engine LAND ROVER FRELANDER 2 2006 Repair Manual

SymptomPossible CauseAction
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Torque derate,regenerat ion l ocked out(DTC P244D00 al so logged)
Downs tream catalyt ic convertert emperature s ens or volt ageabove upper li mi tSensor failure
Refer to the el ect ri cal circui t diagrams and checkdowns t ream cat al yti c convert er temperat ure sens orci rcuit for short to power. Ins tal l new temperat uresens or as required
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Regenerat ionl ocked out (DTC P245300als o l ogged)
Part iculat e fi lt er st ati onarycorrect ed different ial pres s urebelow mini mum
Different ial pres s ure s ensor hos es cross ed over
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Torque derate,regenerat ion l ocked out(DTC P245500 al so logged)
Part iculat e fi lt er different ialpres s ure s ens or volt age aboveupper l imitSensor failure
Refer to the el ect ri cal circui t diagrams and checkdifferent ial pres sure s ens or s uppl y circuit for s hortto power. Ins tal l a new s ensor as requi red
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Torque derate,regenerat ion l ocked out(DTC P245600 al so logged)
Leaki ng or blocked di fferenti alpres s ure s ens or hos esDi fferenti al pres s ure sens orcircui t short, open circui tSensor failure
Check for spl it /degraded, bl ocked different ialpres sure s ens or hoses , refer to el ect ri cal circui tdiagrams and check different ial pres sure s ens orci rcuit s for s hort , open ci rcuit . Ins t al l a new s ensoras required
'O il Service requi red'mes s age dis played (DTCP250F00 al so dis played)
Engine oil contami nat edCheck engine oi l condit ion, renew as requi red
'O il Service requi red'mes s age dis played (DTCP252F00 al so dis played)
Engine oil contami nat edCheck engine oi l condit ion, renew as requi red
'O il Service requi red'mes s age dis played (DTCP253F00 al so dis played)
Engine oil contami nat edCheck engine oi l condit ion, renew as requi red
'Reduced Engi nePerformance' mes s agedis played. No effect t odri veabi lit y, regenerati onreduced t o lower level (2)(DTC P208000 al so logged)
Exhaus t gas t emperature s ens or1 pl aus i bi li ty faultRefer to elect rical circui t diagrams and checkups t ream cat alyti c convert er temperat ure sens orci rcuit for short ci rcuit , open ci rcuit
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Regenerat ionl ocked out (DTC P244A00als o l ogged)
Signal not pl aus i bl e. Different ialpres s ure s ens or hos e l inedefecti ve
Check for correct ins tall ati on and int egrit y ofdifferent ial pres sure s ens or hoses , rect ify asrequired
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Torque derate,regenerat ion l ocked out(DTC P244B22 al so logged)
Signal ampli tude > maximum.Part iculat e fi lt er uncorrect eddifferent ial pres s ure value abovel imi t in after run
CAUTION: All i nt ake air s yst em leaks MUST berecti fi ed before carrying out dynamic regenerat ion.
Check for correct ins tall ati on and int egrit y ofdifferent ial pres sure s ens or hoses , rect ify asrequired. Check for correct i ns t allat ion and i ntegri tyof intake ai r sys tem, rect ify as requi red. Carry outdynami c regenerati on us ing t he manufacturerapproved di agnos ti c s ys t em'DPF Ful l' mes sagedis played, wit h s ee handbook icon (DTC P245200 al sol ogged)
Poor drivi ng st yle, unabl e t ofaci lit ate regenerati onRefer dri ver t o hand book
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Torque derate,regenerat ion l ocked out(DTC P245400 al so logged)
Part iculat e fi lt er different ialpres s ure s ens or volt age belowl ower l imi tSensor failure
Refer to the el ect ri cal circui t diagrams and checkdifferent ial pres sure s ens or s uppl y circuit for s hort,open ci rcuit . Ins tal l a new s ensor as requi red
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Torque derate,regenerat ion l ocked out(DTC P208400 al so logged)
Exhaus t gas t emperature s ens or2 pl aus i bi li ty faultRefer to elect rical circui t diagrams and checkdowns t ream cat al yti c convert er temperat ure sens orci rcuit for short ci rcuit , open ci rcuit
'Reduced Engi nePerformance' mes s agedis played. No effect t odri veabi lit y, regenerati onreduced t o lower level (2)(DTC P054617 al so logged)
Pre-cat alyt ic convertert emperature s ens or circui tvolt age above t hres hol d
Refer to elect rical circui t diagrams and checkpre-cat al yti c convert er temperat ure s ens or ci rcuitfor s hort t o power
'Reduced Engi nePerformance' or 'EngineSyst em Fault ' mes sagedis played. Regenerat ionl ocked out (DTC P244A00
Signal not pl aus i bl e. Different ialpres s ure s ens or hos e l inedefecti ve
Check for correct ins tall ati on and int egrit y ofdifferent ial pres sure s ens or hoses , rect ify asrequired

