340 lbf.ft).
WARNING: DUE TO THE HIGH TORQUE
LOADING REQUIRED, IT IS ESSENTIAL
THAT ENGINE IS ADEQUATELY
RESTRAINED.
28.RemoveLRT-51-003.
29.Position damper to crankshaft pulley, fit 3 bolts
and tighten to80 Nm (60 lbf.ft).
30.Fit sump gasket.See this Section.
31.Fit cylinder head gasket.See this Section.BEARINGS - CONNECTING RODS
Service repair no - 12.17.16.01
Remove
1.Remove oil pump.See this Section.
2.Mark cylinder reference number on each
connecting rod big-end bearing cap.
3.Make suitable alignment marks between each
big-end bearing cap and connecting rod.
CAUTION: Due to the’fracture split’
method of manufacturing connecting rods
and bearing caps, incorrect fitting of cap
to connecting rod will damage mating faces and
necessitate replacement of connecting rod
assembly.
4.Rotate crankshaft clockwise until No. 1 big-end
is at BDC.
5.Remove and discard 2 bolts securing No. 1
big-end bearing cap.
6.Remove bearing cap, remove and discard
big-end bearing shell.
7.Push connecting rod up cylinder bore until rod is
clear of crankshaft journal.
CAUTION: Ensure that connecting rod
does not contact cylinder bore or oil squirt
jet and piston does not contact the valves
or EUI’s if the cylinder head is fitted.
ProCarManuals.com

ENGINE
31
OVERHAUL 8.Remove and discard big-end bearing shell from
connecting rod.
CAUTION: Engine Serial No. Prefixes 10P
to 14P:- The’sputter type’connecting rod
bearings fitted to these engines, identified
by them having a slightly darker colour than the
bearing cap shells should be replaced with the
’plain type’bearing shells fitted to Engine Serial
No. Prefixes 15P to 19P.
9.Repeat above procedures for remaining big-end
bearings.
CAUTION: Keep bearing caps in their fitted
order.
Inspection
NOTE: If crankshaft is to be removed,
big-end bearing journals should be
checked when crankshaft is inspected.
1.Check each big-end bearing journal for scoring,
wear and ovality, make 3 checks at 120°intervals
in centre of journal:
Big-end journal diameter =
54.000±0.01 mm (2.125±0.0004 in)
CAUTION: Big-end journals may not be
reground undersize,only one size of
big-end bearing shell is available and if
journals are found to be scored, oval or worn,
crankshaft must be replaced. Big-end bearing
shells must be replaced whenever they have been
removed.Refit
1.Clean connecting rod journals and bearing shell
locations.
2.Lubricate new big-end bearing shells with engine
oil and fit to connecting rods and bearing caps
ensuring that the’sputter bearings’are fitted to
the connecting rods.
NOTE:’Sputter type’bearing shells can be
identified by them by having a slightly
darker colour.
3.Rotate crankshaft until No. 1 big-end bearing
journal is at BDC.
4.Taking care not to damage oil squirt jet or to
displace bearing shell, pull connecting rod on to
crankshaft journal.
5.Check that bearing shell is correctly located in
big-end bearing cap.
6.Fit No. 1 big-end bearing cap ensuring that
reference marks are aligned.
7.Lightly oil threads of new big-end bearing cap
bolts, fit bolts and tighten to:
Stage 1 -20 Nm (15 lbf.ft)
Stage 2 -Further 80
°
CAUTION: Do not carry out stages 1 and 2
in one operation.
ProCarManuals.com