sensor LEXUS GS400 2000 Service User Guide

D01038
Shift Control Rod
Heat Insulator
Heated Oxygen Sensor
Front Exhaust Pipe Front Exhaust Pipe
Heated Oxygen Sensor Heated Oxygen Sensor
Gasket
13 (130, 9)
5.4 (55, 48 in.´lbf)
44 (450, 33)

Gasket

Gasket

Gasket

Gasket
2JZ±GE Engine:
1UZ±FE Engine:
N´m (kgf´cm, ft´lbf): Specified torque

Non±reusable partx6
44 (450, 33)
44 (450, 33)
44 (450, 33)
44 (450, 33)
44 (450, 33)
44 (450, 33)44 (450, 33)






44 (450, 33)
44 (450, 33)


44 (450, 33)
44 (450, 33)






44 (450, 33)
44 (450, 33)
AT±14
± AUTOMATIC TRANSMISSIONFLOOR SHIFT ASSEMBLY
1962 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)

AT067±01
D01040

Gasket
Clamp
ClampAir Cleaner, MAF Meter and Intake
Air Connector Pipe Assembly
Exhaust Manifold with TWC
Connector and
Wire Harness Level Gauge
Filler PipeAdjusting WasherPropeller Shaft Assembly
Shift Control Rod
Torque Converter ClutchPlug for Line
Pressure TestHeat Insulator
Heated Oxygen Sensor
Front and Center
Exhaust PipeFront Floor
Center Brace
Engine Under Cover Pipe Support BracketO±Ring Heat Insulator

Gasket
Starterx6x839 (400, 29)
44 (450, 33)
72 (730, 53)
37 (380, 27)
13 (130, 9)
79 (805, 58)
37 (375, 27)
7.4 (75, 65 in.´lbf)
44 (450, 33)
44 (450, 33)
37 (380, 27)
37 (380, 27)
Hole Plug
5.4 (55, 48 in.´lbf)
Oil Cooler Pipe
x5

O±Ring
5.4 (55, 48 in.´lbf)

Gasket
44 (450, 33)


5.4 (55, 48 in.´lbf)
N´m (kgf´cm,ft´lbf) : Specified torque

Non±reusable part
Gasket
48 (490, 35)
26 (270, 20)
44 (450, 33)
44 (450, 33)


79 (805, 58)
± AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (2JZ±GE)
AT±27
1975 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
AUTOMATIC TRANSMISSION UNIT (2JZ±GE)
COMPONENTS

AT068±01
D01041
D01042
AT±28
± AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (2JZ±GE)
1976 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE LEVEL GAUGE
2. REMOVE FILLER PIPE
Remove the bolt and filler pipe with the O±ring.
HINT:
At the time of installation, please refer to the following item.
Replace the used O±ring with a new one.
3. REMOVE AIR CLEANER, MAF METER AND INTAKE
AIR CONNECTOR PIPE ASSEMBLY
4. REMOVE EXHAUST MANIFOLD WITH TWC
Remove the 8 nuts, 2 gaskets and exhaust manifold with the
TWC.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Replace the used gaskets with new ones.
5. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
6. REMOVE ENGINE UNDER COVER
7. REMOVE FRONT AND CENTER EXHAUST PIPE
(a) Disconnect the heated oxygen sensor.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
HINT:
At the time of installation, please refer to the following items.

Before installing the heated oxygen sensor, twist the sen-
sor wire counterclockwise 3 and 1/2 turns.

After installing the heated oxygen sensor wire should not
twist. If it is twisted, remove the heated oxygen sensor
and reinstall it.
(b) Remove the 2 bolts and front floor center brace.
Torque: 7.4 N´m (75 kgf´cm, 65 in.´lbf)
(c) Remove the 3 bolts, nuts and 2 gaskets.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Replace the used nuts and gaskets with new ones.
(d) Remove the 2 bolts and pipe support bracket.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)

