lock LAND ROVER FRELANDER 2 2006 Owner's Guide

Publ is hed: 27-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Steering
Angle Sensor Module (SASM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the ant i lock cont rol s tabil it y s yst em, refer to the relevant Des cri pt ion and Operati on s ect ionin the workshop manual.For addit ional informat ion, refer t o: Anti -Lock Cont rol - St abi li ty As s is t (206-09C Anti -Lock Cont rol - St abi lit y As s is t,Des cript ion and Operat ion).
Steering Angle Sensor Module
DT CDescriptionPossible CauseAction
U0001-00High Speed CANCommunicati on BusGeneral Fai lureInformat ion No s ub typeinformat ion
Bus OffCarry out t he pinpoint t es t s as sociat ed to thi s DTCus ing the manufact urer approved di agnos ti c s yst em
U0140-00Lost Communi cat ion W it hCentral el ect ronic modul eGeneral Fai lureInformat ion No s ub typeinformat ion
Lost communicat ion wi thCJBCarry out t he pinpoint t es t s as sociat ed to thi s DTCus ing the manufact urer approved di agnos ti c s yst em
U0300-00Int ernal Control ModuleSoft ware Incompat ibi lit yGeneral Fai lureInformat ion No s ub typeinformat ion
CAN Bus faul tLoss of power t o moduleIncorrect componentins t al ledModule i nternal fai lure
Carry out CAN net work and power feed t es ts us ingmanufact urer approved di agnos t ic s yst em. Checkcorrect s t eering wheel rot ati on s ens or is ins tall ed.Ins tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.
U3000-04Control Module GeneralFailure Informat ionSyst em Int ernal Fail ures
CAN Bus faul tLoss of power t o moduleIncorrect componentins t al ledModule i nternal fai lure
Carry out CAN net work and power feed t es ts us ingmanufact urer approved di agnos t ic s yst em. Checkcorrect s t eering wheel rot ati on s ens or is ins tall ed.Ins tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.U3000-14Control Module GeneralElectrical Fai lures Ci rcuits hort t o ground or open
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-1DControl Module GeneralElectrical Fai lures Ci rcuitcurrent out of range
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-44Control Module Sys t emInt ernal Failures Datamemory fai lure
Module i nternal fai lureIns tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.U3000-48Control Module Sys t emInt ernal FailuresSupervis ion s oft warefai lure
Module i nternal fai lureIns tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.
U3000-49Control Module Sys t emInt ernal Failures Int ernalelectronic fai lure
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-61Control Module Algori thmBas ed Fai lures Si gnalcalcul ati on fai lure
Steering wheel rot at ions ens or mi s-ali gnedModule i nternal fai lure
Check for correct i nst all at ion of s ens or. Ins t al l anew st eeri ng wheel rotat ion s ensor as requi red,refer t o new module/component ins tal lati on note att he t op of the DTC Index.

Publi s hed: 05-May-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC:
Transmission Control Module (TCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under ma nufacturer warrant y, refer t o t he
W arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or appr oval program is i n operat ion, before
t he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t c odes . Match t he 5 digi ts from t he s can
t ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the las t 2 digi ts gi ve ext ra informati on read by the
manufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci mal
places, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al wa ys take t he res is t ance of t he DMM
leads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi n g pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or co rros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is no t present , an int ermi tt ent concern may
be t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the trans mi ss i on cont rol s ys t em, refer to t he relevant Des cript ion and O perati on sect ion i n the
works hop manual . For addit ional informat ion, refer t o: Trans mis s ion Des cript ion (307-01 Aut omati c
Trans mis s ion/Transaxle, Des cript ion and Operat ion).
Transmission control module (TCM) DT C Description Possible Cause Action
P0218-68 Trans mis s ion flui d
overtemperat ure condit ion Transmis si on fluid level l ow Transmis si on fluid
cooler/hos es are
obs t ructed/damaged/blocked. Mechanical fault i n the
trans mi ss i on Check t he transmis s ion fluid level and
condit ion. Check t he t rans mis s ion flui d cool er
/hos es for s igns of obst ruct ion/damage
/blockage. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
trans mi s si on is sus pect .
