POWER switch Lexus CT200h 2011 (in English) Manual Online

570
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Warning messageDetailsCorrection procedure
Indicates that the hood
is not fully closedClose the hood.
Indicates that the back
door is not fully closed
If the vehicle reaches a
speed of 5 km/h
(3 mph), a buzzer
sounds to indicate that
the back door is not
yet fully closed.
Close the back door.
(Flashes)
Indicates that the moon
roof is not fully closed
(with the “POWER”
switch off, and the
driver’s door open)
Close the moon roof.
Warns the rear passen-
ger to fasten his/her seat
belt
If a rear passenger
once fastens their seat
belt and then unfastens
it, the warning mes-
sage will appear on the
display and a buzzer
*1
will sound.
Fasten the seat belt.

5
571
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Warning messageDetailsCorrection procedure
(Flashes)
Indicates, if the vehicle
reaches a speed of 5 km/
h (3 mph), that the park-
ing brake is still engaged
Release the parking
brake.
(Flashes)
Indicates that the
“POWER” switch is
turned off or turned to
ACCESSORY mode
and the driver’s door is
opened while the lights
are turned on.
Turn the lights off.
(If equipped)
Indicates that Lexus
parking assist-sensor is
dirty or covered with
ice
Clean the sensor.

578
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Once3
times
(Flashes)
The electronic
key was carried
outside the vehi-
cle and a door
other than the
driver’s door
was opened and
closed while the
“POWER”
switch was in a
mode other than
off.
Bring the elec-
tronic key back
into the vehicle.
The electronic
key was carried
outside the vehi-
cle and the
driver’s door
was opened and
closed while the
shift position P
was selected
without turning
off the
“POWER”
switch.
Turn the
“POWER”
switch off or
bring the elec-
tronic key back
into the vehicle.

5
579
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Once
Con-
tinu-
ous
(Displayed alter-
nately)
(Flashes)
An attempt was
made to exit the
vehicle with the
electronic key
and lock the
doors without
first turning the
“POWER”
switch off.
Turn the
“POWER”
switch off and
lock the doors
again.
Once
(Flashes)
An attempt was
made to start the
hybrid system
without the elec-
tronic key being
present, or the
electronic key
was not func-
tioning nor-
mally.
An attempt was
made to drive
when the regular
key was not
inside the vehi-
cle.
Confirm that the
electronic key is
inside the vehi-
cle.

580
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Con-
tinu-
ous

(Flashes)
The driver’s
door was opened
while any shift
position other
than P was
selected without
turning off the
“POWER”
switch.
Shift the shift
position to P.
Con-
tinu-
ousCon-
tinu-
ous
(Displayed alter-
nately)
(Flashes)
The electronic
key was carried
outside the vehi-
cle and the
driver’s door
was opened and
closed while any
shift position
other than P was
selected without
turning off the
“POWER”
switch.
• Shift the shift
position to P.
• Bring the elec-
tronic key back
into the vehi-
cle.

582
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Once
(Flashes)
•When the
doors were
unlocked with
the mechanical
key and then
the “POWER”
switch was
pressed, the
electronic key
could not be
detected in the
vehicle.
• The electronic
key could not
be detected in
the vehicle
even after the
“POWER”
switch was
pressed two
consecutive
times.
Touch the elec-
tronic key to the
“POWER”
switch while
depressing the
brake pedal.
Once
(Flashes)
An attempt was
made to start the
hybrid system
with the shift
position in N.Shift the shift
position to P and
start the hybrid
system.

584
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Interior
buzzerExte-
rior
buzzer
Warning messageDetailsCorrection
procedure
Once
(Flashes)
The driver’s
door was opened
and closed with
the “POWER”
switch turned
off and then the
“POWER”
switch was put
in ACCES-
SORY mode
twice without
the hybrid sys-
tem being
started.
Press the
“POWER”
switch while
depressing the
brake pedal.
During a hybrid
system starting
procedure in the
event that the
electronic key
was not func-
tioning properly
(P. 617), the
“POWER”
switch was
touched with the
electronic key.
Press the
“POWER”
switch within 10
seconds of the
buzzer sound-
ing.

5
601
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
Taking out the emergency tire puncture repair kit
Remove the center deck board.
Emergency tire puncture repair kit components
Insertion keyPower plug
Hose
Stickers
Air release
Compres-
sor switch Air pressureBottle
STEP1

604
5-2. Steps to take in an emergency
CT200h_EE (OM76041E)
Emergency repair method
Pull the insertion key out of the
kit.
Place the kit with the bottom
facing upward.
Peel off the label, and push in
the insertion key until a click is
heard.
Return the kit to an upright
position and make sure that the
compressor switch is off.
Use the kit with the top facing
upward.
Connect the power plug to the
power outlet socket. (P. 451)
STEP1
STEP2
STEP3
STEP4

5
607
5-2. Steps to take in an emergency
When trouble arises
CT200h_EE (OM76041E)
• If the needle of the air pres-
sure gauge reaches the red
zone (450 kPa [4.5 kgf/cm
2
or bar, 65 psi] or more),
there may be a malfunction
in the tire or in the kit itself.
Stop operation immediately.
• If the tire inflation pressure
is still lower than the recom-
mended level after inflation
for 10 minutes with the
switch on, the tire is too
damaged to be repaired.
Turn the compressor switch
off and contact any autho-
rized Lexus dealer or
repairer, or another duly
qualified and equipped pro-
fessional.
• If the tire inflation pressure
exceeds the recommended
level, let out some air to
adjust the tire inflation pres-
sure.
(P. 6 1 1 )
Disconnect the hose from the valve on the tire and then pull
out the power plug from the power outlet socket.
To spread the liquid sealant evenly within the tire, immedi-
ately drive for about 5 km (3 miles).STEP 12
STEP 13