torque LAND ROVER DISCOVERY 1995 Service Manual

MFI
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Air-Bypass valve (stepper motor) 20...............................................................
All flexible hose securing clamps 1,3...............................................................
Fuel feed pipe - hose to fuel rail 22.................................................................
Fuel filter 31....................................................................................................
EVAPORATIVE LOSS CONTROL SYSTEM
All flexible hose securing clamps 1,7...............................................................
METRIC Nm
M5 6...........................................................................
M6 9...........................................................................
M8 25...........................................................................
M10 45.........................................................................
M12 90.........................................................................
M14 105.........................................................................
M16 180.........................................................................
UNC / UNF
1/4 9...........................................................................
5/16 24.........................................................................
3/8 39...........................................................................
7/16 78.........................................................................
1/2 90...........................................................................
5/8 136...........................................................................
NOTE: Torque values above are for all screws and bolts used except for those specified.

SFI
3
REPAIR FUEL SYSTEM - DEPRESSURISE
WARNING: Fuel pressure of up to 2.5 bar
will be present in the system, even if the
engine has not been run for some time.
Always depressurise the system before
disconnecting any components in the fuel feed
line (between fuel pump and pressure regulator).
The spilling of fuel is unavoidable during this
operation. Ensure that all necessary precautions
are taken to prevent fire and explosion.
NOTE: Fuel pressure can be relieved at
fuel rail feed union or fuel filter unions.
1.Position cloth around relevant union to protect
against fuel spray.
2.Carefully slacken union.
3.Tighten union to correct torque once pressure
has relieved.

19FUEL SYSTEM
10
REPAIR KNOCK SENSOR
Service repair no - 18.30.28 - Sensor - LH
Service repair no - 18.30.30 - Sensor - RH
CAUTION: Due to the sensitivity of the
sensors, do not apply tape or sealant to
sensor threads.
Remove
1.Raise vehicle on ramp.
2. RH Sensor only:Remove bolt securing starter
motor heatshield to RH engine mounting.
3.Release heatshield clip from starter solenoid.
4.Move heatshield aside for access to knock
sensor.
5. Both sensors:
Disconnect sensor multiplug.
6.Remove sensor.
Refit
7.Clean sensor and mating face.
8.Fit sensor. Tighten to
16 Nm.
9.Connect sensor multiplug.
10. RH Sensor only:Manoeuvre heatshield into
position.
11.Secure clip to solenoid.
12.Align bracket to mounting and fit bolt. Fit and
tighten bolt.
13.Lower ramp.
CAUTION: Failure to tighten sensor to
correct torque will result in malfunction or
sensor damage.

19FUEL SYSTEM
22
REPAIRADD: 09/95
12.Mark location of anti-roll [sway] bar straps.
13.Remove nuts and bolts securing anti-roll [sway]
bar straps, and allow bar to swing down clear of
tank.14.Disconnect pressure sensor breather pipe
connection.
15.Disconnect vent line quickfit connector from
liquid/vapour separator.
16.Remove torque screw cap from hose to tank
filler neck clip.
17.Loosen clip screw securing hose to tank filler
neck.
18.Release hose from filler neck and internal filler
neck breather hose from fuel tank.
19.Remove and discard fuel filler neck clip.

SFI
27
REPAIR ADD: 09/95
11.Disconnect vent line quickfit connector from
liquid/vapour separator.
12.Remove torque screw cap from hose to tank
filler neck clip.
13.Loosen clip screw securing hose to tank filler
neck.
14.Release hose from filler neck and internal filler
neck breather hose from fuel tank.
15.Remove and discard fuel filler neck clip.
16.Disconnect the pressure sensor breather pipe
connection.
17.Disconnect the vent line hose connection.
18.Fit ignition key to fuel filler flap lock and open
flap.
19.Release fuel filler cap from filler neck.
20.Remove filler neck assembly from vehicle.
Do not carry out further dismantling if
component is removed for access only.
21.Remove torque screw cap from hose to filler
neck clip.
22.Loosen clip screw securing hose to filler neck.
23.Remove hose from filler neck.
24.Remove and discard fuel filler hose clip.
25.Remove vent line from filler neck.

Mpi
1
REPAIR KNOCK SENSOR
Service repair no - 18.30.18
Remove
1.Disconnect multiplug from knock sensor.
2.Remove knock sensor.
Refit
3.Clean mating face of cylinder block.
4.Fit knock sensor. Tighten to
15 Nm
5.Connect multiplug.IGNITION COILS
Service repair no - 18.20.40 - 1 & 4 Cylinders
Service repair no - 18.20.41 - 2 & 3 Cylinders
Remove
1.Disconnect battery negative lead.
2.Disconnect 4 h.t. leads from coils.
NOTE: Mark the position of the h.t. leads
to ensure correct refitment.
3.Disconnect 2 multiplugs from coils.
4.Disconnect crankshaft sensor multiplug.
5.Remove screw securing crankshaft sensor
multiplug to coil bracket.
6.Remove 3 bolts securing coil bracket to bell
housing.
NOTE: Access to the rear bolts is from
under the vehicle.
7.Remove coil assembly.
Refit
8.Position coil assembly to bell housing.
9.Fit 3 bolts and tighten to the correct torque.
10.Secure crankshaft sensor multiplug to coil
bracket with screw.
11.Connect crankshaft sensor multiplug.
12.Connect multiplugs and h.t. leads to coils.
13.Reconnect battery negative lead.