P0500-00 Vehi cle s peed s ens or A
(out put s haft s peed
s ens or) Vehi cl e s peed sens or A
ci rcuit : short ci rcuit t o ground Vehi cl e s peed sens or A
ci rcuit : open ci rcuit Vehi cl e s peed sens or A faul t Check t he vehi cl e s peed sens or A and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
P056-100 Sys t em volt age unst able Bat tery faul t Chargi ng s yst em fault Check t he batt ery and charging sys tems . Refer
to the el ect ri cal guides. Recti fy as neces sary.
P0562-00 Sys t em volt age low Bat tery faul t Chargi ng s yst em fault
P0601-00
Int ernal cont rol module
memory checksum error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Reconfi gure t he module us ing the approved
di agnos t ic s yst em.
P0603-00 Int ernal cont rol module
keep al ive memory (KAM)
error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0604-00 Int ernal cont rol module
random acces s memory
(RAM) error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0605-00
Int ernal cont rol module
read only memory (ROM)
error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0614-00
Engi ne cont rol module
(ECM)/t rans mi ss i on cont rol
module (TCM) incompati bl e Incorrect s oft ware i n TCM Reconfi gure t he module us ing the approved
di agnos t ic s yst em.
P062F-00 Int ernal cont rol module
electrically eras abl e
programmabl e read onl y
memory (EEPROM) error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0705-00 Trans mis s ion range sens or
A circui t (PRNDL i nput ) Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he adjus tment of t he gear s elector l ever
cable and sens or.
For addit ional informati on, refer t o: Sel ect or Lever Cabl e Adjus t ment (307-05 Aut omati c
Transmis s ion/Trans axle External Cont rols ,
General Procedures ).
Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0706-00 Trans mis s ion range sens or
A circui t range/performance Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol Check t he adjus tment of t he gear s elector l ever
cable.
For addit ional informati on, refer t o: Sel ect or Lever Cabl e Adjus t ment (307-05 Aut omati c
Transmis s ion/Trans axle External Cont rols ,

DT C
Description Possible Cause Action
P073F-00 Unabl e t o engage gear 1 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion. Mechanical fault i n the
trans mi ss i on P0741-00
Torque convert er clutch
s ol enoi d circui t
performance/s tuck off Cont act resi s tance in the
terminals Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o ground Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o power Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : open ci rcuit Torque convert er cl ut ch lock
up sol enoi d (SLU) s t uck i n off
pos it ion Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion or t he TCM i s
sus pect .
P0742-00 Torque convert er clutch
s ol enoi d circui t st uck on Cont act resi s tance in the
terminals Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o ground Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o power Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : open ci rcuit Torque convert er cl ut ch lock
up sol enoi d (SLU) s t uck i n on
pos it ion Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0744-68
Torque convert er clutch
s ol enoi d circui t
int ermi tt ent Engine st all ed Mechanical fault i n engi ne Carry out a compl ete read for related engi ne
DTCs . Recti fy as necess ary.
P074A-00 Unabl e t o engage gear 2 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on Check t rans mis s ion flui d level and condit ion.
Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P074B-00 Unabl e t o engage gear 3 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on P074C-00
Unabl e t o engage gear 4 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on P074D-00
Unabl e t o engage gear 5 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on P074E-00
Unabl e t o engage gear 6 Cont act resi s tance in the
terminals Sol enoi ds st uck in t he on/off
pos it ion Mechanical fault i n the
trans mi ss i on P0777-00
Pres s ure control s olenoid B
s tuck on Shi ft s olenoid No. 2 st uck in
the on pos it ion Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.

DT C
Description Possible Cause Action
P0897-09 Trans mis s ion flui d
deteri orat ed Transmis si on fluid no longer
servi ceable Drain and refill t he t rans mis s ion wi th fresh
fl ui d. For addit ional informati on, refer t o:
(307-01 Aut omati c Trans mis s ion/Trans axle)
Trans mi s si on Fluid Drain and Refil l - I6 3.2L Pet rol (General Procedures ),
Trans mi s si on Fluid Drain and Refil l - TD4 2.2L Dies el (General Procedures).
