LAND ROVER DISCOVERY 1995 Workshop Manual
Manufacturer: LAND ROVER, Model Year: 1995, Model line: DISCOVERY, Model: LAND ROVER DISCOVERY 1995Pages: 873, PDF Size: 12.89 MB
Page 721 of 873

76CHASSIS AND BODY
54
REPAIR
5.Remove Torx screw securing seat belt.
6.Remove 2 Torx screws securing seat.
7.Disconnect multiplug.
8.Remove seat.
Refit
9.Reverse removal procedure.
10.Tighten Torx screws securing seat to
29 Nm (21
lbf ft)
.
11.Tighten bolts securing seat slides to
22 Nm (16
lbf ft)
.
12.Tighten Torx screw securing seat belt to
32 Nm
(24 lbf ft)
.FRONT SEAT - MANUAL - 5 DOOR (96 MODELS)
Service repair no - 76.70.01
Remove
1.Raise adjusting bar and slide seat fully
backwards.
2.Remove 2 bolts securing seat slides.
3.Raise adjusting bar and slide seat fully forwards.
4.Remove Torx screw securing seat belt.
5.Remove 2 Torx screws securing seat.
6.Remove seat.
Page 722 of 873

CHASSIS AND BODY
55
REPAIR Refit
7.Reverse removal procedure.
8.Tighten Torx screws securing seat to
29 Nm (21
lbf ft)
.
9.Tighten bolts securing seat slides to
22 Nm (16
lbf ft)
.
10.Tighten Torx screw securing seat belt to
32 Nm
(24 lbf ft)
.INTERIOR MIRROR (96 MODELS)
Service repair no - 76.10.51 - Manual
Service repair no - 76.10.54 - Auto dimming
Remove
NOTE: To remove manual mirror, follow
step 8 only.
1.Remove headlining front pocket.
2.Release left hand sun visor from clip and move
aside.
3.Release sun visor clip screw cover.
4.Remove clip securing screw and remove clip.
5.Remove 2 screws securing sunroof ECU and
move ECU aside.
6.Locate mirror multiplug, remove clip and
disconnect multiplug.
7.Remove tape securing harness (behind
headlining).
8.Release mirror from screen by applying sharp
downward pressure to the base.
CAUTION: Do not use tools to assist
removal. Mirror base should be moved in
direction of arrow, parallel to windscreen.
9.Release harness from behind headlining and
remove mirror.
Page 723 of 873

76CHASSIS AND BODY
56
REPAIR Refit
10.Reverse removal procedure. Ensure harness is
correctly routed in mirror base so it does not
become trapped.
Page 724 of 873

CHASSIS AND BODY
57
REPAIR SUN VISOR
Service repair no - 76.10.47
Remove
1.Release sun visor from headlining retaining clip.
2.Remove 3 screws securing sun visor to body.
3.Release sun visor and disconnect multiplug.
4.Remove sun visor.
Refit
5.Position sun visor and connect muliplug.
6.Position sun visor to headlining and secure with
screws.
7.Secure sun visor to headlining clip.WHEEL ARCH LINER - FRONT
Service repair no - 76.10.48
Remove
1.Raise front of vehicle and support on safety
stand.
2.Remove front road wheel.
3.Remove 4 wheel arch liner retainers.
4.Remove wheel arch liner.
Refit
5.Fit wheel arch liner and secure with retainers.
6.Fit front road wheel and tighten nuts to
126 Nm
(93 lbf ft)
.
7.Remove stand and lower vehicle.
Page 725 of 873

76CHASSIS AND BODY
58
REPAIR MUD FLAP - REAR - LH
Service repair no - 76.10.85
Remove
1.Remove rear compartment lower trim panel.
See rear compartment lower trim panel - lh -
with rear air conditioning fitted.
2.Remove 5 nuts and bolts securing mud flap to
body and bumper valance.
3.Remove mud flap.
Refit
4.Position mud flap to body, fit bolts and tighten
nuts to
10 Nm (7 lbf ft).
5.Fit rear compartment lower trim panel.
See rear
compartment lower trim panel - lh - with rear
air conditioning fitted.
REAR COMPARTMENT LOWER TRIM PANEL - LH
- WITH REAR AIR CONDITIONING FITTED
Service repair no - 76.13.03/20
Remove
1.Remove rear fold down seat.
See rear fold
down seats.
2.Remove fold down rear seat belts.See rear
fold down seat belts - lh - with rear air
conditioning fitted.
3.Remove 'E' post trim casing.See 'E' post trim
casing - lh - with rear air conditioning fitted.
4.Release load space cover end sleeve from
mounting bracket.
5.Remove load space cover.
6.Press rear seat squab release button and fold
squab forward.
7.Remove 2 screws securing load space cover
mounting bracket.
8.Remove mounting bracket.
Page 726 of 873

