torque spec LEXUS ES300 2005 Repair Manual

A78386
8.0 (80, 71 in.Vlbf)
Ignition Coil Assy
Cylinder Head Cover
Sub-assy LH
8.4 (85, 74 in.Vlbf)
Engine Wire
Cylinder Head Cover Gasket No. 2
Camshaft Bearing Cap No. 2
16 (163, 12)
Camshaft Bearing Cap No. 2Camshaft Bearing Cap No. 3
Camshaft Bearing Cap No. 6
Camshaft Bearing Cap No. 5
Camshaft Timing Gear Assy
Camshaft Bearing Cap No. 4
Camshaft Timing Gear
Bolt WasherCamshaft Sub Gear
Wave Washer
Camshaft Sub GearCamshaft Sub Gear
Shaft Snap Ring
Camshaft Bearing Cap No. 2
150 (1,530, 111)
16 (163, 12)
Camshaft Bearing Cap No. 1
No. 4 Camshaft Sub-assy
Radiator Hose Inlet
N´m (kgf´cm, ft´lbf)
: Specified torque

Non-reusable part
Camshaft Setting
Oil Seal

V-bank Cover Sub-assy
8.0 (80, 71 in.Vlbf)
7.9 (81, 70 in.Vlbf)
No. 3 Camshaft
Sub-assy
x3
x9
x10
x10 14-106
- ENGINE MECHANICALCAMSHAFT (LH BANK) (3MZ-FE)
2198 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

141JG-01
A86358N´m (kgf´cm, ft´lbf) : Specified torque
7.9 (81, 70 in.Vlbf)x3
V-bank Cover Sub-assy
Mass Air Flow
Meter Connector Fuel Vapor Feed Hose
Assy
Vacuum Hose
Air Cleaner Cap
Sub-assy
Air Cleaner Filter
Element Sub-assy
5.0 (51, 44 in.Vlbf)
W/O TEMS:
Front Suspension Upper Brace Center
80 (816, 59)
Spacer
x2
Vacuum Hose
80 (816, 59)x2
Spacer
14-1 12
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
2204 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
CYLINDER HEAD GASKET (3MZ-FE)
COMPONENTS

A86260 Non-reusable part
: Specified torque VSV Connector
8.0 (82, 71 in.Vlbf)x2
Emission
Control Valve Set
Emission Control Valve Bracket
Intake Air Surge Tank
 Air Surge Tank
to Intake Manifold
Gasket
Throttle Motor Connector
Water By-pass Hose No. 3
Water By-pass Hose No. 2
N´m (kgf´cm, ft´lbf)
Union to Check Valve Hose
Fuel Vapor Feed Hose
x2 x3
Engine Hunger No. 1Surge Tank Stay
No. 1
Surge Tank Stay
No. 2
20 (199, 14)
20 (199, 14)
20 (199, 14)
7.8 (80, 69 in.Vlbf)
x2
x2 Pressure Feed
Tube Assy
28 (286, 21)
x2
x2
Bond Cable No. 1
Connector
28 (286, 21)
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
14-1 13
2205 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A86583 Non-reusable part
: Specified torqueN´m (kgf´cm, ft´lbf) Intake Manifold
to Head Gasket No. 2 Intake Manifold
to Head Gasket No. 1
Radiator Hose InletWater Outlet
Heater Inlet
Water Hose Intake Manifold Ground Cable
Washer
8.4 (86, 74 in.Vlbf)
x2x9
x2
Washer
15 (153, 11)
15 (153, 11)
Fuel Pipe
Clamp
15 (153, 11)
Fuel Injector
Connector
Clamp
Fuel Injector Connector
x2
Engine Coolant
Temperature Sensor
Connector
Bond Cable No. 1
Connector
Pipe
14-1 14
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
2206 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A84917
64 (653, 47)
64 (653, 47)
Front Fender Apron
Seal RH
Vane Pump V Belt
V Belt No. 1
Generator Bracket No. 2
Engine Mounting Stay No. 2 RHEngine Moving Control Rod
23 (235, 17)
58 (591, 43)
28 (286, 21)
N´m (kgf´cm, ft´lbf)
: Specified torque
Exhaust Pipe
Assy Front
Exhaust Pipe No. 1
Support Bracket Front
 Exhaust Pipe Gasket
 Non-reusable part
33 (337, 24)

