warning light Lexus CT200h 2014 (in English) User Guide

431-1. For safe use
1
CT200h_OM_OM76135E_(EE)
For safety and security
The main SRS airbag system components are shown above. The SRS airbag sys-
tem is controlled by the airbag sensor assembly. As the airbags deploy, a chemi-
cal reaction in the inflators quickly fills the airbags with non-toxic gas to help
restrain the motion of the occupants.
SRS airbag system components
Front passenger airbag
“PASSENGER AIR BAG” indicator
Side airbags
Curtain shield airbags
Side impact sensors (rear)
SRS warning light
Driver airbag
Side impact sensors (front) Seat belt pretensioners and force
limiters
Driver’s seat belt buckle switch
Driver’s seat position sensor
Knee airbags
Front impact sensors
Airbag sensor assembly
Airbag manual on-off switch1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CT200h_OM_OM76135E_(EE).book Page 43 Friday, May 30, 2014 11
:14 AM

761-2. Hybrid system
CT200h_OM_OM76135E_(EE)
■If a warning light comes on, a warning message is displayed, or the 12-volt battery is dis-
connected
The hybrid system may not start. In this case, try to start the system again. If the “READY”
indicator does not come on, contact any authorized Lexus dealer or repairer, or another
duly qualified and equipped professional.
■Running out of fuel
When the vehicle has run out of fuel and the hybrid system cannot be started, refuel the
vehicle with at least enough gasoline to make the low fuel level warning light (→P. 5 1 7 )
go off. If there is only a small amount of fu el, the hybrid system may not be able to start.
(The minimum amount of fuel to add to make the low fuel level warning light go out is
about 11.8 L [3.1 gal., 2.6 Imp.gal.], when the vehicle is on a level surface. This value may
vary when the vehicle is on a slope. Add extra fuel when the vehicle is inclined.)
■Electromagnetic waves
●High voltage parts and cables on hybrid vehicles incorporate electromagnetic shield-
ing, and therefore emit approximately the same amount of electromagnetic waves as
conventional gasoline powered vehicles or home electronic appliances.
●Your vehicle may cause sound interference in some third party-produced radio parts.
■Hybrid battery (traction battery)
The hybrid battery (traction battery) has a lim ited service life. The lifespan of the hybrid
battery (traction battery) can change in accordance with driving style and driving condi-
tions.
■Declaration of conformity
This model conforms to hydrogen emissions according to regulation ECE100 (Battery
electric vehicle safety).
WA R N I N G
■High voltage precautions
This vehicle has high voltage DC and AC systems as well as a 12-volt system. DC and
AC high voltage is very dangerous and can cause severe burns and electric shock that
may result in death or serious injury.
●Never touch, disassemble, remove or replace the high voltage parts, cables or their
connectors.
●The hybrid system will become hot after starting as the system uses high voltage. Be
careful of both the high voltage and the high temperature, and always obey the cau-
tion labels attached to the vehicle.
●Never try to open the service plug access
hole located in the luggage compartment.
The service plug is used only when the vehicle
is serviced and is subject to high voltage.
CT200h_OM_OM76135E_(EE).book Page 76 Friday, May 30, 2014 11 :14 AM

91
2Instrument cluster
CT200h_OM_OM76135E_(EE)
2. Instrument clusterWarning lights and indicators ....................................... 92
Gauges and meters ..................... 96
Multi-information display (with monochrome
display) ......................................... 100
Multi-information display (with color display) .................. 103
Energy monitor/ consumption screen ............... 106
CT200h_OM_OM76135E_(EE).book Page 91 Friday, May 30, 2014 11 :14 AM

922. Instrument cluster
CT200h_OM_OM76135E_(EE)
Warning lights and indicators
XVehicles with monochrome display
XVehicles with color display
The units used on the meter may differ depending on the target region.
The warning lights and indicators on th e instrument cluster and center panel
inform the driver of the status of the vehicle’s various systems.
For the purpose of explanation, the following illustration displays all warning
lights and indicators illuminated.
CT200h_OM_OM76135E_(EE).book Page 92 Friday, May 30, 2014 11 :14 AM

932. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76135E_(EE)
Warning lights inform the driver of malfunctions in any of the vehicle’s systems.
Wa r n i n g l i g h t s
*1Brake system warning light
(→ P. 5 1 5 )*1Slip indicator light
(→ P. 5 1 7 )
*1Brake system warning light
(→ P. 5 1 5 )*1
(if equipped)
Automatic headlight
leveling system warning
light ( →P. 5 1 7 )
*1Charging system warning
light ( →P. 5 1 5 )*1High coolant temperature
warning light ( →P. 5 1 7 )
*1Low engine oil pressure
warning light ( →P. 5 1 5 ) Open door warning light
(
→ P. 5 1 7 )
*1Malfunction indicator lamp
(→ P. 5 1 6 ) Low fuel level warning light
(
→ P. 5 1 7 )
*1SRS warning light
(→ P. 5 1 6 ) Driver’s and front
passenger’s seat belt
reminder light (
→P. 5 1 7 )
*1ABS warning light
(→ P. 5 1 6 )*3Rear passengers’ seat
belt reminder lights
(→ P. 5 1 7 )
*1Electric power steering
system warning
light ( →P. 5 1 6 )*1Master warning light
(→ P. 5 1 7 )
*1, 2
(if equipped)
“PCS” warning light
(→ P. 5 1 6 )*1
(if equipped)
Tire pressure warning light
(→ P. 5 1 8 )
CT200h_OM_OM76135E_(EE).book Page 93 Friday, May 30, 2014 11 :14 AM

