bonnet LAND ROVER FREELANDER 2001 User Guide

MAINTENANCE
10-2 MAINTENANCE
K1.8 – Petrol Engine – Under Bonnet
View
LHD shown, RHD similar
1Cooling system expansion tank filler cap
2Engine oil dipstick
3Brake/Clutch fluid reservoir cap
4Engine Control Module box
5Engine compartment fusebox
6Battery
7Air cleaner
8Engine oil filler cap
9Windscreen washer reservoir filler cap
10Power steering reservoir

MAINTENANCE
MAINTENANCE 10-3
KV6 – Petrol Engine – Under Bonnet
View
LHD shown, RHD similar - 03 Model Year illustrated
1Power steering reservoir
2Cooling system expansion tank filler cap
3Brake/Clutch fluid reservoir cap
4Engine Control Module box
5Engine compartment fusebox
6Battery
7Engine oil filler cap
8Engine oil dipstick
9Windscreen washer reservoir filler cap

MAINTENANCE
MAINTENANCE 10-11
Door Locks, Hinges, Check Straps and
Bonnet Catch
Check
1.Check operation of each door, door lock,
bonnet catch and fuel filler flap.Lubricate Front and Rear Doors
1.Open each door in turn and lubricate door
hinges and check strap using recommended
lubricant.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
2.Lubricate door lock, striker and private lock
using PTFE lubricant. Remove excessive
lubricant, particularly from door striker area, to
avoid customer complaint.
3.Check tightness of accessible door lock and
striker fixings.
4.Open and close door to check for smooth,
noise-free operation. Ensure door closes
securely.
5.Check for smooth operation of private lock.
Lubricate Tail Door
1.Open tail door and lubricate hinges using
recommended lubricant.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
2.Grease tail door check slide.
3.Lubricate rear door lock and striker using PTFE
lubricant. Remove excessive lubricant to avoid
customer complaint, particularly from door
striker area.
4.Check tightness of accessible tail door lock and
striker fixings.
Lubricate Bonnet
1.With bonnet open, lubricate hinges, striker, lock
and safety catch using a suitable lubricant.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
Sunroof Guide Rails, Slides and Seal
1.With sunroof open, lubricate accessible guide
rails, slides and seals. Remove any excess
lubricant to avoid contaminating roof lining and
trim.
2.Ensure sunroof closes correctly.
Sunroof Drain Tubes and Channels
1.Remove any debris from sunroof tray.
2.Ensure that all accessible sunroof drain tubes
are clear using a low pressure air line.

MAINTENANCE
MAINTENANCE 10-29
Gear Change and Parking Pawl Engagement –
(Automatic only, normal driving conditions)
1.Select 'R' and check for smooth take up.
2.Select 'D' and check for smooth up-changes of
ratio from rest.
3.Slow down vehicle and check for smooth down-
changes of ratio.
4.Stop vehicle on a slope.
5.Select 'P' and release handbrake.
6.Check that vehicle does not move and that
selector does not slip out of 'P'.
7.Carry out a similar check with vehicle facing in
the opposite direction.
Steering
1.With vehicle stationary, turn steering from lock
to lock. Check for smooth operation and ensure
there is no undue noise from the power steering
pump or drive belt.
Suspension
1.Check for noise, irregularity in ride (e.g.
dampers) and wheel imbalance.
Foot brake
1.Check for pedal effort, travel, braking
efficiency, pulling and binding.
Handbrake
1.Apply handbrake firmly, check travel and
ratchet hold and release.
Instruments
1.Check for correct operation of all instruments
and warning devices where practical.
Body
1.Check for abnormal body noise.
Seat Belts
1.Check for operation of inertia reels.Road Test
1.Drive vehicle on a short road test. Check all
vehicle systems for correct operation. Pay
particular attention to:
lEngine noise
lGearbox noise
lSuspension noise
lBody noise
lBraking system operation
lGear selection
lEngine performance
2.Where possible, check for correct operation of
Hill Descent Control (HDC) system. This should
not be carried out if excessive journey time is
required.
3.After road test, carry out a final inspection of the
vehicle on vehicle ramps.
4.Check all underbonnet fluid levels and top-up if
necessary.

