engine LAND ROVER FRELANDER 2 2006 Repair Manual

6.
CAUTIONS: Be prepared t o collect es caping flui ds .
Replace t he was her.
T orque: 32 Nm 6.
Installation To i nst all , revers e t he removal procedure.
1.
Check and top-up the engine oi l if required.
2.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Intake Manifold Runner
Control (IMRC) Actuator
Removal and Inst all ati on
Removal
Remove t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m and
Ornament ati on, Removal and Ins tal lat ion).
1. T orque:
10 Nm 2.
Installation To i nst all , revers e t he removal procedure.
1.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Mass Air Flow (MAF) Sensor
Removal and Inst all ati on
Removal T orque:
2 Nm 1.
Installation To i nst all , revers e t he removal procedure.
1.
2. NOTE: For NAS vehicl es onl y.
If required, carry out a s hort dri ve cycle.
Refer t o: Powertrain Cont rol Modul e (PCM) Short Dri ve Cycl e
Self-Tes t (303-14A, General Procedures ).
2.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Crankshaft Position (CKP)
Sensor Ring
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he cranks haft pull ey.
Refer t o: Crankshaft Pul ley (303-01B Engi ne - TD4 2.2L Dies el ,Removal and Ins tall ati on).
2.
3. CAUTION: "Make sure t hat a new component isi ns t alled. "
• NOTE: M6 bol ts can be us ed t o extract t hecomponent .
• NOTE: Make s ure that t hi s component is ins tal led t ot he noted removal pos it ion.
3.
Installation
To i nst all , revers e t he removal procedure.1.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Engine Control Module (ECM)
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he plenum chamber panel.
Refer t o: Plenum Chamber (412-01 Cl imat e Control, Removal and
Inst all at ion).
2. 3.
Petrol ECM s hown, di es el s imi lar.
4. T orque:
6 Nm 5.
Installation

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Fuel Temperature Sensor
Removal and Inst all ati on
Removal
• W ARNINGS: Avoid flames , s parks or li ght ed s ubs t ances .
W ai t for a mini mum of 1 minute aft er the engine has s t opped before carryi ng out any
repair t o t he fuel inject ion
s ys t em.
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - TD4 2.2L Dies el (501-05 Interior Tri m and
Ornament ati on, Removal and Ins tal lat ion).
2. T orque:
10 Nm 3.
4.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Oil Temperature Sensor
Removal and Inst all ati on
Removal
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he s tart er mot or.
Refer t o: Start er Motor (303-06B Starti ng Sys t em - TD4 2.2L Dies el,
Removal and Ins tall ati on).
2. 3. CAUTION: Make s ure that a new s eali ng was her
i s ins tal led.
T orque: 27 Nm 3.
Installation To i nst all , revers e t he removal procedure.
1.
Check and top-up the engine oi l if required.
2.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Clutch Pedal Position (CPP)
SwitchLHD AWD
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
Remove t he dri ver l ower ai r bag.
Refer t o: Dri ver Lower Air Bag Module (501-20B SupplementalRes traint Sys t em, Removal and Inst all at ion).
2.
3.
Installation
To i nst all , revers e t he removal procedure.1.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Clutch Pedal Position (CPP)
SwitchRHD AWD
Removal and Inst all ati on
Removal
Di sconnect t he bat t ery ground cable.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
Remove t he dri ver l ower ai r bag.
Refer t o: Dri ver Lower Air Bag Module (501-20B Supplemental
Res traint Sys t em, Removal and Inst all at ion).
2. 3.
4.
Installation To i nst all , revers e t he removal procedure.
1.

Publi s hed: 11-May-2011
Electronic Engine Controls - TD4 2.2L Diesel - Exhaust Gas Temperature
Sensor
Removal and Inst all ati on
Removal
W ARNING: Observe due care when worki ng near a hot exhaust s ys tem.
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Do not work on or under a vehi cle s upported onl yby a jack. Al ways support t he vehi cl e on s afet y s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he engi ne cover.
Refer t o: Engi ne Cover - 2.2L Dies el (501-05, Removal andInst all at ion).
2.
3.