seats LAND ROVER FREELANDER 2001 Owner's Manual

RESTRAINT SYSTEMS
REPAIRS 75-11
Stalk - rear seat belt - centre
$% 76.73.98
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
WARNING: When removing, testing or
installing a seatbelt pre-tensioner, do not
lean directly over it or block the end of the
piston tube.
WARNING: Always remove the key from the
starter switch, disconnect the vehicle
battery and wait 10 minutes before
commencing work on the SRS system.
1.Remove RH rear seat.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove 2 screws and remove seat belt reel
cover.3.Remove nut and release seat belt reel.
4.Remove 5 screws and remove both end
covers.
5.Remove 3 Torx bolts and remove squab from
cushion.

RESTRAINT SYSTEMS
75-12 REPAIRS
6.Release rear of cushion cover from frame.
7.Release sides and front of cushion cover from
frame.
8.Release cover and pad from frame.
9.Remove Torx bolt from seat belt buckle and
remove buckle.Refit
1.Position seat belt and buckle to frame and
tighten to 32 Nm (24 lbf.ft).
2.Fit cover and pad to frame.
3.Fit front and sides of cushion cover to frame.
4.Fit rear of cushion cover to frame.
5.Fit cushion to squab and tighten Torx bolts.
6.Fit end covers and tighten screws.
7.Position seat belt reel in seat squab and tighten
nut to 32 Nm (24 lbf.ft).
8.Fit seat belt reel cover and tighten screws.
9.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - RH.

INTERIOR TRIM COMPONENTS
76-3-2 REPAIRS
Trim casing - rear quarter - lower - 5 door
$% 76.13.12
Remove
1.Release rear seat squab and fold seat forward.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Release load space lamp from trim casing.
4.Disconnect 2 Lucars and remove load space
lamp.
5.Remove 2 screws securing casing to load
space carpet retainer.
6.Release 4 turn buckles securing trim casing.
7.Release trim casing from 5 retaining clips.
8.Remove loadspace side trim casing.
9.Remove 5 retaining clips from trim casing.Refit
1.Fit retaining clips to casing.
2.Position casing in loadspace, locate and secure
retaining clips.
3.Fit turn buckles.
4.Fit screws securing casing to carpet retainer.
5.Position load space lamp to casing, connect
Lucars and secure lamp to casing.
6.Position loadspace cover retainer and secure
with screw.
7.Fit loadspace cover and secure in retainers.
8.Position rear seat belt and tighten bolt to 40 Nm
(29 lbf.ft).
9.Reposition rear seats.

INTERIOR TRIM COMPONENTS
76-3-6 REPAIRS
Trim finisher - 'B/C' post - upper - renew
$% 76.13.28
Remove
1.Remove seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Release finisher from 6 retaining clips and
remove finisher.
NOTE: Do not carry out further dismantling if
component is removed for access only.4.Remove 6 retaining clips from finisher.
5.Remove seat belt slide.
Refit
1.Fit seat belt slide to finisher.
2.Fit retaining clips to finisher.
3.Position finisher and engage retaining clips.
4.Position seat belt lower mounting, fit Torx bolt
and tighten to 40 Nm (29 lbf.ft).
5.Fit seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-7
Trim finisher - 'B' post - lower - 5 door
$% 76.13.29
Remove
1.Remove front seat cushion side finisher.

+ SEATS, REPAIRS, Finisher -
cushion side - front seat.
2.Remove scrivet and 5 Torx screws securing
front carpet retainer and remove carpet
retainer.
3.Release 'B/C' post upper finisher.4.Remove 3 Torx screws from top of seat base
finisher.
5.Remove scrivet and Torx screw from 'B/C' post
lower finisher.
6.Release and remove 'B/C' post lower finisher
from seat base finisher.
Refit
1.Locate 'B/C' post lower finisher under seat base
finisher and rear carpet retainer.
2.Fit scrivet and Torx screw to 'B/C' post lower
finisher.
3.Fit Torx screws to seat base finisher.
4.Align and secure 'B/C' post upper finisher.
5.Fit front seat cushion side finisher.

+ SEATS, REPAIRS, Finisher -
cushion side - front seat.
6.Fit carpet retainer and secure with Torx screws
and scrivet.

