lock LAND ROVER DISCOVERY 2002 Manual PDF

ENGINE - TD5
DESCRIPTION AND OPERATION 12-1-29
Lubrication circuit
Cylinder block flow
1Oil squirt jets (5 off)
2Main oil delivery gallery
3Inflow from oil cooler housing
4Flow to oil cooler / filters (from oil pump via
cylinder block)
5Sump
6Oil pick-up pipe
7Flow from oil pump (relief-valve in housing)
8Oil pump9Cross-drilling supply to main and crankshaft
bearings
10To cylinder head

ENGINE - TD5
12-1-30 DESCRIPTION AND OPERATION
Oil from the sump is drawn up through a two-piece plastic pick-up which contains a mesh to siphon any relatively large
pieces of material which could cause damage to the pump. The head of the pick-up is centrally immersed in the sump
oil and oil is delivered to the inlet side of the eccentric rotor pump through a gallery in the stiffener plate.
Pressurised oil from the pump is passed through to the cylinder block where it is delivered to the centrifuge filter and
full-flow filter via a port in the RH cylinder block which interfaces with a port in the centre gallery of the oil cooler
housing. The oil pump contains an oil pressure relief valve which opens to allow oil to be recirculated back around the
pump if the oil pressure increases to a high enough level.
10% of the oil flow from the pump is diverted through the centrifuge filter and returned to the sump via the centrifuge
filter drain tube. The remaining 90% of the oil passes through the standard full-flow filter to the main oil gallery in the
cylinder block.

ENGINE - TD5
DESCRIPTION AND OPERATION 12-1-31
Oil cooler / Filter flow (thermostat open)
1To cylinder block main gallery (from rear of oil
cooler housing)
2Oil cooler housing
3Oil pressure switch
4Full-flow filter
5Centrifuge filter6Return to sump
7Flow from oil pump (via cylinder block)
8Oil cooler matrix

ENGINE - TD5
12-1-32 DESCRIPTION AND OPERATION
When the engine temperature is below 74° C, the thermostat in the full-flow filter housing is closed and a proportion
of the oil flow to the main oil gallery is diverted to the oil cooler to supply an oil feed to the turbocharger bearings. Oil
passes through the oil cooler to the front gallery in the oil cooler housing where there is a tapping to connect the feed
pipe to the turbocharger. Oil used by the turbocharger bearings is returned to the sump through an oil drain pipe which
connects to a port in the LH side of the cylinder block.
The remainder of the oil flow leaving the full-flow filter outlet is passed into the cylinder block via a port at the rear of
oil cooler rear gallery.
When the oil temperature rises above 74
° C the thermostat in the full-flow filter adaptor housing begins to open to
allow a proportion of the oil from the full-flow filter to pass through the oil cooler before it reaches the main oil gallery
in the cylinder block. In this instance, oil supply to the turbocharger bearings is fed directly from the full-flow filter
without first passing through the oil cooler. Between 74
° C and 88° C the thermostat valve plunger opens by about
9mm to allow proportionally more oil to flow through the oil cooler before being passed to the cylinder block main oil
delivery gallery. Above 88
°C the thermostat valve continues to open by about 1mm for every 10° C increase in
temperature until the valve is fully open, when all the oil flow to the cylinder block is forced to pass to the cylinder block
via the oil cooler.
An oil pressure switch is located in a port in the rear gallery of the oil cooler housing to sense the oil pressure level
before flow enters the main oil gallery in the engine block. A warning lamp in the instrument cluster is switched on if
the oil pressure is detected as being too low.

+ INSTRUMENTS, DESCRIPTION AND OPERATION, Description.
Drillings from the cylinder block main oil gallery direct oil to the crankshaft main bearings and cross drillings in the
crankshaft direct oil to the big-end bearings. An additional five drillings in the cylinder block supply oil at reduced
pressure to the oil squirt jets for piston cooling and gudgeon pin lubrication.
Oil supply from the cylinder block is then passed to the cylinder head galleries through a non-return valve which is
included as an integral item in the lower face of the cylinder head.

