display Lexus ES300h 2014 Navigation Manual

117
3. ADDRESS BOOK
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
3Select either or to adjust the di-
rection. Then select “OK”.
■TO CHANGE “Name”
1Select “Edit”.
2Enter the name usin g the alphanumeric
keys.
z Up to 70 characters can be entered.
3Select “OK”.
zThe previous screen will be displayed.
■ DISPLAYING ADDRESS BOOK
ENTRY NAMES
1Select “On” to display the name on the
map and select “Off” to not display it.
■TO CHANGE “Location”
1Select “Edit”.
2Select one of the 8 directional screen
buttons to move the cursor to the de-
sired point on the map.
3Select “OK”.
zThe previous screen will be displayed.
INFORMATION
●
The bell sounds only when the vehicle
approaches this point in the direction that
has been set.

118
3. ADDRESS BOOK
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
■TO CHANGE “Phone #”
(PHONE NUMBER)
1Select “Edit”.
2Enter the number using the number
keys.
3Select “OK”.
zThe previous screen will be displayed.
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Address Book” on the “Naviga-
tion Settings” screen.
4Select “Delete” .
5Select the address to be deleted.
6Select “Delete” .
7Select “Yes” to delete the address book
entries and select “No” to cancel the de-
letion.
DELETING ADDRESS BOOK
ENTRIES
Screen buttonFunction
“Select All”Select all registered ad-
dresses.
“Unselect All”Select to cancel the
“Select All” function.

120
3. ADDRESS BOOK
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
5Select the desired screen button and
enter the location in the same way as for
a destination search, or display the map
of the area to be avoided. (See “DESTI-
NATION SEARCH” on page 68.)
6Scroll the map to the desired point.
“A d j u s t L o c a t i o n ” : Select to adjust the posi-
tion in smaller increments.
7Select “Enter”.
8Select either or to change the
size of the area to be avoided.
9Select “OK”.
zWhen registration of an area to avoid is
completed, the “Area to Avoid” screen will
be displayed.
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “A r e a s t o A v o i d ” on the “Naviga-
tion Settings” screen.
4Select “Edit”.
5Select the area to be avoided.
INFORMATION
●
If a destination is input in the area to avoid
or the route calculation cannot be made
without running through the area to
avoid, a route passing through the area to
be avoided may be shown.
●Up to 10 locations can be registered as
points/areas to avoid.
EDITING AREA TO AVOID
The name, location and/or area size of a
registered area can be edited.

121
3. ADDRESS BOOK
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
6Select “Edit” next to the item to be edit-
ed.
“Show Name on Map”:
The name of an area to
be avoided can be set to be displayed on the
map by selecting “On” or “Off ” .
(See page
121.)
“Active”: The area to avoid feature can be
set to “On” or “Off” .
7Select “OK”.
■TO CHANGE “Name”
1Select “Edit”.
2Enter the name usin g the alphanumeric
keys.
z Up to 70 characters can be entered.
3Select “OK”.
zThe previous screen will be displayed.
■ DISPLAYING NAMES OF AREAS
TO BE AVOIDED
1Select “On”, next to “Show Name on
Map”, to display the name of an area to
be avoided on the map. Select “Off ” not
to display it.
No.FunctionPage
Select to edit the name of
the area to avoid. The name
can be displayed on the
map.
121
Select to edit area location.122
Select to edit area size.122

122
3. ADDRESS BOOK
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
■TO CHANGE “Location”
1Select “Edit”.
2Select one of the 8 directional screen
buttons to move the cursor to the de-
sired point on the map.
3Select “OK”.
zThe previous screen will be displayed.
■ TO CHANGE “Size”
1Select “Edit”.
2Select either or to change the
size of the area to be avoided.
3Select “OK”.
zThe previous screen will be displayed.

