LAND ROVER DISCOVERY 1995 Workshop Manual

ELECTRICAL
21
REPAIR INTERIOR LIGHT
Service repair no - 86.35.14
Remove
1.Pry out light unit from roof location.
2.Disconnect light switch plug.
Refit
3.Reverse removal procedure.
Bulb Removal.
1.Pry out interior light lens.
2.Remove bulb.
Refit
3.Reverse removal procedure.REAR LOADSPACE LIGHT
Service repair no - 86.41.40
Remove1.Pry light unit from trim panel.
2.Disconnect wiring leads.
3.Remove bulb.
Refit
4.Reverse removal procedure.

86ELECTRICAL
22
REPAIR SIDE REPEATER LIGHT
Service repair no - 86.50.59
Remove
1.Push the lens to the right and then pull outward
to detach lens and bulb holder from the panel.
2.Turn lens anti-clockwise and remove from bulb
holder.
3.Pull bulb from holder.
Refit
4.Reverse removal procedure.BUMPER MOUNTED SIDE LIGHT
Service repair no - 86.50.59
Remove
1.From behind bumper turn holder anti-clockwise
and release from light unit.
2.Pull bulb from holder.
Refit
3.Reverse removal procedure.

ELECTRICAL
23
REPAIR RADIO
Service repair no - 86.50.03
Remove
1.Disconnect battery earth lead.
2.Insert removal tools SMD 4091 to radio.
3.Release radio and remove tools.
4.Disconnect aerial and multiplugs from radio.
5.Remove radio.
Refit
6.Position radio, connect multiplugs and aerial,
and secure radio to fascia.
7.Connect battery earth lead.
8.Set radio code.SPEAKERS
Service repair no - 86.50.13
Door speakers
Remove
1.Remove the securing screws and withdraw the
speaker from the trim panel.
2.Disconnect the speakers leads.
Refit
3.Reverse removal procedure.

86ELECTRICAL
24
REPAIR SPEAKERS AND AMPLIFIER PACK, REAR DOOR
Service repair no - 86.50.36
Remove
1.Disconnect battery negative lead.
2.Remove securing screws and withdraw speaker
grille.
3.Remove securing screws and withdraw speaker
trim.
4.Remove securing screws ease speaker and
amplifier pack away from door panel, disconnect
multiplug and withdraw assembly.
5.Disconnect speaker plug from amplifier remove
securing screws and detach amplifier.Refit
6.Reverse removal procedure.

ELECTRICAL
25
REPAIR STARTER MOTOR - Mpi
Service repair no - 86.60.01
Remove
1.Disconnect battery negative lead.
2.Remove 2 nuts securing cables to starter
solenoid; release cables.
3.Remove 3 bolts securing starter motor.
4.Manoeuvre starter motor clear of bell housing.
5.Remove starter motor.Refit
6.Clean mating faces of starter motor and
differential housing.
7.Manoeuvre starter motor into position.
8.Fit mounting bolts and Tighten to
45 Nm.
9.Connect battery cables to starter solenoid; fit
nuts and tighten to the correct torque.
10.Reconnect battery negative lead.

86ELECTRICAL
26
REPAIR TRAILER SOCKET
Remove
1.If fitted remove the RH side facing seat
See
CHASSIS AND BODY, Repair, Rear Fold
Down Seats
2.Remove the rear lower side trim panelSee
CHASSIS AND BODY, Repair, Rear
Compartment Lower Trim Panels
3.Raise the carpet adjacent to the RH rear quarter
panel.
4.Disconnect the trailer socket lead multi-plug from
the RH body harness.
5.Displace the rubber grommet in the floor and
pass the socket lead through to the underside of
the vehicle.
6.Remove the securing screws and withdraw the
trailer socket from the towing hook mounting
bracket.
Refit
7.Reverse removal procedure.

ELECTRICAL
27
REPAIR WINDOW LIFT MOTOR - FRONT
Service repair no - 86.25.04
Remove
1.Ensure that the window glass is in its fully closed
position and secure it with adhesive tape.
2.Disconnect battery negative lead.
3.Remove the door pull, trim panel, and plastic
vapour barrier.
See CHASSIS AND BODY,
Repair, Front Door Trim Panel
4.Release the window lift motor wiring harness
from the three retaining clips to allow the
harness to be pulled out of the opening at the
front of the inner door panel.
5.Disconnect the window lift motor harness
multi-plug from the main door harness.
6.Support the motor, remove the three securing
bolts and withdraw the motor through the top
front opening of the door panel.
Refit
7.Reverse removal procedure.
NOTE: Ensure drive gear is engaged and
correctly aligned with window lift linkage
before fitting securing bolts.WINDOW LIFT MOTOR - REAR
Service repair no - 86.25.09
Remove
1.Ensure that the side door glass is in the fully
closed position and secure with adhesive tape.
2.Disconnect battery negative lead.
3.Remove the door pull, trim panel and plastic
vapour barrier.
See CHASSIS AND BODY,
Repair, Rear Side Door Trim - Panel
4.Disconnect the lift motor harness multi-plug from
the door harness.
5.Support the motor and remove the three
securing screws.
6.Withdraw the motor through the lower opening in
the inner door panel.
Refit
7.Reverse removal procedure.
NOTE: Ensure drive gear is engaged and
correctly aligned with window lift linkage,
before fitting securing bolts.

86ELECTRICAL
28
REPAIR INSTRUMENT PANEL FINISHER
Service repair no - 88.20.03
Remove
1.Position steering wheel for access.
2.Remove 2 screws securing panel.
3.Lift panel clear, disconnect multiplug
connections.
Refit
4.Reverse removal procedure.

ELECTRICAL
29
REPAIR INSTRUMENT BINNACLE
Service repair no - 88.20.13
Remove
1.Remove instrument panel finisher.
See
Instrument panel finisher
2.Remove 4 screws securing binnacle to fascia.
3.Carefully ease 2 lower panel finisher brackets
downwards.
4.Withdraw binnacle to gain access to multiplugs.
5.Noting their fitted positions, disconnect
multiplugs.
6.Remove binnacle.
Refit
7.Reverse removal procedure.

86ELECTRICAL
30
REPAIR INSTRUMENT ILLUMINATION AND WARNING
LIGHT BULBS
Service repair no - 86.45.48 - Instrument
Service repair no - 86.45.61 - Warning light
Remove
1.Remove binnacle.
See Instrument binnacle
2.Identify bulb to be replaced.
NOTE: If faulty bulb is not accessible,
remove screws securing circuit board and
carefully ease circuit board aside.
3.Rotate bulb holder anti-clockwise, withdraw bulb
holder and remove bulb.Refit
4.Fit new bulb to holder.
CAUTION: Ensure bulb of correct wattage
and type is fitted.
5.Reverse removal procedure.