ENGINE - TD5
DESCRIPTION AND OPERATION 12-1-33
Cylinder head flow
1Cast-in groove between cylinder head and
camshaft carrier
2Rocker shaft flow
3Lash adjuster supply channels (10 off)
4Non-return valve
5Chain lubrication jet supply6Oil return from vacuum pump
7Oil supply to timing chain tensioner adjuster
8Oil supply to vacuum pump
9Oil supply hole to camshaft sprocket and timing
chain
Oil passes to the cylinder head from the cylinder block via a non-return valve which is included to prevent oil draining
away from the lash adjusters when the engine is switched off.
Oil is passed to a cast-in groove between the top of the cylinder head and the camshaft carrier. The part of the channel
on the top left hand side of the cylinder head has ten cross-drillings which supply oil to the hydraulic lash adjusters
and finger followers. Lubrication oil fed to the lash adjusters passes up through the lash adjuster body and into the
socket of the finger followers. The oil exits the finger followers through a small hole to lubricate the surfaces between
the camshaft lobes and rollers.
An additional tapping is included at the front left hand side of the cylinder head to supply oil to the chain lubrication
jet, and a through hole near the front centre of the cylinder head allows a passage of oil through from the cast-in
groove to lubricate the timing chain and camshaft sprocket.
At the centre front of the cylinder head, the cast-in groove channels oil into the rockershaft via the front rockershaft
fixing. Oil flow through the rockershaft and clearance around the rockershaft fixings provides oil feed to the camshaft
bearings.

ENGINE - TD5
12-1-38 REPAIRS
Seal - crankshaft - rear
$% 12.21.20
Remove
1. Automatic models: Remove drive plate

+ ENGINE - Td5, REPAIRS, Plate -
drive - automatic.
2. Manual models: Remove flywheel.

+ ENGINE - Td5, REPAIRS, Flywheel.
3.Remove sump gasket.

+ ENGINE - Td5, REPAIRS, Gasket -
sump.
4.Remove 5 bolts securing crankshaft oil seal
housing to cylinder block.
5.Remove crankshaft oil seal housing.
Refit
1.Clean interface between crankshaft oil seal
housing and cylinder block.
2.Position seal protector, LRT-12-061 over
crankshaft boss. Fit new seal and remove tool
LRT-12-061 .
CAUTION: Oil seal must be fitted dry.3.Fit crankshaft rear oil seal housing bolts and
using sequence shown, tighten to 9 Nm (7
lbf.ft).
4.Fit new sump gasket.

+ ENGINE - Td5, REPAIRS, Gasket -
sump.
5. Automatic models: Fit drive plate

+ ENGINE - Td5, REPAIRS, Plate -
drive - automatic.
6. Manual models: Fit flywheel.

+ ENGINE - Td5, REPAIRS, Flywheel.

ENGINE - TD5
12-1-40 REPAIRS
13.Disconnect 4 glow plug connectors.
14.Disconnect MAP sensor multiplug from inlet
manifold.
15.Position engine harness clear of inlet manifold.
16.Disconnect vacuum hose from EGR valve.
17.Release 3 clips and disconnect coolant hoses
from fuel cooler.
18.Disconnect fuel hoses, tank to fuel cooler and
connector block on cylinder head.
CAUTION: Always fit plugs to open
connections to prevent contamination.19.Disconnect fuel hose from connector block on
cylinder head.
20.Disconnect fuel hose from fuel cooler and
secure to connector block on cylinder head.
This is to prevent contamination of the fuel
injection system.
Pre EU3 model shown
21.Loosen clip screw and disconnect air intake
hose from EGR valve.
22.Loosen vacuum pump oil feed pipe union from
cylinder head and discard 'O' ring.
23.Loosen 2 bolts and release alternator support
bracket from cylinder head.
24. Pre EU3 model: Remove bolt securing EGR
valve pipe clamp to cylinder head.
25. EU3 model: Release the clips and disconnect
the coolant hoses from the EGR cooler.
26.Remove nut and bolt securing cylinder head to
timing chain cover.
27.Release clips and disconnect top hose, heater
hose and heater feed hose.
28.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.

ENGINE - TD5
REPAIRS 12-1-41
29.Rotate engine clockwise to align mark on
camshaft sprocket between coloured links on
timing chain.
30.Position tool LRT-12-058 through camshaft
carrier to lock camshaft.
31.Position tool LRT-12-158 through gearbox bell
housing to lock crankshaft. 32.Remove timing chain tensioner and discard
sealing washer.
33.Remove timing chain fixed guide Allen screw
from front of cylinder head.
34.Lever out camshaft sprocket blanking plug and
'O'-ring seal from front of cylinder head and
discard.
35.Remove 3 bolts and release timing sprocket
from camshaft. Discard bolts.
36.Using sequence shown, progressively loosen
then remove and discard 12 cylinder head bolts
together with their captive washers.