ENGINE - K SERIES KV6
REPAIRS 12-3-25
Cover - engine acoustic
$% 12.30.50
Remove
1.Loosen clip and disconnect fresh air intake
hose from acoustic cover.
2. Non NAS: Loosen clip and release air intake
and air bypass hose from throttle body.
3. NAS:Loosen clip and disconnect air intake
hose from air flow meter (MAF) sensor.
4.Release 2 turnbuckles securing acoustic cover
to LH camshaft cover.
5.Release retaining strap and remove acoustic
cover.
Refit
1.Fit and secure engine acoustic cover.
2.Connect air intake and air bypass hoses,
secure clip.
3.Connect fresh air intake hose to acoustic cover
and tighten clip screw.
Engine and automatic gearbox - up to
03MY
$% 12.37.01.99
Remove
1.Disconnect battery earth lead.
2.Tie bonnet back in upright position.
3.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
4.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
5.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
6.Remove engine ECM.

+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - Non NAS.
7.Remove 2 screws securing harness clamp and
remove clamp.
8.Disconnect 2 engine harness to main harness
multiplugs.

ENGINE - K SERIES KV6
12-3-34 REPAIRS
38.With assistant depressing the brake pedal,
tighten front hub nuts to 400 Nm (295 lbf.ft).
39.Stake nut to shaft.
40.Fit front road wheels, fit and tighten nuts to 115
Nm (85 lbf.ft).
41.Lower vehicle on ramp.
42.Connect brake servo vacuum hose to inlet
manifold chamber.
43.Connect coolant hose to underside of
expansion tank and secure with clip.
44.Connect expansion tank hose to inlet manifold
and secure clip.
45.Connect top hose to radiator and secure with
clip. Position hose in bracket.
46.Connect heater feed and return hoses and
secure with clips.
47.Connect throttle inner cable to throttle cam and
secure outer cable in abutment bracket, if fitted.
48.Secure throttle cable in clips on harness
brackets, if fitted.
49.Adjust throttle cable, if fitted.

+ FUEL DELIVERY SYSTEM -
PETROL, ADJUSTMENTS, Throttle cable -
check and adjust - KV6.
50.Connect hose to purge control valve.
51.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
52.Connect gearbox harness multiplugs and
secure multiplugs in mounting bracket clips.
53.Connect Lucar connector to starter solenoid.
54.Position earth lead to gearbox housing, fit and
tighten bolt to 25 Nm (18 lbf.ft).
55.Position engine harness to 'E' box mounting
bracket and secure with clips.
56.Connect earth header multiplug.
57.Connect multiplug to underbonnet fuse box.
58.Position battery and starter motor lead to
underbonnet fuse box, fit and tighten bolts to 8
Nm (6 lbf.ft).
59.Fit underbonnet fuse box cover.
60.Position 'E' box, secure in retaining clip, fit and
tighten nut to 9 Nm (7 lbf.ft).
61.Position carrier in 'E' box and secure with clips.
62.Position and secure air duct and harness
rubber sleeve in 'E' box.
63.Connect multiplugs securing main harness to
engine harness.
64.Position ECM harness and multiplug to 'E' box,
align harness clamp and secure screws to 'E'
box.
65.Fit engine ECM.

+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - Non NAS.
66.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.67.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
68.Connect battery earth lead.
69.Fill gearbox with fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
70.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.

ENGINE - K SERIES KV6
REPAIRS 12-3-35
Engine and automatic gearbox - from
03MY
$% 12.37.01.99
Remove
1.Disconnect battery earth lead.
2.Tie bonnet back in upright position.
3.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
4.Remove the engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
5.Remove battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
6.Remove engine ECM.

+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - fuel - NAS.
7.Remove bolt securing heated front screen
harness to battery positive cable.
8.Remove 2 screws securing harness clamp and
remove clamp.
9.Release multiplug from 'E' box and disconnect
body harness from engine harness.
10.Move engine harness aside.11.Disconnect multiplug from 'E' box temperature
sensor.
12.Disconnect multiplug from automatic gearbox
ECU.
13.Disconnect 'E' box cooling fan multiplug.
14.Release body harness clip from 'E' box.
15.Move body harness aside.
16.Release air duct from 'E' box.
M00 0000M12 8001

ENGINE - K SERIES KV6
12-3-44 REPAIRS
35.Fit rear beam.