P0928-13 Gear shi ft l ock s olenoid
circuit open Gear s hift lock s olenoi d
ci rcuit : open ci rcuit Gear s hift lock s olenoi d faul t Check t he gear s hift lock s olenoid and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
P0930-11 Gear shi ft l ock s olenoid
circuit l ow Gear s hift lock s olenoi d
ci rcuit : short ci rcuit t o ground Gear s hift lock s olenoi d faul t
P0931-12
Gear shi ft l ock s olenoid
circuit hi gh Gear s hift lock s olenoi d
ci rcuit : short ci rcuit t o power Gear s hift lock s olenoi d faul t
P0960-00
Pres s ure control s olenoid A
cont rol circui t open Li ne pres s ure control
sol enoid (SLT) circuit : s hort
ci rcuit t o ground Li ne pres s ure control
sol enoid (SLT) circuit : open
ci rcuit Li ne pres s ure control
sol enoid (SLT) fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P0961-00 Pres s ure control s olenoid A
cont rol circui t
range/performance Li ne pres s ure control
sol enoid (SLT) circuit : s hort
ci rcuit t o ground Li ne pres s ure control
sol enoid (SLT) circuit : open
ci rcuit Li ne pres s ure control
sol enoid (SLT) circuit : s hort
ci rcuit t o power Li ne pres s ure control
sol enoid (SLT) fault P0963-00
Pres s ure control s olenoid A
cont rol circui t hi gh Li ne pres s ure control
sol enoid (SLT) circuit : s hort
ci rcuit t o power Li ne pres s ure control
sol enoid (SLT) fault P0964-00
Pres s ure control s olenoid B
cont rol circui t open Torque convert er cl ut ch lock
up cont rol s ol enoi d
(SLU)circui t: s hort ci rcuit t o
ground Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : open ci rcuit Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P0965-00 Pres s ure control s olenoid B
cont rol circui t
range/performance Torque convert er cl ut ch lock
up cont rol s ol enoi d
(SLU)circui t: s hort ci rcuit t o
ground Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : open ci rcuit Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o power Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
fault P0967-00
Pres s ure control s olenoid B
cont rol circui t hi gh Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
ci rcuit : short ci rcuit t o power Torque convert er cl ut ch lock
up cont rol s ol enoi d (SLU)
fault P0969-00
Pres s ure control s olenoid C
cont rol circui t
range/performance C2 Pres sure cont rol s olenoid
(SLC2) ci rcuit : short ci rcuit t o
ground C2 Pres sure cont rol s olenoid
(SLC2) ci rcuit : open ci rcuit C2 Pres sure cont rol s olenoid Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.

DT C
Description Possible Cause Action
(SLC2) ci rcuit : short ci rcuit t o
power
C2 Pres sure cont rol s olenoid
(SLC2) fault P0970-00
Pres s ure control s olenoid C
cont rol circui t low C2 Pres sure cont rol s olenoid
(SLC2) ci rcuit : short ci rcuit t o
ground C2 Pres sure cont rol s olenoid
(SLC2) ci rcuit : open ci rcuit C2 Pres sure cont rol s olenoid
(SLC2) fault P0971-00
Pres s ure control s olenoid C
cont rol circui t hi gh C2 Pres sure cont rol s olenoid
(SLC2) ci rcuit : short ci rcuit t o
power C2 Pres sure cont rol s olenoid
(SLC2) fault P0973-00
Shift sol enoid A control
circuit l ow Shi ft s olenoid No. 1 ci rcuit :
short ci rcuit t o ground Shi ft s olenoid No. 1 ci rcuit :
open circui t Shi ft s olenoid No. 1 fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P0974-00 Shift sol enoid A control
circuit hi gh Shi ft s olenoid No. 1 ci rcuit :
short ci rcuit t o power Shi ft s olenoid No. 1 fault
P0976-00
Shift sol enoid B control
circuit l ow Shi ft s olenoid No. 2 ci rcuit :
short ci rcuit t o ground Shi ft s olenoid No. 2 ci rcuit :
open circui t Shi ft s olenoid No. 2 fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P0977-00 Shift sol enoid B control
circuit hi gh Shi ft s olenoid No. 2 ci rcuit :
short ci rcuit t o power Shi ft s olenoid No. 2 fault
P1783-68
Trans mis s ion
overtemperat ure condit ion Transmis si on fluid level l ow Transmis si on fluid
cooler/hos es are
obs t ructed/damaged/blocked. Mechanical fault i n the
trans mi ss i on The trans mi ss i on has been
expos ed to hi gh load and
hi gh ambient t emperature. Check t he transmis s ion fluid level and
condit ion. Check t he t rans mis s ion flui d cool er
/hos es for s igns of obst ruct ion/damage
/blockage. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
trans mi s si on is sus pect .
