torque LAND ROVER FREELANDER 2001 Service Manual

TORQUE WRENCH SETTINGS
06-28
Brakes
1 Use NEW bolts
TORQUE DESCRIPTION METRIC IMPERIAL
ABS ECU pipe unions 17 Nm 12 lbf.ft
ABS modulator to mounting bracket bolts 9 Nm 7 lbf.ft
ABS modulator mounting bracket to inner wing:
⇒ Nuts
⇒ Bolts13 Nm
8 Nm10 lbf.ft
6 lbf.ft
Bleed screw - front calipers 10 Nm 7.5 lbf.ft
Brake servo to bulkhead nuts 22 Nm 16 lbf.ft
EGR cooler to mounting bolts 25 Nm 18 lbf.ft
EGR pipe support bracket to engine lifting bracket bolts 25 Nm 18 lbf.ft
Front caliper brake hose banjo bolt 28 Nm 21 lbf.ft
Front caliper guide pin bolts 27 Nm 20 lbf.ft
Front caliper mounting bolts 100 Nm 74 lbf.ft
Front disc shield to hub screw 8.5 Nm 6.3 lbf.ft
Front disc to drive flange screws 5 Nm 3.7 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Handbrake cable to body and subframe bolts 22 Nm 16 lbf.ft
Handbrake cable retaining plate bolts 22 Nm 16 lbf.ft
Handbrake lever assembly to body bolts 22 Nm 16 lbf.ft
Hill Descent Control (HDC) switch bolt 5 Nm 3.5 lbf.ft
Master cylinder to servo nuts 25 Nm 18 lbf.ft
PAS oil cooler pipe bolts 10 Nm 7.5 lbf.ft
Primary and secondary brake pipe union nuts 17 Nm 12 lbf.ft
Rear wheel cylinder pipe union nut 17 Nm 12 lbf.ft
Rear wheel cylinder to backplate bolts 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 6 Nm 4.5 lbf.ft
Road wheel nuts 115 Nm 85 lbf.ft
Turbocharger intercooler pipe to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger pipe to coolant rail bolt 25 Nm 18 lbf.ft
Vacuum pump bolts
122 Nm 16 lbf.ft
Vacuum reservoir to mounting bracket nut 10 Nm 7.5 lbf.ft

TORQUE WRENCH SETTINGS
06-29
Supplementary Restraint Systems
TORQUE DESCRIPTION METRIC IMPERIAL
SRS Diagnostic Control Unit (DCU) fixing bolts 9 Nm 6.5 lbf.ft
Driver's airbag module to steering wheel Torx screws 9 Nm 6.5 lbf.ft
Front seat belt pre-tensioner to seat Torx bolt 32 Nm 24 lbf.ft
Passenger's airbag module to fascia Torx screws 9 Nm 6.5 lbf.ft