942. Instrument cluster
CT200h_OM_OM76135E_(EE)
*1: These lights turn on when the power switch is turned to ON mode to indicate that asystem check is being performed. They will turn off after the hybrid system is on, or
after a few seconds. There may be a malfunction in a system if the lights do not turn on,
or turn off. Have the vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional.
*2: The light flashes to indicate a malfunction.
*3: This light illuminates on the center panel.
The indicators inform the driver of the operating state of the vehicle’s various sys-
tems.
Indicators
Turn signal indicator
(→ P. 1 8 8 ) “ECO MODE” indicator
(
→ P. 2 3 7 )
Tail light indicator
( → P. 1 9 0 ) “SPORT MODE”
indicator (
→P. 2 3 7 )
Headlight high beam
indicator ( →P. 1 9 0 )
(if equipped)
Cruise control indicator
(→ P. 205, 208)
(if equipped)
Front fog light indicator
(→ P. 1 9 4 )
(if equipped)
Radar cruise control
indicator ( →P. 2 0 8 )
Rear fog light indicator
( → P. 1 9 4 )
(if equipped)
Lexus parking
assist-sensor indicator
(→ P. 2 1 9 )
“READY” indicator
( → P. 177)
*1, 2Slip indicator light
(→ P. 2 3 9 , 2 4 2 )
EV indicator ( →P. 7 2 )
*1“TRC OFF” indicator
(→ P. 2 3 9 )
EV drive mode indicator
( → P. 181)
*1, 3
(if equipped)
“PCS” warning light
(→ P. 244)
CT200h_OM_OM76135E_(EE).book Page 94 Friday, May 30, 2014 11 :14 AM

952. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76135E_(EE)
*1: These lights turn on when the power switch is turned to the ON mode to indicate thata system check is being performed. They will turn off after the hybrid system is on, or
after a few seconds. There may be a malfunction in a system if the lights do not turn on,
or turn off. Have the vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional.
*2: The light flashes to indicate that the system is operating.
*3: The light comes on when the system is turned off. The light flashes faster than usual to indicate that the system is operating.
*4: This light illuminates on the center panel. Shift position indicators
(
→ P. 1 8 3 )
*1, 4“PASSENGER AIR
BAG” indicator
(→ P. 5 1 )
WA R N I N G
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not come on when
you start the hybrid system, this could mean that these systems are not available to help
protect you in an accident, which could result in death or serious injury. Have the vehi-
cle inspected by any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional immediately if this occurs.
CT200h_OM_OM76135E_(EE).book Page 95 Friday, May 30, 2014 11 :14 AM

992. Instrument cluster
2
Instrument cluster
CT200h_OM_OM76135E_(EE)
●Hybrid System Indicator is displayed when the driving mode is in other than the sport
mode.
●By keeping the indicator needle within Ec o area, more Eco-friendly driving can be
achieved.
●Charge area indicates regeneration* status. Regenerated energy will be used to
charge the hybrid battery (traction battery).
*: When used in this manual, “regeneration” refers to the conversion of energy created
by the movement of the vehicle into electrical energy.
■Tachometer (if equipped)
The tachometer is displayed when the driving mode is in the sport mode.
■ECO lamp and SPORT lamp (if equipped)
●When sport mode is selected, the SPORT lamp (red) will illuminate.
●When all of the following conditions are satisfied and the Eco-friendly driving, the ECO
lamp (blue) will illuminate:
• Driving with the shift position in D
• Either normal mode or Eco drive mode is selected, and EV drive mode is not in use
( → P. 1 8 1 , 2 3 7 )
• The vehicle speed is approximately 130 km/h (80 mph) or below.
■Engine speed
On hybrid vehicles, engine speed is precis ely controlled in order to help improve fuel
efficiency and reduce exhaust emissions etc.
There are times when the engine speed that is displayed may differ even when vehicle
operation and driving co nditions are the same.
■Outside temperature display
●In the following situations, the correct outside temperature may not be displayed, or the
display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 20 km/h [12 mph])
• When the outside temperature has changed suddenly (at the entrance/exit of a
garage, tunnel, etc.)
●When “--” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to any authorized Lexus de aler or repairer, or another duly qualified
and equipped professional.
■Customization
Settings (e.g. on/off operation of the ECO lamp) can be changed.
(Customizable features: →P. 5 8 9 )
NOTICE
■To prevent damage to the engine and its components
●Vehicles with tachometer: Do not let the indicator needle of the tachometer enter the
red zone, which indicates the maximum engine speed.
●The engine may be overheating if the high coolant temperature warning light comes
on or flashes. In this case, immediately stop the vehicle in a safe place, and check the
engine after it has cooled completely. ( →P. 5 7 1 )
CT200h_OM_OM76135E_(EE).book Page 99 Friday, May 30, 2014 11 :14 AM