D01047
Q03721
D01048
Q06925
AT±30
± AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (2JZ±GE)
1978 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
12. REMOVE TORQUE CONVERTER CLUTCH MOUNT-
ING BOLT
(a) Remove the hole plug.
(b) Turn the crankshaft to gain access to each bolt.
(c) Hold the crankshaft pulley nut with a wrench and remove
the 6 bolts.
Torque: 48 N´m (490 kgf´cm, 35 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
First install black colored bolt and then the 5 other bolts.
13. SUPPORT TRANSMISSION WITH JACK
14. REMOVE 4 ENGINE REAR MOUNTING SET BOLTS
Torque: 26 N´m (270 kgf´cm, 20 ft´lbf)
15. DISCONNECT CONNECTORS AND WIRE HARNESS
(a) Tilt down the transmission.
NOTICE:
Take care so that the cooling fan does not come in contact
with the fan shroud.
(b) Disconnect the following connectors:
(1) O/D direct clutch speed sensor connector
(2) Vehicle speed sensor connector
(3) Park/neutral position switch connector
(4) Solenoid connector
(c) Disconnect the wire harness from the clamp on the trans-
mission.

AT06A±01
D01049
Oil Cooler Pipe
Connector and Wire Harness
Level Gauge
Torque Converter Clutch
Flywheel Housing
Under CoverPlug for Line
Pressure Test
Front and Center Exhaust PipePropeller Shaft Assembly
Heated Oxygen Sensor
Pipe Support BracketRH Front TWC
Engine Under CoverHeat Insulator
Ground CableHeat Insulator
GasketO±Ring x6Adjusting Washer
Filler Pipe
44 (450, 33)
79 (805, 58)
37 (375, 27)
79 (805, 58)
13 (130, 9)
37 (380, 27)
18 (185, 13)
44 (450, 33)
44 (450, 33)
62 (630, 46)
62 (630, 46)
72 (730, 53)
37 (380, 27)
48 (490, 35)
44 (450, 33)44 (450, 33)
5.4 (55, 48 in.´lbf)
5.4 (55, 48 in.´lbf)
Heat Insulator
26 (270, 20)

Gasket
LH Front TWC
44 (450, 33)

Gasket

Gasket


















N´m (kgf´cm, ft´lbf) : Specified torque
Non±reusable part
Heat Insulator
5.4 (55, 48 in.´lbf)
44 (450, 33)
44 (450, 33)

O±Ring
Heated Oxygen
SensorFront Floor
Center Brace
7.4 (75, 65 in.´lbf)
x6
± AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (1UZ±FE)
AT±33
1981 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
AUTOMATIC TRANSMISSION UNIT (1UZ±FE)
COMPONENTS

AT06B±01
D01050
D01051
D00999
AT±34
± AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (1UZ±FE)
1982 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REMOVAL
1. REMOVE LEVEL GAUGE
2. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
3. REMOVE ENGINE UNDER COVER
4. REMOVE FRONT AND CENTER EXHAUST PIPES
(a) Disconnect he 2 heated oxygen sensor.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
HINT:
At the time of installation, please refer to the following items.

Before installing the heated oxygen sensor, twist the sen-
sor wire counterclockwise 3 and 1/2 turns.

After installing the heated oxygen sensor wire should not
twist. If it is twisted, remove the heated oxygen sensor
and reinstall it.
(b) Remove the 2 bolts and front floor center brace.
Torque: 7.4 N´m (75 kgf´cm, 65 in.´lbf)
(c) Remove the 4 bolts, nuts and 2 gaskets from the LH and
RH front TWC.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Replace the used nuts and gaskets with new ones.
(d) Remove the 2 bolts and support bracket.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
(e) Remove the 4 bolts and 2 gaskets from the tail pipe.
Torque: 44 N´m (450 kgf´cm, 33 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Replace the used gaskets with new ones.
(f) Disconnect the front and center exhaust pipes from the 2
O±rings and remove them.
5. REMOVE LH AND RH FRONT TWC
Remove the 6 nuts, 2 gaskets, LH and RH front TWC.
Torque: 62 N´m (630 kgf´cm, 46 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Replace the used nuts and gaskets with new ones.