126
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
zTo reset all setup items, select “Default”.
No.Function
Select to set the average cruising
speed. (See “DRIVING SPEEDS”
on page 127.)
Select to set the automatic input
function to “On” or “Off” .
Select to set the voice guidance for
the next street name to “On” or
“Off” during route guidance.
Select to set the automatic reroute of
the guidance route to avoid heavy
congestion to “On” or “Off” . (See
“AUTO AVOID TRAFFIC” on page
127.)
Select to set the indication of freely
flowing traffic by the arrow to “On”
or “Off” . (See “SHOW FREE
FLOWING TRAFFIC” on page
128.)
Select to set displayed POI icon cat-
egories. (See “POI CATEGORY
CHANGE (SELECT POI ICONS)”
on page 129.)
Select to set screen buttons to be
displayed on the map screen when
“ WW Off” is selected. (See
“SCREEN LAYOUT FUNCTION
(“ WW Off” Function)” on page 130.)
Select to adjust the current position
mark manually. Mis calculation of the
distance caused by tire replacement
can also be adjusted. (See “CUR-
RENT POSITION/TIRE CHANGE
CALIBRATION” on page 130.)
Select to set the display of pop-up in-
formation to “On” or “Off” . (See
“POP-UP INFORMATION” on
page 132.)
Select to set IPD road guidance to
“On” or “Off ” . (For information on
IPD roads, see page 95.)
No.Function

127
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select “Driving Speeds” .
5Select “” or “” to set the average ve-
hicle speeds for “Residential”, “Main
Streets” and “Freeways”.
z To set the default speeds, select “Default”.
z To use settings based on traffic information,
select “Consider Traffic Info.” .
6After setting of the desired speeds is
completed, select “Save”.
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select “A v o i d Tr a f f i c ” .
DRIVING SPEEDS
The speed that is used for the calculation
of the estimated travel time and estimat-
ed arrival time can be set.
INFORMATION
●
The displayed time to the destination is
the approximate driving time that is cal-
culated based on the selected speeds
and the actual position along the guid-
ance route.
●The time shown on the screen may vary
greatly depending on progress along the
route, which may be affected by condi-
tions such as traffic jams and construction
work.
●Up to 99 hours 59 minutes can be dis-
played.
AUTO AVOID TRAFFIC
The guidance route automatically
changes to another route to avoid heavy
congestion when “Avoid Traffic” is
turned on.

129
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select “Favorite POI Categories” .
5Select the category to be changed.
6Select the desired group.
zIf the desired POI category is not on the
screen, select “List All Categories” to list
all POI categories.
7Select the desired category.
z The screen returns to the “Favorite POI
Categories” screen.
8Select “OK”.
POI CATEGORY CHANGE
(SELECT POI ICONS)
Select up to 6 POI icons to be displayed
on the map screen.

130
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select ““WW Off” Function” .
5Select the screen buttons to be turned
off. The selected screen buttons will be
dimmed.
zTo set the setting as a default, select
“Default”.
6Select “OK”.
zThe previous screen will be displayed.
7Select “Save” .
1Press the “MENU” button on the
Remote Touch, then select “Setup”.
2Select “Navigation” on the “Setup”
screen.
3Select “Detailed Navi. Settings” on the
“Navigation Settings” screen.
4Select “Calibration” .
5Select the desired screen button.
SCREEN LAYOUT FUNCTION
(“WW Off” Function)
Each screen button and current street
name on the map screen can be dis-
played or hidden.CURRENT POSITION/TIRE
CHANGE CALIBRATION
The current position mark can be adjust-
ed manually. Miscalculation of the dis-
tance caused by tire replacement can
also be adjusted.
z For additional information on the accu-
racy of a current position, see “LIMITA-
TIONS OF THE NAVIGATION
SYSTEM” on page 139.

131
4. SETUP
ES350/300h_Navi_OM33A66U_(U)13.07.11 10:10
3
NAVIGATION SYSTEM
■POSITION/DIRECTION CALI-
BRATION
1Select “Position / Direction” .
2Select one of the 8 directional screen
buttons to move the cursor to the de-
sired point on the map.
3Select “OK”.
4Select either or to adjust the di-
rection of the current position mark.
5Select “OK”.
zThe map will be displayed.
■ TIRE CHANGE CALIBRATION
1To perform the distance calibration pro-
cedure, select “Tire Change” .
zThe message appears and the quick dis-
tance calibration is automatically started. A
few seconds later, a map will be displayed.
When driving, the cu rrent position mark
will be automatically corrected by GPS
signals. If GPS reception is poor due to
location, the current position mark can
be adjusted manually.
The tire change calibration function will
be used when replacing the tires. This
function will adjust miscalculation
caused by the circumference difference
between the old and new tires.