oil LAND ROVER DISCOVERY 2002 Workshop Manual

ENGINE - TD5
OVERHAUL 12-1-85
4.Apply a bead of sealant, Part No. STC 3254 to
joint faces of timing chain cover and crankshaft
rear oil seal housing.
CAUTION: Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.
5.Position new sump gasket.
CAUTION: Gasket must be fitted dry.
6.Position sump, fit and lightly tighten bolts
ensuring they are in their original fitted
positions.
7.Using sequence shown, tighten sump bolts to
25 Nm (18 lbf.ft).8.Fit new centrifuge oil drain pipe gasket.
CAUTION: Gasket must be fitted dry.
9.Fit centrifuge oil drain pipe, fit bolts and tighten
to 10 Nm (7 lbf.ft).

ENGINE - TD5
12-1-86 OVERHAUL
Seal - crankshaft - rear - manual models
$% 12.21.20.01
Disassembly
1.Remove flywheel.

+ ENGINE - Td5, OVERHAUL,
Flywheel.
2.Remove sump gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- engine sump.
3.Remove 5 bolts securing crankshaft rear oil
seal housing to cylinder block.
4.Release crankshaft rear oil seal housing from
locating dowels, discard rear oil seal and
housing.
Reassembly
1.Clean crankshaft oil seal housing mating face
on cylinder block, ensure bolt and dowel holes
are clean and dry. Remove all traces of oil from
oil seal running surface on crankshaft.
2.Position seal protector LRT-12-061 over
crankshaft boss. Fit new oil seal and housing
and remove tool LRT-12-061.
CAUTION: Oil seal must be fitted dry.3.Fit oil seal housing bolts and using sequence
shown, tighten to 9 Nm (7 lbf.ft).
4.Fit sump gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- engine sump.
5.Fit flywheel.

+ ENGINE - Td5, OVERHAUL,
Flywheel.

ENGINE - TD5
OVERHAUL 12-1-87
Seal - crankshaft - rear - automatic
models
$% 12.21.20.01
Disassembly
1.Remove sump gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- engine sump.
2.Remove drive plate.

+ ENGINE - Td5, OVERHAUL, Drive
plate.
3.Remove 5 bolts securing crankshaft rear oil
seal housing to cylinder block.
4.Release crankshaft rear oil seal housing from
locating dowels, discard rear oil seal and
housing.
Reassembly
1.Clean crankshaft oil seal housing mating face
on cylinder block, ensure bolt and dowel holes
are clean and dry. Remove all traces of oil from
oil seal running surface on crankshaft.2.Position seal protector LRT-12-061 over
crankshaft boss. Fit new oil seal and housing
and remove tool LRT-12-061.
CAUTION: Oil seal must be fitted dry.
3.Fit oil seal housing bolts and using sequence
shown, tighten to 9 Nm (7 lbf.ft).
4.Fit sump gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- engine sump.
5.Fit drive plate.

+ ENGINE - Td5, OVERHAUL, Drive
plate.

ENGINE - TD5
12-1-90 OVERHAUL
Pump - oil
$% 12.60.26.02
Disassembly
1.Remove sump gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- engine sump.
2.Remove bolt securing oil pump drive sprocket.
3.Release drive sprocket from chain, remove
sprocket.
4.Remove 3 Torx screws securing oil pick-up
strainer, remove strainer.
5.Remove and discard 'O' ring.6.Using sequence shown, remove and discard 22
bolts securing oil pump and stiffener plate
assembly to cylinder block.
7.Release stiffener plate from locating dowels,
remove oil pump and stiffener plate assembly.
8.Remove and discard 'O' ring from oil pump
housing outlet.
Inspection
1. Inspection/overhaul procedures for the oil
pump are limited to carrying out
dimensional checks. In the event of wear or
damage being found, a replacement pump
and stiffener plate assembly must be fitted.

ENGINE - TD5
OVERHAUL 12-1-91
2.Remove and discard 5 screws securing cover
to oil pump, remove cover.
3.Using a felt tipped pen, make suitable
alignment marks between inner and outer
rotors and oil pump body.
4.Remove inner and outer rotors.
5.Check rotors and pump body for signs of
scoring and wear.
6.Fit rotors ensuring that marks are aligned and
identification mark on inner rotor is facing
outwards.7.Using feeler gauges, check pump outer rotor to
body clearance:
lOuter rotor to body clearance = 0.295 to
0.375 mm (0.012 to 0.015 in)
8.Using feeler gauges, check clearance of inner
to outer rotor in 2 positions; both clearances
must be within limit given:
lInner to outer rotor clearance = 0.13 mm
(0.05 in)