D01005
Q03721
D01048
Q06925
AT±36
± AUTOMATIC TRANSMISSIONAUTOMATIC TRANSMISSION UNIT (1UZ±FE)
1984 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(b) Turn the crankshaft to gain access to each bolt.
(c) Hold the crankshaft pulley nut with a wrench and remove
the 6 bolts.
Torque: 48 N´m (490 kgf´cm, 35 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
First install the black colored bolt and then the 5 other bolts.
12. SUPPORT TRANSMISSION WITH JACK
13. REMOVE 4 ENGINE REAR MOUNTING SET BOLTS
Torque: 26 N´m (270 kgf´cm, 20 ft´lbf)
14. DISCONNECT CONNECTORS AND WIRE HARNESS
(a) Tilt down the transmission.
NOTICE:
Take care so that the cooling fan does not come in contact
with the fan shroud.
(b) Disconnect the following connectors:
(1) O/D direct clutch speed sensor connector
(2) Vehicle speed sensor connector
(3) Park/neutral position switch connector
(4) Solenoid connector
(c) Disconnect the wire harness from the clamp on the trans-
mission.

AT05Y±01
D00910
Q07487
SST
AT0103
± AUTOMATIC TRANSMISSIONATF TEMPERATURE SENSOR
AT±5
1953 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
ATF TEMPERATURE SENSOR
ON±VEHICLE REPAIR
CAUTION:
When working with FIPG material, you must observe the follow-
ing items.

Using a razor blade and gasket scraper, remove all the old
FIPG material from the gasket surfaces.

Thoroughly clean all components to remove all the loose
material.

Clean both sealing surfaces with a non±residue solvent.

Apply FIPG in an approx. 1 mm (0.04 in.) wide bead along
the sealing surface.

Parts must be assembled within 10 minutes of application.
Otherwise, the FIPG material must be removed and reap-
plied.
1. REMOVE DRAIN PLUG WITH GASKET AND DRAIN
AT F
2. REMOVE OIL PAN
NOTICE:
Some fluid will remain in the oil pan.
(a) Remove the 19 bolts.
(b) Install the blade of SST between the transmission case
and oil pan, cut off applied sealer, and remove the oil pan.
SST 09032±00100
NOTICE:
When removing the oil pan, be careful not to damage the oil
pan flange.
3. EXAMINE PARTICLES IN PAN
Remove the magnets and use them to collect steel particles.
Carefully look at the foreign matter and particles in the pan and
on the magnets to anticipate the type of wear you will find in the
transmission.
Steel (magnetic) ... bearing, gear and clutch plate wear
Brass (non±magnetic) ... bushing wear

D00752
D00753
D00909
D00916
D00909
AT±6
± AUTOMATIC TRANSMISSIONATF TEMPERATURE SENSOR
1954 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
4. REMOVE OIL STRAINER
NOTICE:
Be careful as some fluid will come out of the oil strainer.
(a) Remove the 4 bolts and oil strainer.
(b) Remove the 3 gaskets from the oil strainer.
5. REMOVE SOLENOID WIRING WITH ATF TEMPERA-
TURE SENSOR
(a) Disconnect the ATF temperature sensor.
(b) Remove the bolt and clamp.
(c) Disconnect the 7 connectors from the solenoid valves.
(d) Remove the bolt and pull out the solenoid connector.
6. INSTALL SOLENOID WIRING WITH ATF TEMPERA-
TURE SENSOR
(a) Install the solenoid connector with the bolt.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Connect the 7 connectors to the solenoid valves.
(c) Install the clamp with the bolt.
Torque: 6.4 N´m (65 kgf´cm, 56 in.´lbf)
(d) Connect the ATF temperature sensor.

D00753
D00752
D00912
D01917
Seal Breadth 2 ~ 3 mm (0.08 ~ 0.12 in.)
D00910
ºAº
± AUTOMATIC TRANSMISSIONATF TEMPERATURE SENSOR
AT±7
1955 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
7. INSTALL OIL STRAINER
(a) Install 3 new gaskets.
(b) Install the oil strainer with the 4 bolts.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
8. INSTALL OIL PAN
(a) Install the 3 magnets in the indications of the oil pan.
(b) Remove any packing material and be careful not to drop
oil on the contacting surfaces of the transmission case
and oil pan.
(c) Apply FIPG to the oil pan.
FIPG:
Part No. 08826 ± 00090, THREE BOND 1281 or
equivalent
(d) Install the oil pan with the 19 bolts.
Torque: 7.4 N´m (75 kgf´cm, 65 in.´lbf)
HINT:
Replace the only ºAº bolt with a new one.
9. INSTALL DRAIN PLUG WITH NEW GASKET
Torque: 20 N´m (205 kgf´cm, 15 ft´lbf)
10. FILL FLUID AND CHECK FLUID
(See page DI±318)