19FUEL SYSTEM
2
REPAIR COOLANT TEMPERATURE SENSOR
Service repair no - 18.30.10
Remove
1.Position drain tin below coolant pump hose.
2.Disconnect sensor multiplug.
3.Release harness clip and harness.
4.Remove sensor.
Refit
5.Clean sensor.
6.Fit sensor and tighten to the correct torque.
7.Position harness and secure with clip.
8.Connect multiplug.
9.Top-up cooling system.CRANKSHAFT SENSOR
Service repair no - 18.30.12
Remove
1.Position vehicle on ramp [hoist].
2.Disconnect multiplug from crankshaft sensor
flylead.
3.Remove screw, release lead from bracket.
4.Raise ramp [hoist].
5.Remove 2 bolts securing crankshaft sensor.
6.Remove crankshaft sensor.
Refit
7.Clean crankshaft sensor and mating surface of
backplate.
8.Fit crankshaft sensor, fit bolts. Tighten to
7Nm
9.Lower vehicle.
10.Position lead to bracket, fit and tighten screw.
11.Connect multiplug

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Oil cooler pipes 30..........................................................................................
Radiator filler plug (plastic) 6.........................................................................

MANIFOLD AND EXHAUST SYSTEM
7
REPAIR Refit
19.Ensure mating faces of inlet manifold and
cylinder head are clean.
20.Fit a new gasket, position inlet manifold to
cylinder head.
21.Fit nuts and bolts, tighten in the order shown to
the correct torque
25Nm
22.Position engine breather hose to manifold and
secure with bolts.
23.Connect fuel injector harness and intake air
temperature sensor multiplug.
24.Connect fuel hose to pressure regulator and
secure with clip.
25.Fit fuel pipe to fuel rail, tighten union to
10Nm
26.Connect vacuum hoses to manifold.
27.Position engine harness and cam cover brackets
to manifold, secure with bolts.
28.Connect breather hose and brake servo hose to
manifold, secure with clips.
29.Connect multiplug to fuel temperature sensor.
30.Connect breather hose to throttle housing and
secure with clip.
31.Connect throttle cable to cam and secure to
abutment bracket.
32.Connect coolant bypass hose to throttle housing.
33.Connect stepper motor and throttle
potentiometer multiplugs.
34.Connect air cleaner hose to throttle housing and
secure with clip.
35.Connect battery negative lead.
36.Adjust throttle cable.EXHAUST MANIFOLD GASKET - Mpi
Service repair no - 30.15.12
Remove
1.Raise vehicle.
2.Loosen 2 nuts securing downpipe to silencer
box.
3.Remove 4 nuts securing downpipe to exhaust
manifold.
4.Release downpipe from exhaust manifold.
5.Discard gasket.

30MANIFOLD AND EXHAUST SYSTEM
8
REPAIR 6.Disconnect oxygen sensor multiplug.
7.Release multiplug from bracket on thermostat
housing.
8.Release harness from cable tie.
9.Remove drive belt.
10.Remove 2 front bolts securing generator to
mounting bracket.
11.Remove 2 rear bolts securing generator to
mounting bracket.
12.Move generator from mounting bracket and
place aside.
13.Remove exhaust manifold heat shield.
14.Remove dipstick and bolt securing dipstick tube
to coolant rail.
15.Remove dipstick tube from cylinder block.16.Remove 3 bolts and 2 nuts securing exhaust
manifold to cylinder head.
17.Release coolant rail bracket from manifold studs.
18.Remove exhaust manifold and discard gasket.
Refit
NOTE: For torque values.See
Specifications, torque, Torque Values
19.Clean mating faces of exhaust manifold and
cylinder head.
20.Fit new manifold gasket and align exhaust
manifold to cylinder head.
21.Position coolant rail bracket to manifold studs.
22.Fit manifold nuts and bolts, tighten to the correct
torque in the order shown.
23.Secure oxygen sensor multiplug to bracket.
24.Connect oxygen sensor multiplug.
25.Fit new manifold flange gasket and align exhaust
front pipe to manifold.
26.Fit nuts and tighten diagonally to the correct
torque.
27.Tighten exhaust downpipe to silencer box nuts
to the correct torque.
28.Position generator to mounting bracket.
29.Fit and tighten 4 generator securing bolts.
30.Refit drive belt.