high beam Lexus CT200h 2017 Owner's Manual (in English)

84
CT200h_OM_OM76215U_(U)2. Instrument cluster
*1: These lights turn on when the power switch is turned to ON mode to indicate that a
system check is being performed. They will turn off after the hybrid system is on, or
after a few seconds. There may be a malfunction in a system if the lights do not turn on,
or turn off. Have the vehicle inspected by your Lexus dealer.
*2: The light flashes to indicate a malfunction.
The indicators inform the driver of the operating state of the vehicle’s various sys-
tems.
Indicators
Turn signal indicator
(  P. 1 7 0 ) “ECO MODE” indicator
(
 P. 2 3 7 )
(U.S.A.)
Headlight indicator
( P. 1 7 2 ) “SPORT MODE” indicator
(
 P. 2 3 7 )
(Canada)
Tail light indicator
( P. 1 7 2 ) Cruise control indicator
(
 P. 1 8 9 , 1 9 2 )
Headlight high beam
indicator ( P. 1 7 3 )
(if equipped)
Radar cruise control
indicator ( P. 1 9 2 )
Fog light indicator
(  P. 1 7 5 )
(if equipped)
Intuitive parking assist
indicator ( P. 2 0 5 )
“READY” indicator
(  P. 1 5 9 )
*1, 2Slip indicator light
( P. 2 3 9 )
EV indicator ( P. 6 9 )
*1“TRAC OFF” indicator
( P. 2 3 9 )
EV drive mode indicator
(  P. 1 6 3 )
*1, 3
(if equipped)
“PCS” warning light
( P. 2 4 2 )
Shift position indicators
(  P. 1 6 5 )
*1, 4“A I R B A G O N /
OFF” indicator
( P. 4 9 )

CT200h_OM_OM76215U_(U)
1734-3. Operating the lights and wipers
4
Driving
Ty p e BThe daytime running lights
turn on. ( P. 1 7 3 )
The side marker, parking,
tail, license plate, daytime
running lights ( P. 1 7 3 )
and instrument panel lights
turn on.
The headlights and all the
lights listed above (except
daytime running lights) turn
on.
The headlights, side marker,
parking lights, daytime run-
ning lights ( P. 1 7 3 ) a n d s o
on turn on and off automati-
cally (when the power
switch is in ON mode).
With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
Pull the lever toward you and release
it to flash the high beams once.
You can flash the high beams with the
headlights on or off.
■Daytime running light system
To make your vehicle more visible to other drivers during daytime driving, the daytime
running lights turn on automatically whenever the hybrid system is started and the park-
ing brake is released with the headlight swit ch off or in the “AUTO” position. (Illuminate
brighter than the parking lights.) Daytime ru nning lights are not designed for use at night.
For the U.S.A.: Daytime running lights can be turned off by operating the switch.
1
2
3
4
Turning on the high beam headlights
1
2

514
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
Light bulbs
Check the wattage of the light bulb to be replaced. (
P. 585)
 P. 4 8 4
■Front
Vehicles with halogen headlights
You may replace the following bulbs by yourself. The difficulty level of replace-
ment varies depending on the bulb. If necessary bulb replacement seems diffi-
cult to perform, contact your Lexus dealer.
For more information about replacing other light bulbs, contact your Lexus
dealer.
Preparing for light bulb replacement
Removing the engine compartment cover
Bulb locations
Front turn signal light
Halogen fog light (if equipped) Headlight low beam
Headlight high beam1
2
3
4

CT200h_OM_OM76215U_(U)
5157-3. Do-it-yourself maintenance
7
Maintenance and care
Vehicles with LED headlightsHeadlight high beam
Front turn signal light
■RearBack-up light
Rear turn signal light
1
2
1
2

CT200h_OM_OM76215U_(U)
5177-3. Do-it-yourself maintenance
7
Maintenance and care
■Headlight high beams (halogen headlights)For the right side only: Move the
washer fluid filler opening.
Unplug the connector while
pressing the lock release.
Turn the bulb base counterclock-
wise.
Set the new light bulb.
Align the 3 tabs on the light bulb with
the mounting, and insert. Turn it
clockwise to set.
1
2
3
4