56 (571, 41)
33 (337, 24)
Exhaust Pipe No. 1
Support Bracket Rear

 Exhaust Pipe
Gasket
 Exhaust Pipe Gasket
62 (633, 46)
62 (633, 46)
Radio Setting Condenser
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
14-1 15
2207 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A78383
N´m (kgf´cm, ft´lbf)
: Specified torque
8.5 (87, 75 in.Vlbf)
220 (2,250, 162)
8.5 (87, 75 in.Vlbf)
28 (286, 21)
27 (280, 20)
Timing Belt Tensioner Assy Crankshaft PulleyTiming Belt No. 1 Cover
Timing Belt Guide No. 2
Engine Mounting Bracket RH Timing Belt No. 2 Cover
Timing Belt
Engine Wire
Protector
14-1 16
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
2208 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A78384N´m (kgf´cm, ft´lbf)
: Specified torque
8.5 (87, 75 in.Vlbf)
43 (438, 32)
Timing Belt Idler
Sub-assy No. 2x6Timing Belt No. 3 Cover
CollarGasket
Bushing
Camshaft Timing Pulley
125 (1,275, 92)
Engine Wire
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
14-1 17
2209 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A84918
N´m (kgf´cm, ft´lbf)
: Specified torque
 Non-reusable part Exhaust Manifold to Head Gasket
43 (439, 32)
Exhaust Manifold Heat Insulator No. 1
Exhaust Manifold Sub-assy RH
Vane Pump Assy
43 (439, 32)
8.5 (87, 75 in.Vlbf)
49 (500, 36)
x3
x6 14-1 18
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
2210 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A78390
Camshaft Bearing Cap No. 2
Camshaft Bearing Cap No. 3
Camshaft Bearing Cap No. 6
Camshaft Bearing Cap No. 5
16 (163, 12)
x10
Camshaft
8.0 (80, 71 in.Vlbf)
8.4 (85, 74 in.Vlbf)
8.0 (80, 71 in.Vlbf)
16 (163, 12)
Ignition Coil AssyEngine Wire
Engine Wire
Cylinder Head Cover Gasket Cylinder Head Cover Sub-assy
Camshaft Bearing
Cap No. 2
x10Camshaft Bearing Cap No. 4
Camshaft Bearing Cap No. 2
No. 2 CamshaftCamshaft Bearing Cap No. 1
N´m (kgf´cm, ft´lbf)
: Specified torque
 Non-reusable part Camshaft Setting
Oil Seal 
19 (189, 14)
 Cylinder Head GasketCylinder Head Sub-assy
1st: 54 (550, 40)
2st: Turn 90
See page 14-120
x9
x8
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
14-1 19
2211 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)

A78721
Tension Portion
A78324
Front
A78717
1
2
3
4
5
67
8
Front
A78730
90
Front
Painted Mark 14-122
- ENGINE MECHANICALCYLINDER HEAD GASKET (3MZ-FE)
2214 Author
: Date
:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
40. INSPECT CYLINDER HEAD SET BOLT
(a) Using vernier calipers, measure the tension portion diam-
eter of the bolt.
Standard outside diameter:
8.95 to 9.05 mm (0.3524 to 0.3563 in.)
Minimum outside diameter: 8.75 mm (0.3445 in.)
If the diameter is less than minimum, replace the bolt.
41. INSTALL CYLINDER HEAD GASKET
(a) Place a new cylinder head gasket on the cylinder block
with the R mark upward.
NOTICE:

Remove any oil from the contact surface.

Be careful of the installing orientation.

Place the cylinder head on the gasket carefully in or-
der not to damage the gasket at the bottom part of the
head.
42. INSTALL CYLINDER HEAD SUB-ASSY
NOTICE:
The cylinder head bolts are tightened in 2 successive
steps.
(a) Apply a light coat of engine oil to the threads of the cylin-
der head bolts.
(b) Install the plate washers to the cylinder head bolts.
(c) Using several steps, install and tighten the 8 cylinder
head bolts uniformly in the sequence shown in the illustra-
tion.
Torque: 54 NVm (550 kgfVcm, 40 ftVlbf)
(d) Mark the front side of each cylinder head bolt head with
paint as shown in the illustration.
(e) Retighten the cylinder head bolts by 90in the same se-
quence as step (c).
(f) Check that each painted mark is now at a 90 angle to the
front.