1653-5. Opening, closing the windows and moon roof
3
Operation of each component
CT200h_OM_OM76135E_(EE)
■The moon roof can be operated when
The power switch is in ON mode.
■Operating the moon roof after turning the hybrid system off
The moon roof can be operated for approximately 45 seconds even after the power
switch is turned to ACCESSORY mode or turned off. It cannot, however, be operated
once either front door is opened.
■Jam protection function
If an object is detected between the moon roof and the frame while the moon roof is clos-
ing or tilting down, travel is stoppe d and the moon roof opens slightly.
■Sunshade
The sunshade can be opened and closed manually. However, the sunshade will open
automatically to slightly before the fully op en position when the moon roof is opened.
■When the moon roof does not close normally
Perform the following procedure:
●If the moon roof closes but then re-opens slightly
Stop the vehicle.
Press and hold the “CLOSE” switch.
*1
The moon roof will close, reopen an d pause for approximately 10 seconds.*2 Then it
will close again and tilt down. Finally it w ill be adjusted slightly and then stop.
Check to make sure that the moon roof completely stops and then release the
switch.
●If the moon roof tilts down but then tilts back up
Stop the vehicle.
Press and hold the “DOWN” switch.
*1
The moon roof will close, reopen and paus e for approximately 10 seconds in the tilt
up position.
*2 Then it will close again and tilt down . Finally it will be adjusted slightly
and then stop.
Check to make sure that the moon roof has completely stopped and then release
the switch.
*1: If the switch is released at the incorrect time, the procedure will have to be per-
formed again from the beginning.
*2: If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the “CLOSE” or “DOWN”
switch, and the moon roof will close, be adjusted slightly and then stop. Check to
make sure that the moon roof has completely stopped and then release the switch.
If the moon roof does not fully close even after performing the above procedure cor-
rectly, have the vehicle inspected by any authorized Lexus dealer or repairer, or another
duly qualified and equipped professional.
■Moon roof open warning buzzer
The buzzer sounds and a message is shown on the multi-information display in the instru-
ment cluster when the power switch is turned off and the driver’s door is opened with the
moon roof open.
1
2
3
1
2
3
CT200h_OM_OM76135E_(EE).book Page 165 Friday, May 30, 2014 1 1:14 AM

1854-2. Driving procedures
4
Driving
CT200h_OM_OM76135E_(EE)
■For the shift positions
●When the power switch is off, the shift position cannot be changed.
●When the power switch is in ON mode (the hybrid system is not operating), the shift
position can only be changed to N. The shif t position will be changed to N even if the
shift lever is shifted to D or R and held in that position.
●When the “READY” indicator is on, the shift position can be changed from P to D, N or
R.
●When the “READY” indicator is flashing, the shift position cannot be changed from P to
another position even if the shift lever is operated. Wait until the “READY” indicator
changes from a flashing to a solid light, and then operate the shift lever again.
●The shift position can only be changed to B directly from D.
In addition, if an attempt is made to change the shift position by moving the shift lever or
by pressing the P position switch in any of the following situations, the buzzer will sound
and the shifting operation will be disabled or the shift position will automatically change
to N. When this happens, select an appropriate shift position.
●Situations where the shifting operation will be disabled:
• When an attempt is made to change the shift position from P to another position by moving the shift lever without depressing the brake pedal.
• When an attempt is made to change the shift position from P or N to B by moving
the shift lever.
●Situations where the shift position will automatically change to N:
• When the P position switch is pressed while the vehicle is running.
*1
• When an attempt is made to select the R position by moving the shift lever when the
vehicle is moving forward.
*2
• When an attempt is made to select the D position by moving the shift lever when thevehicle is moving in reverse.
*3
• When an attempt is made to change the shift position from R to B by moving the shiftlever.
*1: Shift position may be changed to P when driving at extremely low speeds.
*2: Shift position may be changed to R when driving at low speeds.
*3: Shift position may be changed to D when driving at low speeds.
■Reverse warning buzzer
When shifting into R, a buzzer will sound to info rm the driver that the shift position is in R.
■About engine braking
When shift position B is selected, releasing the accelerator pedal will apply engine brak-
ing.
• When the vehicle is driven at high speeds, compared to ordinary gasoline-fueled vehi-
cles, the engine braking deceleration is felt less than that of other vehicles.
• The vehicle can be accelerated even when shift position B is selected.
If the vehicle is driven contin uously in the B position, fuel efficiency will become low. Usu-
ally, select the D position.
CT200h_OM_OM76135E_(EE).book Page 185 Friday, May 30, 2014 1 1:14 AM