P1799-00 Cont rol ler area net work
(CAN) t rans mi ss ion cont rol
module ( TCM)/ant i-lock
brake s yst em (ABS) circuit
malfunct ion CAN circuit fault (bet ween
ABS modul e (brake cont rol
modul e(BCM)) and TCM ABS (BCM) module fault Check t he CAN circui ts . Refer t o t he electrical
gui des . Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
ABS module (BCM) is sus pect .
P2158-00 Vehi cle Speed Sens or B
(i nput s haft s peed s ens or
(ISS)) ISS s ensor circui t: s hort
ci rcuit t o ground ISS s ensor circui t: s hort
ci rcuit t o power ISS s ensor circui t: open
ci rcuit ISS s ensor faul t Check t he ISS sens or and ci rcuit s. Refer to t he
el ect ri cal guides . Ins t al l a new ISS s ens or as
neces sary.
For addit ional informati on, refer t o: Input Shaft Speed (ISS) Sensor - I6 3.2L Pet rol (307-01
Aut omati c Trans mis s ion/Transaxle, Removal
and Ins tal lati on) /
Input Shaft Speed (ISS) Sens or - TD4 2.2L Dies el (307-01 Aut omat ic
Transmis s ion/Trans axle, Removal and
Ins tal lati on).
P2719-00 Pres s ure control s olenoid D
cont rol circui t
range/performance Press ure cont rol s olenoid
(SLC3) ci rcuit : short ci rcuit t o
ground Press ure cont rol s olenoid
(SLC3) ci rcuit : open ci rcuit Press ure cont rol s olenoid
(SLC3) ci rcuit : short ci rcuit t o
power Press ure cont rol s olenoid
(SLC3) fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P2720-00 Pres s ure control s olenoid D
cont rol circui t low Press ure cont rol s olenoid
(SLC3) ci rcuit : short ci rcuit t o
ground Press ure cont rol s olenoid
(SLC3) ci rcuit : open ci rcuit Press ure cont rol s olenoid
(SLC3) fault

DT C
Description Possible Cause Action
P2721-00 Pres s ure control s olenoid D
cont rol circui t hi gh Press ure cont rol s olenoid
(SLC3) ci rcuit : short ci rcuit t o
power Press ure cont rol s olenoid
(SLC3) fault P2728-00
Pres s ure control s olenoid E
cont rol circui t
range/performance Press ure cont rol s olenoid
(SLB1) ci rcuit : short ci rcuit t o
ground Press ure cont rol s olenoid
(SLB1) ci rcuit : open ci rcuit Press ure cont rol s olenoid
(SLB1) ci rcuit : short ci rcuit t o
power Press ure cont rol s olenoid
(SLB1) fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P2729-00 Pres s ure control s olenoid E
cont rol circui t low Press ure cont rol s olenoid
(SLB1) ci rcuit : short ci rcuit t o
ground Press ure cont rol s olenoid
(SLB1) ci rcuit : open ci rcuit Press ure cont rol s olenoid
(SLB1) fault P2730-00
Pres s ure control s olenoid E
cont rol circui t hi gh Press ure cont rol s olenoid
(SLB1) ci rcuit : short ci rcuit t o
power Press ure cont rol s olenoid
(SLB1) fault P2733-00
Pres s ure control s olenoid F
s tuck on SLC1 s olenoid has jammed Mechanical fault s in
trans mi ss i on Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P2737-00 Pres s ure control s olenoid F
cont rol circui t
range/performance Press ure cont rol s olenoid
(SLC1) ci rcuit : short ci rcuit t o
ground Press ure cont rol s olenoid
(SLC1) ci rcuit : open ci rcuit Press ure cont rol s olenoid
(SLC1) ci rcuit : short ci rcuit t o
power Press ure cont rol s olenoid
(SLC1) fault P2738-00
Pres s ure control s olenoid F
cont rol circui t low Press ure cont rol s olenoid
(SLC1) ci rcuit : short ci rcuit t o
ground Press ure cont rol s olenoid
(SLC1) ci rcuit : open ci rcuit Press ure cont rol s olenoid
(SLC1) fault P2739-00
Pres s ure control s olenoid F
cont rol circui t hi gh Press ure cont rol s olenoid
(SLC1) ci rcuit : short ci rcuit t o
power Press ure cont rol s olenoid
(SLC1) fault P2783-68
Torque convert er
temperature too hi gh Transmis si on fluid level l ow Transmis si on fluid
cooler/hos es are
obs t ructed/damaged/blocked. Mechanical fault i n the
trans mi ss i on The trans mi ss i on has been
expos ed to ext reme load and
hi gh ambient t emperature Check t he transmis s ion fluid level and
condit ion. Check t he t rans mis s ion flui d cool er
/hos es for s igns of obst ruct ion/damage
/blockage. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
trans mi s si on is sus pect .