518
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
Set the connector.
After installing the connector, shake
the bulb base gently to check that it is
not loose, turn the headlight high
beams on once and visually confirm
that no light is leaking through the
mounting.
For the right side only: Reinstall the washer fluid filler opening.
■Headlight high beams (LED headlights)
Turn the cover counterclockwise
and remove it.
Turn the bulb base counterclock-
wise.
Unplug the connector while pull-
ing the lock release.
5
6
1
2
3

CT200h_OM_OM76215U_(U)
5197-3. Do-it-yourself maintenance
7
Maintenance and care
Replace the light bulb, and install
the bulb base.
Align the 3 tabs on the light bulb with
the mounting, and insert.
Turn and secure the bulb base.
Shake the bulb base gently to check
that it is not loose, turn the headlight
high beams on once and visually
confirm that no light is leaking
through the mounting.
When installing the cover, conduct step in reverse.
■Halogen fog light (if equipped)Remove 2 screws, a bolt and clip,
and pull down the fender liner.
Pull the fender liner down slowly,
being careful not to dislodge any
fixed components.
4
5
61
1

524
CT200h_OM_OM76215U_(U)7-3. Do-it-yourself maintenance
Turn the bulb base counterclock-
wise.
Remove the light bulb.
■Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by your Lexus
dealer.
●Headlight low beams (LED type)
●Parking lights and daytime running lights
●LED fog lights (if equipped)
●Front side marker lights
●Side turn signal lights
●Stop/tail lights
●Rear side marker lights
●High mounted stoplight
●License plate lights
●Outer foot lights
■After replacing the bulbs
2
3
After removing the power control unit cover,
return the cover to original position with the
clips.
Push up center portion
Insert
Press
1
2
3

CT200h_OM_OM76215U_(U)
5257-3. Do-it-yourself maintenance
7
Maintenance and care
■LED lights
The headlight low beams (LED type), parking lights, front side marker lights, daytime
running lights, LED fog lights (if equipped), side turn signal lights, rear side marker lights,
stop/tail lights, high mounted stoplight and license plate lights consist of a number of
LEDs. If any of the LEDs burn out, take your vehicle to your Lexus dealer to have the light
replaced.
■Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not indicate a
malfunction. Contact your Lexus dealer for mo re information in the following situations:
●Large drops of water have built up on the inside of the lens.
●Wa t e r h a s b u i l t u p i nside the headlight.
■When replacing light bulbs
P. 5 1 3
WA R N I N G
■Replacing light bulbs
●Be sure to stop the hybrid system and turn off the lights. Do not attempt to replace the
bulb immediately after turning off the lights.
The bulbs become very hot and may cause burns.
●Do not touch the glass portion of the light bulb with bare hands. When it is unavoid-
able to hold the glass portion, use and ho ld with a clean dry cloth to avoid getting
moisture and oils on the bulb.
Also, if the bulb is scratched or dropped, it may blow out or crack.
●Fully install light bulbs and any parts used to secure them. Failure to do so may result
in heat damage, fire, or water entering the headlight unit. This may damage the head-
lights or cause condensation to build up on the lens.
●Do not attempt to repair or disassemble light bulbs, connectors, electric circuits or
component parts.
Doing so may result in death or se rious injury due to electric shock.
■To prevent damage or fire
●Make sure bulbs are fully seated and locked.
●Check the wattage of the bulb before installin g to prevent heat damage.

CT200h_OM_OM76215U_(U)
5859-1. Specifications
9
Vehicle specifications
Light bulbs
Light bulbsBulb No.WTy p e
Exterior
HeadlightsLow beam (halogen bulbs)
*High beam
5565A B
Fog lights (halogen bulbs)*19C
Front turn signal lights7444NA28 /8D
Rear turn signal lightsWY21W21D
Back-up lightsW16W16E
Outer foot lightsW5W5E
Interior
Personal/interior lights5E
Rear interior lights8F
Vanity lights8E
Luggage compartment light5E
A: H11 halogen bulbs
B: H9 halogen bulbs
C: H16 halogen bulbs D: Wedge base bulbs (amber) E: Wedge base bulbs (clear)
F: Double end bulbs
*: If equipped