engine LAND ROVER DISCOVERY 1995 Workshop Manual

12ENGINE
4
DESCRIPTION AND OPERATION CYLINDER BLOCK COMPONENTS
1. Cylinder block
2. Knock sensor
3. Crankshaft sensor
4. Bolt - crankshaft sensor
5. Locating dowel - cylinder head
6. Bolt - connecting rod
7. Piston
8. Piston ring - top compression
9. Piston ring - 2nd compression
10. Piston ring - oil control
11. Gearbox adapter plate
12. Bearing shell - big end - upper
13. Flywheel
14. Bolt - flywheel
15. Torx screw - gearbox adapter plate
16. Blanking plate
17. Bolt - blanking plate
18. Gasket
19. Bolt - crankshaft rear oil seal housing
20. Crankshaft rear oil seal and housing
21. Bolt - coolant pump cover
22. Coolant pump cover
23. Impeller
24. Sealing rings
25. 'O' ring
26. Bolts - coolant pump
27. 'O' ring
28. Coolant pump body
29. Thrust washer halves - upper
30. Bearing shell - main bearing - upper
31. Locating dowel - oil pump
32. Locating dowel - flywheel
33. Gudgeon pin34. Crankshaft
35. Bearing shell - big end - lower
36. Bearing cap - big end
37. Nut - big end bearing cap
38. Locating dowel - main bearing cap
39. Bearing caps - main bearings
40. Bolt - main bearing cap
41. Thrust washer halves - lower
42. Bearing shell - main bearing - lower
43. Woodruff keys
44. Dipstick
45. Bolt - dipstick tube
46. Dipstick tube
47. Bolts - sump
48. Gasket - sump
49. 'O' ring
50. Oil strainer
51. Bolts - oil strainer
52. Sump
53. Washer - drain plug
54. Drain plug
55. Oil filter element
56. Crankshaft front oil seal
57. Bolts - oil pump
58. Gasket - oil pump
59. Oil pump
60. Oil pressure switch
61. Crankshaft spigot bush
62. Crankshaft spigot bearing
63. Locating dowel - coolant pump
64. Connecting rod
65. Bolts belt tensioner mounting plate
66. Belt tensioner mounting plate
67. Bolt - gearbox adapter plate

12ENGINE
6
DESCRIPTION AND OPERATION CYLINDER HEAD COMPONENTS
1. Engine oil filler cap
2. Filler cap seal
3. Screw - spark plug cover
4. Spark plug cover
5. h.t. lead plate
6. Screw - h.t. lead plate
7. Inlet camshaft cover
8. Exhaust camshaft cover
9. Bolt - exhaust camshaft cover
10. Exhaust camshaft cover gasket/baffle plate
11. Bolt - exhaust camshaft carrier
12. Exhaust camshaft carrier
13. Exhaust camshaft
14. Cylinder head bolt
15. Blanking plate
16. Bolt - blanking plate
17. Locating dowel - camshaft carrier
18. Coolant outlet elbow
19. Gasket
20. Bolt - coolant outlet elbow
21. Stud - exhaust manifold
22. Cylinder head gasket
23. Guide - exhaust valve24. Insert - exhaust valve seat
25. Exhaust valves
26. Inlet valves
27. Insert - inlet valve seat
28. Guide - inlet valve
29. Cylinder head
30. Stud - inlet manifold
31. Valve stem oil seal
32. Valve spring
33. Valve spring cap
34. Collets
35. Tappet
36. Camshaft oil seals
37. Drive pins - camshaft timing gears
38. Inlet camshaft
39. Inlet camshaft carrier
40. Bolt - inlet camshaft carrier
41. Inlet camshaft cover gasket/baffle plate
42. Bolt - inlet camshaft cover
43. Spark plug
44. Coolant temperature sensor
NOTE: Items 15,16 & 36 on current engines
replaced by an oil plug.
See Repair, Inlet -
Exhaust Camshaft Rear Oil Plug

12ENGINE
8
DESCRIPTION AND OPERATION TIMING BELT COMPONENTS
1. Bolt - timing belt upper cover
2. Timing belt upper cover
3. Bolt - camshaft timing gear
4. Plain washer
5. Timing belt
6. Inlet camshaft timing gear
7. Exhaust camshaft timing gear
8. Bolt - upper timing cover backplate
9. Upper timing cover backplate
10. Lower timing cover backplate
11. Tensioner spring sleeve
12. Anchorage bolt13. Tensioner spring
14. Tensioner pulley
15. Tensioner clamp bolt
16. Crankshaft timing gear
17. Timing belt lower cover
18. Bolt - timing belt lower cover
19. Timing belt centre cover
20. Crankshaft pulley
21. Crankshaft pulley/timing gear bolt
22. Crankshaft pulley bolt