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Camshaft Position (CMP)
Sensor
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
2. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
2.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m andOrnament ati on, Removal and Ins tal lat ion).
3.
4.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Crankshaft Position (CKP)
Sensor
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he front wheel .
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2. 3.
4. CAUTION: Make s ure that the wiring harnes s es
are correctl y located.
T orque: 8 Nm 4.
Installation To i nst all , revers e t he removal procedure.
1.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Engine Coolant Temperature
(ECT) Sensor
Removal and Inst all ati on
Removal
Remove t he air cleaner as s embly.
Refer t o: Air Cleaner (303-12A Intake Ai r Dis tribut ion and Fil tering -I6 3.2L Pet rol, Removal and Ins t al lat ion).
1.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m andOrnament ati on, Removal and Ins tal lat ion).
2.
Drai n t he cool ing s ys tem.
Refer t o: Cool ing Sys tem Drai ni ng, Fi lli ng and Bleeding (303-03BEngine Cooli ng - TD4 2.2L Di esel , General Procedures ).
3.
4. W ARNING: Do not work on or under a vehi cle s upported onl yby a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
4.
5. CAUTIONS:
Be prepared t o collect es caping coolant.
A new O-ri ng s eal i s to be ins tal led.
5.
6. NOTE: Remove and dis card t he O-ring seal.6.

7.
Installation
Connect t he engi ne cool ant t emperat ure (ECT) sens or el ect ri calconnector.1.
2. CAUTION: A new O-ring seal is to be ins tall ed.
Inst all t he engi ne cool ant t emperat ure (ECT) sens or.
2.
Connect t he heat er out let pi pe.3.
Inst all t he air cleaner as s embly.
Refer t o: Air Cleaner (303-12A Intake Ai r Dis tribut ion and Fil tering -I6 3.2L Pet rol, Removal and Ins t al lat ion).
4.
Inst all t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m andOrnament ati on, Removal and Ins tal lat ion).
5.
Refi ll and bleed t he cool ing s ys tem.
Refer t o: Cool ing Sys tem Drai ni ng, Fi lli ng and Bleeding (303-03BEngine Cooli ng - TD4 2.2L Di esel , General Procedures ).
6.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Manifold Absolute Pressure
(MAP) Sensor
Removal and Inst all ati on
Removal 1.
T orque:
10 Nm 2.
Installation To i nst all , revers e t he removal procedure.
1.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Intake Air Temperature (IAT)
Sensor
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m andOrnament ati on, Removal and Ins tal lat ion).
2.
3.
4.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Heated Oxygen Sensor
(HO2S)
Removal and Inst all ati on
Special T ool(s) 310-121
W rench, H02S
Removal W ARNING: Observe due care when worki ng near a hot exhaust s ys tem.
1. W ARNING: Do not work on or under a vehi cle s upported onl y
by a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m and
Ornament ati on, Removal and Ins tal lat ion).
2. 3.
Us ing t he s peci al t ool, remove the heated oxygen
s ensor (HO2S).
Speci al Tool (s ): 310-121 4.
Installation For H02S ant i-s eize compound i nformati on, refer t o the specificati on
1.

s ect ion.
Refer t o: Specificati ons (303-08B Engine Emis si on Control - TD4 2.2L
Di es el, Specifi cat ions ).
2. CAUTION: Make s ure the ant i-sei ze compound does not
cont act the HO2S ti p.
Apply ant i-sei ze compound t o t he s ens or threads .
2.
Inst all t he HO2S.
Speci al Tool (s ): 310-121 T orque:
45 Nm 3.
Connect t he HO2S electrical connect or.
4.
Inst all t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m and
Ornament ati on, Removal and Ins tal lat ion).
5.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Engine Oil Pressure (EOP)
Sensor
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Rais e and s upport t he vehi cl e.2.
Remove t he engi ne undershi eld.
Refer t o: Engi ne Unders hi eld (501-02 Front End Body Panel s ,Removal and Ins tall ati on).
3.
4.
5.