CHASSIS AND BODY
59
REPAIR
9.Remove 5 trim studs securing trim panel.
10.Remove trim panel.
Refit
11.Fit and align trim panel.
12.Fit trim panel retaining studs.
13.Position load space cover mounting bracket and
secure with screws.
14.Fold rear seat squab back and secure to latch.
15.Position load space cover to mounting brackets
and secure.
16.Fit 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
17.Fit fold down rear seat belts.See rear fold
down seat belts - lh - with rear air
conditioning fitted.
18.Fit rear fold down seat.See rear fold down
seats.
'E' POST TRIM CASING - RH
Service repair no - 76.13.13/03
Remove
1.Remove rear speaker.
See ELECTRICAL,
Repair, rear speaker.
2.Release 2 'E' post finisher retaining studs from
alpine light trim.
3.Release 2 'E' post finisher retaining clips from
lower trim panel.
4.Remove 'E' post finisher.
Refit
5.Position 'E' post finisher clips to lower trim panel.
6.Secure 'E' post finisher studs to alpine light trim.
7.Fit rear speaker.
See ELECTRICAL, Repair,
rear speaker.
Page 727 of 873

76CHASSIS AND BODY
60
REPAIR 'E' POST TRIM CASING - LH - WITH REAR AIR
CONDITIONING FITTED
Service repair no - 76.13.13/20
Remove
1.Remove rear speaker.
See ELECTRICAL,
Repair, rear speaker.
2.Release 2 trim casing retaining screw covers.
3.Remove 2 screws securing trim casing.
4.Remove trim casing.
Refit
5.Fit and align trim casing.
6.Fit and tighten screws securing trim casing and
fit covers.
7.Fit rear speaker.
See ELECTRICAL, Repair,
rear speaker.
ALPINE LIGHT TRIM CASING - LH - WITH REAR
AIR CONDITIONING FITTED
Service repair no - 76.13.20/20
Remove
1.Remove 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
2.Remove rear seat belt anchorage retaining bolt
cover.
3.Remove bolt securing rear seat belt anchorage.
4.Remove 2 trim studs securing trim casing.
5.Release trim casing from 2 retaining studs.
6.Remove trim casing.
Refit
7.Fit and align trim casing and secure with studs.
8.Fit 2 trim studs securing trim casing.
9.Position seat belt anchorage, fit bolt and tighten
to
20 Nm (15 lbf ft).
10.Fit cover to seat belt anchorage bolt.
11.Fit 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
Page 728 of 873

CHASSIS AND BODY
61
REPAIR REAR DOOR UPPER TRIM PANEL - WITH REAR
AIR CONDITIONING FITTED
Service repair no - 76.13.72/20
Remove
1.Remove alpine light trim casing.
See alpine
light trim casing - lh - with rear air
conditioning fitted.
2.Release 2 trim panel retaining screw covers.
3.Remove 2 trim panel retaining screws.
4.Release rear edge of trim panel from body.
5.Remove screw securing rear header duct to
alpine light duct.
6.Release rear header duct from alpine light duct.
7.Remove trim panel assembly.Dismantle
8.Remove 2 vents from trim panel.
9.Remove screw securing rear header duct to trim
panel.
10.Remove rear header duct.
Rebuild
11.Fit rear header duct to new trim panel and
secure with screw.
12.Fit vents to trim panel.
Refit
13.Position trim panel and connect rear header duct
to alpine light duct.
14.Fit and tighten screw securing rear header duct
to alpine light duct.
15.Secure rear edge of trim panel to body.
16.Fit and tighten screws securing trim panel.
17.Secure trim panel retaining screw covers.
18.Fit alpine light trim casing.
See alpine light
trim casing - lh - with rear air conditioning
fitted.
Page 729 of 873

76CHASSIS AND BODY
62
REPAIR 'D' POST TRIM CASING - LH - WITH REAR AIR
CONDITIONING FITTED - 5 DOOR
Service repair no - 76.13.73/20
Remove
1.Remove rear compartment lower trim panel.
See rear compartment lower trim panel - lh -
with rear air conditioning fitted.
2.Remove the squab release button from control
rod.
3.Release rear seat belt from guide and remove
guide.
4.Remove the trim casing retaining stud.
5.Release trim casing from 2 retaining studs.
6.Remove trim casing.
Refit
7.Fit trim casing under alpine light trim, align and
secure retaining studs.
8.Fit trim casing retaining stud.
9.Position trim casing rear edge beneath sixth light
seal flange.
10.Fit seat belt to guide, align squab release control
rod and position guide to trim casing.
11.Fit squab release button to control rod.
12.Fit rear compartment lower trim panel.
See rear
compartment lower trim panel - lh - with rear
air conditioning fitted.
Page 730 of 873

CHASSIS AND BODY
63
REPAIR SWITCH PACK - DASH PANEL CENTRAL LOUVRE
PANEL
Service repair no - 76.46.38
Remove
1.Release switch pack from louvre panel.
2.Disconnect 3 multiplugs from switch pack.
3.Remove switch pack.
Refit
4.Position switch pack.
5.Connect multiplugs to switch pack.
6.Secure switch pack to louvre panel.GRAB HANDLE
Service repair no - 76.58.30
Remove
1.Release 2 grab handle retaining screw covers.
2.Remove 4 screws securing grab handle to body.
3.Remove grab handle.
4.Collect 2 washers.
Refit
5.Position grab handle and washers.
6.Fit and tighten screws securing grab handle to
body.
7.Secure grab handle retaining screw covers.