P2787-68 Clut ch temperat ure too
high Transmis si on fluid level l ow Transmis si on fluid
cooler/hos es are
obs t ructed/damaged/blocked. Mechanical fault i n the
trans mi ss i on The trans mi ss i on has been
expos ed to ext reme load and
hi gh ambient t emperature Check t he transmis s ion fluid level and
condit ion. Check t he t rans mis s ion flui d cool er
/hos es for s igns of obst ruct ion/damage
/blockage. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
trans mi s si on is sus pect .

DT C
Description Possible Cause Action
P2800-00 Trans mis s ion range sens or
B circui t (PRNDL i nput ) Incorrect adjus tment of t he
gear s elector lever cabl e Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t hat t he gear sel ect or lever cable is
correctl y adjus ted.
For addit ional informati on, refer t o: Sel ect or Lever Cabl e Adjus t ment (307-05 Aut omati c
Transmis s ion/Trans axle External Cont rols ,
General Procedures ).
Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect
P2801-00
Trans mis s ion range sens or
B circui t range/performance Incorrect adjus tment of t he
gear s elector lever cabl e Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P2805-00
Trans mis s ion range sens or
A/B correl at ion Incorrect adjus tment of t he
gear s elector lever cabl e Int ernal t rans mi ss i on cont rol
modul e (TCM) fault U0001-00
High s peed cont rol ler area
network (CAN)
communicat ion bus CAN circuit : open circuit CAN circuit : s hort circui t to
each ot her CAN circuit : s hort circui t to
power CAN cont rol module fail ure Carry out a compl ete vehicle read for DTCs
indicati ng a CAN or module fault . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if a module i s s uspect.
U0100-00 Los t communicati on wi th
ECM "A" CAN circuit : open circuit CAN circuit : s hort circui t to
each ot her CAN circuit : s hort circui t to
power CAN cont rol module fail ure Carry out a compl ete vehicle read for DTCs
indicati ng a CAN or module fault . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if a module i s s uspect.
U0121-00 Cont rol ler area net work
(CAN) t rans mi ss ion cont rol
module ( TCM)/ant i-lock
brake s yst em (ABS) circuit
malfunct ion no
communicat ion CAN circuit : open circuit CAN circuit : s hort circui t to
each ot her CAN circuit : s hort circui t to
power CAN cont rol module fail ure Carry out a compl ete vehicle read for DTCs
indicati ng a CAN or module fault . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if a module i s s uspect.
U0300-00 Int ernal cont rol module
s oft ware i ncompat ibil it y Incorrect cont rol ler area
net work (CAN) configurat ion
ID
- incorrect
hardware/s oft ware level Check t hat t he modules are correct for the
vehicl e and that t he correct level of software is
ins tall ed. Reconfi gure t he CAN s yst em us i ng the
approved di agnos ti c s ys t em.
U0401-00 Invali d data recei ved from
engi ne cont rol module
(ECM) Incorrect s ignal from t he ECM Carry out a compl ete vehicle read for DTCs
indicati ng a cont rol ler area net work (CAN) or
ECM faul t. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
ECM is sus pect .
U0415-00 Invali d data recei ved from
the ant i-lock brake s ys tem
(ABS) control modul e The engine cont rol module
(ECM) has t he wrong code for
the i mmobil izer The ABS modul e (brake
control modul e (BCM)) has
the wrong code for the
immobi lizer Transmis si on cont rol module
(TCM) faul t Reprogramme the modules as neces sary. Refer
to the warranty pol icy and procedures manual if
a module i s s uspect.