TORQUE WRENCH SETTINGS
06-30
Body
TORQUE DESCRIPTION METRIC IMPERIAL
Doors
Door lock striker to body screws 10 Nm 7 lbf.ft
Door stiffener Torx screws 9 Nm 7 lbf.ft
Front door control unit to glass clamp bolts 9 Nm 7 lbf.ft
Front door hinge bolts 30 Nm 22 lbf.ft
Rear door glass clamp bolts 8 Nm 6 lbf.ft
Tail door exterior handle nuts 5 Nm 3.7 lbf.ft
Tail door glass clamp bolts 8 Nm 6 lbf.ft
Tail door glass regulator lock nuts 14 Nm 10 lbf.ft
Tail door hinge bolts 30 Nm 22 lbf.ft
Exterior Fittings
Bonnet hinge, bolts 9 Nm 6.5 lbf.ft
Bonnet release lever to 'A' post bolt 9 Nm 6.5 lbf.ft
Exterior mirror to door Torx screws 6 Nm 4.4 lbf.ft
Front wing bolts5 Nm 3.7 lbf.ft
Spare wheel mounting bracket:
⇒ Bolts13 Nm 10 lbf.ft
⇒ Nuts25 Nm 18 lbf.ft
Spare wheel to bracket retention nuts 45 Nm 33 lbf.ft
Splash shield bolts 10 Nm 7 lbf.ft
Underbelly panel to body bolts 45 Nm 33 lbf.ft
Underbelly panel to body rear screws 8 Nm 6 lbf.ft
3 door vehicles
Hard back catch Torx screws 10 Nm 7.5 lbf.ft
Hard back retainer Torx screws 10 Nm 7.5 lbf.ft
Soft back support bracket bolts 25 Nm 18 lbf.ft
5 door vehicles
Roof rack side rail bolts 22 Nm 16 lbf.ft
Interior Trim Components
Engine compartment fusebox bolts 8 Nm 6 lbf.ft
Passenger compartment fusebox mounting plate to body and steering column
bracket bolts8 Nm 6 lbf.ft
Passenger compartment fusebox to mounting plate bolts 8 Nm 6 lbf.ft
Seats
Front seat runner to body bolts 45 Nm 33 lbf.ft
Front seat squab frame to cushion frame Torx bolts 45 Nm 33 lbf.ft
Rear bench seat to body bolts 25 Nm 18 lbf.ft
Rear seat cushion to squab Torx bolts 28 Nm 21 lbf.ft
Rear seat catch assembly Torx bolts 32 Nm 24 lbf.ft
Rear seat squab lock Torx screws 20 Nm 15 lbf.ft
Rear seat squab to cushion Torx bolts 28 Nm 21 lbf.ft
Rear seat hinge Torx bolts 25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-31
Seat belts (3-door models)
Front seat belt loop to 'B' post bolt 31 Nm 23 lbf.ft
Front seat belt pre-tensioner and buckle to seat frame Torx bolt 32 Nm 24 lbf.ft
Front seat belt reel bolt 31 Nm 23 lbf.ft
Front seat belt slider bar bolts 40 Nm 30 lbf.ft
Front seat belt lower mounting Torx bolts 40 Nm 30 lbf.ft
Front seat belt upper mounting Torx bolt 31 Nm 23 lbf.ft
Rear seat belt and buckle to frame Torx bolts 32 Nm 24 lbf.ft
Rear seat belt lower fixing to body bolt 50 Nm 37 lbf.ft
Rear seat belt reel to squab nut 32 Nm 24 lbf.ft
Rear seat belt upper mounting bolt 32 Nm 24 lbf.ft
Rear seat squab lock Torx screws 20 Nm 15 lbf.ft
Seat belt pre-tensioner to seat bolt 32 Nm 24 lbf.ft
Seat belts (5-door models)
Front seat belt adjuster to 'B' post Torx bolts 26 Nm 19 lbf.ft
Front seat belt upper anchorage to adjuster mounting nut 31 Nm 23 lbf.ft
Front seat belt lower fixing to 'B' post bolt 40 Nm 30 lbf.ft
Front seat belt pre-tensioner and buckle to seat frame Torx bolt 32 Nm 24 lbf.ft
Front seat belt reel bolt 31 Nm 23 lbf.ft
Rear centre seat belt reel to seat squab nut 32 Nm 24 lbf.ft
Rear seat belt and buckle bolts 32 Nm 24 lbf.ft
Rear side seat belt lower fixing bolt 40 Nm 30 lbf.ft
Rear side seat belt reel bolt 50 Nm 37 lbf.ft
Rear side seat belt buckle to catch assembly bolt 32 Nm 24 lbf.ft
Rear side seat belt upper mounting bolt 32 Nm 24 lbf.ft
Seat belt height adjuster bolts 26 Nm 19 lbf.ft
Screens
Sun roof side rail Torx bolts 22 Nm 16 lbf.ft TORQUE DESCRIPTION METRIC IMPERIAL

TORQUE WRENCH SETTINGS
06-32
Heating and Ventilation
TORQUE DESCRIPTION METRIC IMPERIAL
Air intake hose and bracket assembly to fuel burning heater bolts (Td4) 10 Nm 7.5 lbf.ft
Exhaust pipe clamp bolts (Td4) 5 Nm 3.5 lbf.ft
Fuel burning heater to body bolts (Td4) 8 Nm 6 lbf.ft
Fuel burning heater to mounting bracket bolts (Td4) 8 Nm 6 lbf.ft
Heater to fascia nuts 8 Nm 6 lbf.ft
Heater to bulkhead bolt 8 Nm 6 lbf.ft
Evaporator to bulkhead bolts 8 Nm 6 lbf.ft

TORQUE WRENCH SETTINGS
06-33
Air Conditioning
TORQUE DESCRIPTION METRIC IMPERIAL
A/C compressor to mounting bracket bolts (Td4 & K1.8) 25 Nm 18 lbf.ft
A/C compressor mounting bracket to cylinder block bolts (Td4 & K1.8) 45 Nm 33 lbf.ft
A/C compressor mounting bracket to cylinder block bolts (KV6) 45 Nm 33 lbf.ft
A/C compressor support bracket to sump bolt (Td4) 10 Nm 7.5 lbf.ft
A/C compressor drive belt tensioner clamp bolt (Td4) 24 Nm 18 lbf.ft
A/C compressor drive belt tensioner pivot bolt (Td4) 24 Nm 18 lbf.ft
A/C compressor upper and lower securing bolts (KV6) 25 Nm 18 lbf.ft
A/C pipe rail to condenser bolt (KV6) 8 Nm 6 lbf.ft
A/C pipe rail to condenser bolt (KV6) 8 Nm 6 lbf.ft
Condenser bracket to radiator bolts 8 Nm 6 lbf.ft
Receiver drier to condenser bolts 12 Nm 9 lbf.ft
Refrigerant pressure sensor 10 Nm 7.5 lbf.ft
TXV to bulkhead Allen screws 25 Nm 18 lbf.ft