ENGINE - TD5
12-1-42 REPAIRS
37.Using suitable lifting chains and tool LRT-12-
138 carefully remove cylinder head and place
on wooden blocks or stands.
CAUTION: Support both ends of cylinder
head on blocks of wood. With the camshaft
carrier bolted down, the injector nozzles
and some of the valves will protrude from
the face of the cylinder head.
38.Remove cylinder head gasket.
39.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of cylinder head.
40.Remove and discard plastic dowels from
cylinder block.Refit
1.Clean mating faces of cylinder head and
cylinder block.
2.Check cylinder head for warping, across centre
and from corner to corner: – Maximum warp =
0.10 mm (0.0004 in)
CAUTION: Cylinder heads may not be
refaced, replace cylinder head if warping
exceeds figure given.
3.Ensure coolant and oil passages are clean.
4.Clean dowel holes and fit new plastic dowels.
5.Lightly lubricate threads and beneath heads of
cylinder head bolts with clean engine oil.
6.Fit new cylinder head gasket of the correct
thickness with the word 'TOP' uppermost.
7.Using assistance, fit cylinder head and locate
onto dowels.
8.Carefully enter cylinder head bolts, DO NOT
DROP. Lightly tighten bolts.
9.Using the sequence shown, progressively
tighten cylinder head bolts to 30 Nm (22 lbf.ft),
then to 65 Nm (48 lbf.ft), then a further 90
°, then
a further 180
° and finally a further 45°.
CAUTION: Ensure correct sequence is
followed for all 5 tightening stages. Do not
tighten bolts 315 degrees in one operation.
10.Fit nut and bolt securing cylinder head to timing
chain cover and tighten to 25 Nm (18 lbf.ft).

ENGINE - TD5
REPAIRS 12-1-43
11.Clean camshaft sprocket and mating face on
camshaft.
12.Ensure engine is set to TDC No. 1 cylinder and
mark on camshaft sprocket is positioned
between the 2 coloured links.
13.Position camshaft sprocket to camshaft; fit and
lightly tighten new bolts, then loosen bolts half
a turn.
14.Clean timing chain fixed guide retaining pin and
apply Loctite 242 to threads.
15.Fit timing chain fixed guide retaining pin and
tighten to 25 Nm (18 lbf.ft) .
16.Clean timing chain tensioner and fit new
sealing washer.
17.Fit timing chain tensioner and tighten to 45 Nm
(22 lbf.ft).
18.Tighten bolts securing camshaft sprocket to
camshaft to 37 Nm (27 lbf.ft).
19.Remove tool LRT-12-058 from camshaft.
20.Remove tool LRT-12-158 from gearbox bell
housing.
21.Fit new camshaft bore blanking plug and 'O'-
ring seal in recess in cylinder head.
22.Clean vacuum pump union.
23.Tighten union securing vacuum pump oil feed
pipe to cylinder head to 10 Nm (7 lbf.ft) .
24.Fit bolts securing alternator support bracket to
cylinder head and tighten to 25 Nm (18 lbf.ft) .
25.Connect top hose and heater hoses and secure
with clips.
26. Pre EU3 model:Fit bolt securing EGR pipe
clamp to cylinder head bolt and tighten to 10
Nm (7 lbf.ft) .
27. EU3 model: Connect coolant hoses to EGR
cooler and secure with the clips.
28.Position air intake hose to EGR valve and
tighten clip screw.
29.Disconnect fuel hose from connector block and
connect to fuel cooler.
30.Connect fuel hoses to fuel cooler and
connector block on cylinder head.
31.Connect coolant hoses to fuel cooler and
secure clips.
32.Connect vacuum hose to EGR valve.
33.Position engine harness and connect multi
plugs and glow plug connectors.
34.Fit and tighten bolts, engine harness to
camshaft carrier.
35.Clean exhaust manifold and turbocharger
interface.
36.Fit new gasket to exhaust manifold, position
turbocharger and tighten – nuts securing
turbocharger to manifold to 30 Nm (22 lbf.ft).
37.Clean turbocharger oil feed hose bolt.
38.Position turbocharger oil feed hose using new
sealing washers. Fit banjo bolt securing
turbocharger oil feed hose and tighten to 25 Nm
(18 lbf.ft) . 39.Position exhaust manifold heatshield and
tighten M6 bolts to 9 Nm (7 lbf.ft) and M8 bolt to
25 Nm (18 lbf.ft).
40.Fit cooling fan coupling.

+ COOLING SYSTEM - Td5, REPAIRS,
Fan - viscous.
41.Fit camshaft cover with new seal.

+ ENGINE - Td5, REPAIRS, Gasket -
cover - camshaft.
42.Refill cooling system.

+ COOLING SYSTEM - Td5,
ADJUSTMENTS, Drain and refill.
43.Connect battery earth lead.
44.Fit battery cover and secure fixings.
45.Fit bonnet.

+ EXTERIOR FITTINGS, REPAIRS,
Bonnet.