+ FRONT SUSPENSION, REPAIRS,
Rear beam.
36.Fill IRD to correct level with fluid.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) lubrication system -
drain & refill - NAS.
37.Fit exhaust front pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - NAS.
38.With assistant depressing the brake pedal,
tighten front hub nuts to 400 Nm.
39.Stake nuts to drive shafts
40.Fit front road wheels, fit and tighten nuts to 115
Nm.
41.Lower vehicle on lift.
42.Connect brake servo vacuum hose to inlet
manifold chamber.
43.Connect coolant hose to underside of
expansion tank and secure with clip.
44.Connect expansion tank hose to inlet manifold
and secure clip.
45.Connect top hose to radiator and secure with
clip. Position hose in bracket.
46.Connect heater feed and return hoses and
secure with clips.
47.Connect throttle inner cable to throttle cam and
secure outer cable in abutment bracket.
48.Connect hose to purge valve.
49.Fit purge hose into clip.
50.Connect fuel hose to fuel rail pipe, fit rubber
sleeve over hose connector.
51.Connect gearbox harness multiplugs and
secure multiplugs in mounting bracket clips.
52.Connect Lucar connector to starter solenoid.
53.Position earth lead to gearbox housing, fit and
tighten bolt to 25 Nm.
54.Position engine harness to 'E' box mounting
bracket and secure with clips.
55.Connect earth header multiplug.
56.Connect multiplug to under bonnet fuse box.
57.Position battery and starter motor lead to under
bonnet fuse box, fit and tighten bolts to 8 Nm.
58.Fit under bonnet fuse box cover.
59.Position 'E' box, secure in retaining clip, fit and
tighten nut to 9 Nm.
60.Fit carrier to 'E' box.
61.Fit air ducting to 'E' box.
62.Fit body harness to 'E' box, secure grommet
and harness clip.
63.Connect 'E' box cooling fan multiplug.
64.Connect multiplug to 'E' box temperature
sensor.
65.Connect multiplug to gearbox ECU.
66.Position engine harness to 'E' box and secure
grommet.67.Fit engine harness clamp and secure with
screws.
68.Connect engine harness multiplug to body
harness multiplug and fit multiplug to 'E' box.
69.Fit heated front screen harness to battery
positive cable and tighten bolt to 15 Nm (11
lbf.ft).
70.Fit engine ECM.

+ ENGINE MANAGEMENT SYSTEM -
SIEMENS, REPAIRS, Engine control module
(ECM) - fuel - NAS.
71.Fit battery carrier.

+ CHARGING AND STARTING,
REPAIRS, Carrier - battery.
72.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
73.Connect the battery earth lead.
74.Fill gearbox with fluid.

+ AUTOMATIC GEARBOX - JATCO,
ADJUSTMENTS, Gearbox fluid - drain &
refill.
75.Fit the engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
76.Untie and close bonnet.

COOLING SYSTEM - K SERIES KV6
26-3-4 REPAIRS
Radiator assembly
$% 26.40.01
Remove
1.Disconnect battery earth lead.
2.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Drain cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
4. Models without A/C: Remove bumper
valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
5. Models without A/C:Remove 2 bolts securing
PAS fluid cooler to armature.
6. Models without A/C: Remove 4 nuts and 4
bolts securing armature to body and remove
armature.
7. Models with A/C: Remove A/C condenser.

+ AIR CONDITIONING, REPAIRS,
Condenser.
8.Release clips and remove top and bottom
hoses.
CAUTION: Always fit plugs to open
connections to prevent contamination.
9.Release clip and remove expansion hose from
radiator.10. If fitted:Remove 2 bolts and 4 scrivets securing
LH and RH radiator baffles and remove baffles.
11.Remove radiator upper retaining pegs from
bonnet locking platform. Ease top of radiator
forward.
12.Remove 4 bolts securing fan cowl to radiator.
13.Remove 2 cowl retaining clips from radiator.
M26 0947

COOLING SYSTEM - K SERIES KV6
REPAIRS 26-3-5
14.Release radiator from lower mountings and
remove from vehicle.
15.Remove radiator upper mounting extension
brackets.
16.Remove 4 rubber mountings from radiator.Refit
1.Fit mounting rubbers to radiator.
2.Fit upper support brackets to radiator.
3.Position fan cowl to radiator, fit and tighten
bolts to 5 Nm (4 lbf.ft).
4.Secure fan cowl to radiator with clips.
5.Fit radiator and engage lower mountings in
chassis.
6.Fit radiator upper mountings to bonnet locking
platform.
7. If fitted:Position LH and RH radiator baffles,
secure with scrivets, fit and tighten top bolts to
5 Nm (4 lbf.ft).
8.Connect expansion tank hose and secure with
clip.
9.Connect bottom and top hoses to radiator
secure with clips.
10. Models with A/C: Fit A/C condenser.

+ AIR CONDITIONING, REPAIRS,
Condenser.
11. Models without A/C: Position armature, fit and
tighten 4 nuts and bolts securing armature to
body.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
12. Models without A/C: Align PAS fluid cooler
and tighten bolts to 8 Nm (6 lbf.ft).
13. Models without A/C: Fit bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper - assembly - front - up to 04MY.
14.Refill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
15.Fit acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
16.Connect battery earth lead.
M26 0946