U2100-00 Ini ti al confi gurati on not
compl ete Cont roll er area network
(CAN) circui t fault Init ial cent ral confi gurati on
has never been sent Check for ot her controll er area network (CAN)
DTCs or apparent ly unrel at ed cust omer
compl ai nts . Carry out a complet e vehi cl e DTC
read. Check t he CAN circui ts . Refer t o t he
el ect ri cal guides . Rect ify as neces s ary. Clear
the DTCs and t es t for normal operat ion. Check
correct cent ral car confi gurati on s oftware i s
ins tall ed. Reprogramme t he module as
neces sary.
U2101-00 Cont rol module
configurat ion i ncompat ible Cent ral car confi gurati on
parameter mi ss i ng or
corrupted Check correct central car configurat ion s oft ware
is i nst all ed. Reprogramme t he module as
neces sary.
U2023-00 Engi ne t orque s ignal Cont roll er area network
(CAN) circui t (between
engine cont rol module (ECM)
and trans mi ss i on cont rol
modul e (TCM)): open ci rcuit CAN circuit (between ECM
and TCM): s hort circui t CAN module fault Carry out a compl ete read for related DTCs .
Rect ify as neces s ary. Check t he CAN circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
U2105-11 Swit ch pack s i gnal "A" Shi ft l ock s olenoid ci rcuit
fault : s hort ci rcuit t o ground Gear s elector module (GSM)
fault Check t he GSM and circui ts . Refer t o t he
el ect ri cal guides . Rect ify as neces s ary. Refer to
the warrant y pol icy and procedures manual if
the GSM is s us pect .

VIN PositionCharacterIdentifies
9 - Check digi t4Deri ved by calculat ion: 0-9 or X
10 - Model year8200810 - Model year92009
11 - Pl antHHalewood
12 -17 - Serial number100314Unique s ix di git s eri al number
VIN number - NAS and Canada (vehicles built from 2010MY)
VIN PositionCharacterIdentifies
1 - 3 - W orld ident ifierSALLand Rover (UK)
4 - Model rangeFLR25 - Clas sPNAS SE
5 - Clas sRNAS HSE
5 - Clas sSNAS SE+Lux pack5 - Clas sTNAS HSE+Lux pack
6 - Body Type24 Door
7 - Transmis s ion and St eeringBLHD, Aut omati c t ransmis s ion8 - Engi neN3.2L Petrol, ULEV 2 NAS
9 - Check digi t4Deri ved by calculat ion: 0-9 or X
10 - Model yearA201010 - Model yearB2011
10 - Model yearC2012
11 - Pl antHHalewood12 -17 - Serial number100314Unique s ix di git s eri al number
2.0 Liter Petrol Engine Serial Number
The 2.0 Li ter Petrol Engi ne Serial Number is st amped on t he RH s ide of t he cylinder block.
2.2 Liter Diesel Engine Serial Number

The 2.2 Li ter Di es el Engi ne Seri al Number i s s tamped on t he RH si de of the cyli nder block.
3.2 Liter Petrol Engine Serial Number
The 3.2 Li ter Petrol Engi ne Serial Number is et ched into the LH s ide of t he engi ne block.
Automatic Transmission Serial Number
The Automat ic Trans mi s si on Serial Number is st amped on t he LH s ide of t he t rans mis s ion cas ing.
Manual Transmission Serial Number

• NOTE: To enable t he vehi cle t o be s upport ed correctl y on t he wheel -free longit udi nal s, i t wil l be neces s ary t o produce 2off each of the support blocks t o the di mens ions given in the accompanying ill ust rations . The s upport ing part of each bl ockmus t be manufactured from s uit able hardwood or met al and the 'U' shaped bas e of each bl ock mus t be manufact ured frommet al . Note that it i s es sent ial to ens ure that t he 'U' s haped bas e of each block is wide enough to fit over t he wheel freelongit udinals .
Front s upport bl ock di mens ions
ItemPart NumberDescriptionA-130 mm (5.118 in)
B-160 mm (6.299 in)
C-90 mm (3.543 in)Rear support block dimens i ons
ItemPart NumberDescription
A-50 mm (1.1968 in)B-190 (7.480 in)
C-110 (4.330 in)
Rais ing and Support ing t he Vehicle
1. Posi ti on vehi cl e on ramp.
2. Appl y parking brake.
3. Rais e ramp t o required height
4. Ali gn the wheel -free l ongi tudinals and pos it ion the s upport blocks beneat h the pos it ions s hown