12ENGINE
2
REPAIR 13.Remove 2 bolts securing camshaft gears to
camshafts.
14.Remove tool LRT-12-060.
CAUTION: Do not rotate camshafts.
15.Remove gears noting the 'IN' and 'EXHAUST'
identifying marks.
16.Remove 5 bolts securing timing belt upper
backplate.
17.Remove belt upper backplate.
18.Remove seals using tool LRT-12-063 fit
thrustpad as shown.
Refit
1.Clean sealing area of cylinder head and
camshaft, ensure all traces of rubber are
removed - do not scrape.
2.Using tool LRT-12-064 and LRT-12-072 fit new
camshaft oil seals.
CAUTION: Ensure sealing lip of seal is not
distorted.

12ENGINE
4
REPAIR CRANKSHAFT FRONT OIL SEAL
Service repair no - 12.21.14
Remove
1.Remove timing belt.
See Camshaft Drive Belt
2.Slide timing gear off crankshaft and remove
drive key.
3.Ensure bore of tool is burr free, fit and tighten
tool LRT-12-073 into crankshaft front oil seal.
4.Using thrustpad, tighten centre screw of tool to
remove oil seal.
5.Remove thrust button from crankshaft.
Refit
1.Use lint free cloth and thoroughly clean seal
recess and running surface on crankshaft. Clean
crankshaft gear and pulley.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-070 onto crankshaft.
4.Position new oil seal on crankshaft, drift into
place using LRT-12-069 and remove protector.
5.Fit drive key to crankshaft and slide timing gear
onto crankshaft.
6.Fit and tension timing belt.
See Camshaft
Drive Belt

Mpi
5
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
1.Remove gearbox.
2.Remove clutch assembly.
3.Remove flywheel.
4.Drain engine oil.
5.Fit sump plug, replacing sealing washer if
damaged and tighten to the correct torque.
6.Loosen 15 sump bolts by approximately 3 turns,
allowing sump to drop away from rear oil seal
housing. Do not loosen 3 boltsAaround oil
pump housing.
7.Remove bolts securing oil seal housing, remove
seal and housing assembly.
Refit
1.Clean seal seating area of block and accessible
area of sump gasket. Sump gasket must be
replaced if damaged.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-061 over crankshaft boss and fit
oil seal and housing assembly.
4.Remove tool.
5.Fit and tighten seal housing bolts to correct
torque in sequence shown.
10Nm
6.Tighten sump bolts to correct torque and in the
correct sequence.
See Engine Sump Gasket
7.Fit flywheel.
8.Fit clutch assembly.
9.Fit gearbox.

12ENGINE
6
REPAIR ENGINE
Service repair no - 12.41.01
Remove
1.Site vehicle onto ramp [hoist].
2.Remove the drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator - Mpi
4.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
5.Drain engine oil.
6.Position absorbent cloth around fuel pipe to fuel
rail union.
Unscrew union to relieve pressure.
CAUTION: Plug the connections
7.Release clip and disconnect hose from coolant
pump.
8.Release clip and disconnect hose from heater
rail.

12ENGINE
8
REPAIR 21.Release clip and disconnect inlet hose from
power steering pump.
22.Disconnect outlet pipe union at power steering
pump, discard 'O' ring.
CAUTION: Plug the connections
23.Release throttle cable from abutment bracket.
24.Release throttle cable from cam. Also remove
coolant bypass hose from throttle housing.
25.Disconnect stepper motor and throttle
potentiometer multiplugs.
26.Release clip and disconnect hose, air cleaner to
throttle housing.
27.Release clip and disconnect brake servo hose
from manifold.
28.Disconnect fuel temperature sensor multiplug.

Mpi
9
REPAIR 29.Disconnect oil pressure switch multiplug.
30.Disconnect air conditioning compressor
multiplug.
31.Remove 3 bolts securing engine harness to
manifold and fuel pipe.
32.Disconnect knock sensor multiplug.
33.Remove 2 nuts securing harness to starter motor
solenoid, remove harness.
34.Disconnect crankshaft sensor multiplug.
35.Disconnect fuel injection harness multiplug.
36.Disconnect inlet manifold air temperature sensor
multiplug.
37.Release clip and disconnect fuel hose from
pressure regulator.
CAUTION: Plug the connections.

12ENGINE
10
REPAIR
38.Disconnect 2 ignition coil multiplugs.
39.Disconnect 3 vacuum hoses from manifold.
40.Release cover and remove bolt securing earth
lead to cylinder block.
41.Move earth lead aside.
42.Remove 4 bolts securing air conditioning
compressor, move compressor aside.