TORQUE WRENCH SETTINGS
06-34
Wipers and Washers
TORQUE DESCRIPTION METRIC IMPERIAL
Rear wiper arm nut 13 Nm 10 lbf.ft
Rear wiper motor bolts 5 Nm 3.7 lbf.ft
Rear wiper motor spindle nut 5 Nm 3.7 lbf.ft
Windscreen wiper arm nut 18 Nm 13 lbf.ft
Windscreen wiper motor and linkage to body bolts 5 Nm 3.7 lbf.ft

TORQUE WRENCH SETTINGS
06-35
Electrical
TORQUE DESCRIPTION METRIC IMPERIAL
Alternator drive belt tensioner bolt 25 Nm 18 lbf.ft
Alternator mounting bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator pivot and adjustment bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator to front mounting plate nut and bolts (KV6) 45 Nm 33 lbf.ft
Alternator support bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator pivot and adjustment bracket bolts (K1.8) 25 Nm 18 lbf.ft
Alternator to mounting bracket bolts (Td4):
⇒ M825 Nm 18 lbf.ft
⇒ M1045 Nm 9.5 lbf.ft
Alternator upper and lower bolts (K1.8 with A/C) 45 Nm 33 lbf.ft
Ancillary drive belt idler pulley to mounting Allen bolt (Td4) 25 Nm 18 lbf.ft
Battery cable to alternator terminal nut (Td4 & KV6) 10 Nm 7.5 lbf.ft
Battery cable to starter motor solenoid nut (K1.8) 8 Nm 6 lbf.ft
Battery cable to starter motor solenoid nut (K1.8) 13 Nm 9.5 lbf.ft
Battery clamp bolt 12 Nm 9 lbf.ft
Battery and starter motor lead to underbonnet fusebox bolts 8 Nm 6 lbf.ft
'E' box mounting nut 9 Nm 7 lbf.ft
Passenger compartment fusebox mounting plate to body bolts 8 Nm 6 lbf.ft
Passenger compartment fusebox to mounting plate bolts 8 Nm 6 lbf.ft
Starter motor mounting bolts (Td4) 45 Nm 33 lbf.ft
Starter motor to engine upper and lower nuts and bolts (K1.8) 45 Nm 33 lbf.ft
Starter motor to engine upper and lower nuts and bolts (K1.8) 80 Nm 59 lbf.ft

MAINTENANCE
10-6 MAINTENANCE
Alarm Handset Battery
Replace
1.Insert the blade of a small, flat bladed
screwdriver into the slot at the keyring end of
the handset and carefully prise the two halves
of the handset apart.
2.Slide the battery out of the clip taking care not
to touch the circuit board or the battery
contacts.
3.Press and hold each button in turn for at least 5
seconds to drain any residual power from the
handset.
4.Fit the replacement battery (Land Rover
STC4080 or Panasonic CR2032) ensuring the
correct polarity is maintained (+) side facing
upwards. Avoid touching the flat surfaces of the
battery.
5.Press the 2 halves of the handset together,
making sure the two halves click into place
correctly.
6.Check the operation of the handset.
Road Wheels
Remove
1.Loosen wheel nuts. Raise vehicle for wheel
free condition and remove the wheel nuts.
2.Mark the wheel to stud relationship to ensure
that the wheels are refitted in the same
orientation.
Refit
1.Apply a thin coat of anti-seize compound to
wheel hub centre.
2.Refit wheels to original hub position.
NOTE: When refitting road wheel nuts, do not
overtighten using powered tools. Ensure the
wheel nuts are correctly torqued in the correct
sequence.
3.Tighten wheel nuts to 115 Nm (85 lbf.ft).

MAINTENANCE
MAINTENANCE 10-27
Suspension
Check Front Suspension
1.Check condition of all ball joint dust covers,
including anti-roll bar links.
2.Check tightness of all accessible suspension
fixings including tie rods.
3.Check wheel bearings and suspension struts
for signs of excessive play or wear.
4.Check track rod ends for wear by attempting to
move the joint forwards and backwards, side to
side and up and down. No wear should be
apparent, if any is detected then the joint must
be replaced.
5.Check for signs of leakage from suspension
dampers.Check Rear Suspension
1.Check tightness of all accessible suspension
fixings including transverse links.
2.Check wheel bearings and suspension struts
for signs of excessive play or wear.
3.Check for signs of leakage from suspension
dampers.
Check Tow Bar Fixings
1.Check that the two vertical fixings are tightened
to a torque of 110 Nm (82 lbf.ft).
2.Check that the six transverse fixings are
tightened to a torque of 60 Nm (45 lbf.ft).