INTERIOR TRIM COMPONENTS
76-3-8 REPAIRS
Trim casing - body side - rear - 3 door
$% 76.13.57
Remove
1.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Remove 4 Torx bolts securing trim casing to
body.
4.Release 2 trim clips and trim casing.
5.Disconnect multiplug from tweeter if fitted.
6.Remove trim casing.
Do not carry out further dismantling if
component is removed for access only7.Noting the position of the 3 long screws,
remove 10 Torx screws and remove pocket
from trim casing.
8.Remove 3 screws securing pocket finisher to
trim casing and remove finisher.
9.Release 6 tags and remove speaker grille.
Refit
1.Position speaker grille on replacement casing
and secure tags.
2.Fit pocket finisher and secure with screws.
3.Fit pocket and secure with Torx screws.
4.Fit trim clips to trim casing.
5.Position trim casing and if fitted connect
tweeter multiplug.
6.Fit trim casing to body and secure with clips and
Torx screws.
7.Fit seat belt lower fixing and tighten Torx bolt to
50 Nm (37 lbf.ft).
8.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - RH.

SEATS
REPAIRS 76-5-1
SEATS REPAIRS
Front seat
$% 78.10.44.99
Remove
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.
3.Release pretensioner multiplug from seat
frame and disconnect.
4.Remove cover from rear securing bolt.
5.Remove 4 Torx screws securing seat.
6.Remove front seat.
Refit
1.Position front seat and secure with Torx
screws.Tighten screws to 45 Nm (33 lbf.ft).
2.Fit cover to rear bolt.
3.Connect pretensioner multiplug and secure to
seat frame.
4.Fit seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.
Rear seat - LH
$% 78.10.48.99
Remove
1.Remove 2 Torx bolts from seat hinges.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.Remove seat.
Refit
1.Position seat in vehicle and align hinges.
2.Fit Torx bolts to seat hinges and tighten to 25
Nm (18 lbf.ft).
3.Lower seat.
4.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).

SEATS
76-5-2 REPAIRS
Rear seat - RH
$% 78.10.49.99
Remove
1.Remove 2 Torx bolts from seat hinges.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.Remove seat.
Refit
1.Position seat in vehicle and align hinges.
2.Fit Torx bolts to seat hinges and tighten to 25
Nm (18 lbf.ft).
3.Lower seat.
4.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).
Cushion & squab - rear seat - bench type
- 3 door
$% 78.10.57.99
Remove
1.Remove 2 Torx bolts securing seat to heel
board.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.With assistance, remove seat.
Refit
1.With assistance, position seat and align hinges.
2.Fit Torx bolts, lower seat and tighten to 25 Nm
(18 lbf.ft).
3.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).

SEATS
REPAIRS 76-5-3
Cover - one piece - front seat cushion
$% 78.30.01
Remove
1.Remove front seat.

+ SEATS, REPAIRS, Front seat.
2.Remove recline control knob.
3.Release retaining studs from side covers and
remove covers.
4.Disconnect 2 multiplugs from underside of seat
cushion.
5.Release 2 clips securing multiplug to seat
frame.
6.Remove 4 Torx bolts from squab frame and
remove squab frame from cushion frame.7.Release clips securing side edges of cushion
cover to seat frame.
8.Release clip securing front edge of cushion
cover to seat frame.
9.Release main central clip securing rear edge of
cushion cover to seat frame.
10.Release rear of cushion pad from frame.
11.Remove cushion cover and pad.

SEATS
76-5-4 REPAIRS
12.Remove 12 hog rings securing cover to
cushion.
13.Remove cushion cover from cushion.
Refit
1.Position cushion cover to cushion pad and
secure to frame with hog rings in position noted
during removal.
2.Position and secure cushion cover and pad to
frame.
3.Fit squab frame to cushion frame and tighten
Torx bolts to 45 Nm (33 lbf.ft).
4.Connect multiplugs.
5.Position multiplug to frame and secure clips.
6.Fit recline control knob.
7.Fit side covers and secure retaining studs.
8.Fit front seat.

+ SEATS, REPAIRS, Front seat.
Cover - rear seat cushion - RH
$% 78.40.04
Remove
1.Remove RH rear seats.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove 2 screws and remove seat belt reel
cover.
3.Remove nut and release seat belt reel.