ENGINE - TD5
12-1-92 OVERHAUL
9.Place a straight edge across pump body and
using feeler gauges, measure end-float of
outer rotor:
lOuter rotor end-float = 0.038 to 0.075 mm
(0.0001 to 0.003 in)
10.Check drive shaft bush in pump cover for signs
of scoring and wear.
11.Renew oil pump and stiffener plate assembly if
excessive scoring or wear exists.
12.Lubricate pump rotors and drive shaft bush with
engine oil.
13.Fit rotors ensuring reference marks are aligned
and identification mark on outer rotor is facing
outwards.
14.Fit cover to pump, fit 5 new screws and tighten
by diagonal selection to 6 Nm (4.5 lbf.ft).
15.Remove and discard oil pressure relief valve
plug.
16.Remove spring and relief valve plunger.
17.Clean valve plunger and spring.
18.Check valve plunger and relief valve bore for
scoring and corrosion, light scoring and
corrosion may be removed using grade 600
emery cloth soaked in oil.19.Check spring for distortion, check free length of
spring:
lSpring free length = 42.0 mm (1.65 in)
20.Lubricate valve plunger and seating.
21.Fit valve plunger and spring to oil pump.
22.Apply Loctite 243 sealant to threads of a new
plug. Do not attempt to fit original plug.
23.Fit plug and tighten to 23 Nm (17 lbf.ft).
Reassembly
1.Clean mating faces of oil pump, stiffener plate
assembly and cylinder block; ensure bolt and
dowel holes are clean and dry.
2.Lubricate a new 'O' ring with engine oil and fit to
oil pump housing outlet.
3.Position oil pump and stiffener plate assembly
on to cylinder block ensuring 2 dowels are
correctly located.
4.Fit new bolts and using sequence shown,
tighten to 13 Nm (10 lbf.ft).
5.Lubricate a new 'O' ring with engine oil and fit to
oil pick-up strainer.
6.Clean threads of oil pick-up strainer Torx
screws and apply Loctite 242 to screw
threads.
7.Fit oil pick-up strainer, fit Torx screws and
tighten to 10 Nm (8 lbf.ft).
8.Position oil pump drive sprocket to chain and oil
pump ensuring that the 'D' shape on the drive
sprocket is located on the flat on the oil pump
drive shaft.
9.Clean oil pump drive sprocket retaining bolt and
apply Loctite 242 to bolt threads.
10.Fit oil pump drive sprocket and tighten bolt to
25 Nm (18 lbf.ft).
11.Fit new sump gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- engine sump.

ENGINE - TD5
OVERHAUL 12-1-93
Timing chain and sprockets
$% 12.65.13.01
Disassembly
1.Remove cylinder head gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- cylinder head.
CAUTION: If timing chain tensioner is to be
replaced, ensure tensioner is correct for
engine. Tensioner bodies are colour coded
as follows: Engine Serial No. Prefixes 10P to
14P – BLACK with, additionally on later
engines, YELLOW on tensioner hex. head.
Serial No. Prefixes 15P to 19P – body is
colour coded YELLOW. Later tensioners
may be fitted to early engines provided that
the modified adjustable guide is also fitted.
2.Remove 3 bolts securing damper to crankshaft
pulley, remove damper.
3.Fit LRT-51-003 to crankshaft pulley.
4.Secure tool using 2 bolts.
5.Using assistance, restrain engine and remove
crankshaft pulley bolt; discard bolt.
WARNING: CRANKSHAFT BOLT IS
TIGHTENED TO 460 Nm (340 lbf.ft), ENSURE
ENGINE IS ADEQUATELY RESTRAINED.
6.Remove crankshaft pulley.7.Remove sump gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- engine sump.
8.Noting their fitted position, remove 8 bolts
securing timing chain cover.
9.Release timing chain cover from locating
dowels, remove cover.
10.Remove bolt securing oil pump drive sprocket.
11.Remove oil pump drive sprocket.
12.Remove camshaft and crankshaft sprockets
together with timing and oil pump drive chains.
13.Remove Woodruff key from crankshaft.
14.Remove 2 bolts and remove timing chain fixed
guide.

ENGINE - TD5
12-1-94 OVERHAUL
15.Remove bolt and remove timing chain
adjustable guide.
16.Remove bolt and remove timing chain
lubrication jet.
17.Using tool LRT-12-092, remove and discard oil
seal from timing cover.
Inspection
1.Clean all components.
2.Check condition of timing chain running
surfaces on adjustable and fixed guides.
CAUTION: Adjustable guide fitted to Engine
Serial No. Prefixes 15P to 19P may be fitted
to early engines provided that timing chain
tensioner having a YELLOW coloured body
is also fitted.
3.Check timing chains and sprockets for signs of
wear.
CAUTION: Timing chains and sprockets
fitted to Engine Serial No. Prefixes 15P to
19P may be fitted to early engines as an
assembly only, oil pump drive sprockets are
interchangeable. Later timing chains have
BRONZE coloured timing links.
4.Check that drilling in timing chain lubrication jet
is clear.
5.Clean oil seal recess in timing cover and oil seal
running surface on crankshaft.
6.Remove all traces of sealant from mating faces
of timing cover and cylinder block using
suitable solvent.
CAUTION: Do not use metal scrapers.
7.Ensure bolt and dowel holes are clean and dry.
8.Clean oil pump sprocket bolt threads.Reassembly
1.Fit timing chain lubrication jet.
2.Fit timing chain lubrication jet Torx screw and
tighten to 10 Nm (7 lbf.ft).
3.If crankshaft has been rotated, check that No.1
piston is at TDC using the following
procedures:
4.Temporarily fit and lightly tighten a new
crankshaft pulley bolt.
5.Assemble a magnetic base DTI to cylinder
block top face, position stylus to cylinder block
face and zero gauge.
6.Using crankshaft pulley bolt, rotate crankshaft
clockwise until No.1 piston is at top of its stroke
and woodruff key slot in crankshaft is at 12
o'clock position.
7.Position stylus of DTI to No.1 piston crown and
rotate crankshaft until highest reading is
indicated on DTI.
8.Check that Woodruff key slot is still at 12
o'clock position indicating No.1 piston is at
TDC firing.
9.Remove DTI.
10.Remove and retain crankshaft pulley bolt.
11.Fit Woodruff key to crankshaft.
12.Fit oil pump drive chain to rear row of teeth on
crankshaft sprocket - i.e. teeth furthest away
from timing mark on sprocket.
13.Fit sprocket to crankshaft ensuring that timing
mark on sprocket is facing towards front end of
crankshaft.
14.Fit oil pump drive sprocket to oil pump and drive
chain ensuring that 'D' shape on sprocket is
located on flat on oil pump drive shaft.

ENGINE - TD5
OVERHAUL 12-1-95
15.Apply Loctite 242 to threads of oil pump drive
sprocket bolt, fit bolt and tighten to 25 Nm (18
lbf.ft).
16.Fit timing chain fixed guide, fit bolts and tighten
to:
l M6 bolt – 10 Nm (7 lbf.ft)
lM10 bolt – 45 Nm (34 lbf.ft)
17.Fit timing chain adjustable guide, fit bolt and
tighten to 25 Nm (18 lbf.ft).
18.Fit camshaft sprocket to timing chain with
timing mark on sprocket between the 2
coloured links, suitably retain sprocket on
chain.
19.Fit timing chain to crankshaft sprocket aligning
coloured link to timing mark on sprocket.
20.Ensure timing marks are positioned as shown -
No.1 piston at TDC firing.
21.Apply an even film of sealant Part No. STC
4600 to mating face of timing cover and
spread to an even film using a roller.
CAUTION: Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.22.Fit timing cover, fit bolts in their original fitted
positions and working from the centre
outwards, tighten progressively to 27 Nm (20
lbf.ft).
23.Fit oil seal guide, from seal kit over end of
crankshaft.
24.Fit new oil seal into timing cover using tool
LRT-12-156.
CAUTION: Oil seal must be fitted dry.
25.Remove tool LRT-12-156 and oil seal guide.
26.Fit crankshaft pulley, fit and lightly tighten
crankshaft pulley bolt.

ENGINE - TD5
12-1-96 OVERHAUL
27.Fit tool LRT-51-003 to crankshaft pulley,
secure with 2 bolts. Using assistance, restrain
engine and using a torque multiplier tighten
bolt to 450 Nm (340 lbf.ft).
WARNING: DUE TO THE HIGH TORQUE
LOADING REQUIRED, IT IS ESSENTIAL
THAT ENGINE IS ADEQUATELY
RESTRAINED.
28.Remove tool LRT-51-003.
29.Position damper to crankshaft pulley, fit 3 bolts
and tighten to 80 Nm (60 lbf.ft).
30.Fit sump gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- engine sump.
31.Fit cylinder head gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- cylinder head.
Bearings - connecting rods
$% 12.17.16.01
Disassembly
1.Remove oil pump.

+ ENGINE - Td5, OVERHAUL, Pump -
oil.
2.Mark cylinder reference number on each
connecting rod big-end bearing cap.
3.Make suitable alignment marks between each
big-end bearing cap and connecting rod.
CAUTION: Due to the 'fracture split' method
of manufacturing connecting rods,
incorrect fitment of cap to rod will damage
mating faces and necessitate replacement
of connecting rod assembly.
4.Rotate crankshaft clockwise until No.1 big-end
is at BDC.
5.Remove and discard 2 bolts securing each
connecting rod big-end bearing cap.
6.Remove bearing cap, remove and discard big-
end bearing shell.
7.Push connecting rod up cylinder bore until
connecting rod is clear of crankshaft journals.
CAUTION: Ensure that connecting rod does
not contact cylinder bore or oil squirt jet and
piston does not contact the valves or EUI's
if the cylinder head is fitted.