lexus LC500 2018 Owner's Manual

141
3
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
Before driving
will be overwritten.
■Seat positions that can be memorized
( P.138)
The adjusted positions other than the posi-
tion adjusted by lumbar support switch can be recorded.
■In order to correctly use the driving position memory function
If a seat position is already in the furthest possible position and the seat is operated in
the same direction, the recorded position may be slightly different when it is recalled.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Check that the shift position is in P.
3 Press one of the buttons for the
driving position you want to recall
until the buzzer sounds.
■To stop the position recall operation
part-way through
Perform any of the following:
●Press the “SET” button.
●Press button “1”, “2” or “3”.
●Operate any of the seat adjustment
switches (only cancels seat position recall).
●Operate the tilt and telescopic steering control switch (only cancels steering
wheel position recall).
■Operating the driving position memory after turning the engine switch off
Recorded seat positions can be activated up to 180 seconds after the driver’s door is
opened and another 60 seconds after it is closed again.
■Registering procedure
Record your driving position to button
“1”, “2” or “3” before performing the
following:
WARNING
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passen-
ger or squeeze your body against the steering wheel.
Recalling a driving position
Registering/cancel ing/recalling
a driving position to an elec-
tronic key (memor y recall func-
tion)

142
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
Carry only the key you want to register,
and then close the driver’s door.
If 2 or more keys are in the vehicle, the
driving position cannot be recorded
properly.
1 Turn the engine switch switch> to IGNITION ON mode
.
2 Check that the shift position is in P.
3 Recall the driving position that you
want to record.
4 While pressing the recalled button,
press and hold the door lock switch
(either lock or unlock) until the
buzzer sounds.
If the button could not be registered, the buzzer sounds continuously for approxi-mately 3 seconds.
■Cancelation procedure
1 Carry only the key you want to can-
cel and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be canceled prop-erly.
2 Turn the engine switch switch> to IGNITION ON mode
.
3 While pressing the “SET” button,
press and hold the door lock switch
(either lock or unlock) until the
buzzer sounds twice.
If the button could not be canceled, the buzzer sounds continuously for approxi-
mately 3 seconds.
■Recall procedure
1 Make sure that the doors are
locked before recalling the driving
position. Carry the electronic key
that has been registered to the driv-
ing position, and then unlock and
open the driver’s door using the
smart entry & start system or wire-
less remote control.
The driving position will move to the recorded position (not including the steer-
ing wheel and head-up display).
If the driving position is in a position that
has already been recorded, the seat and outside rear view mirrors will not move.
2 Turn the engine switch switch> to ACCESSORY mode or
IGNITION ON mode mode>.
The steering wheel and head-up display will move to the recorded position.
■Recalling the driving position using the
memory recall function
●Different driving positions can be regis-
tered for each electronic key. Therefore, the driving position that is recalled may be different depending on the key being
carried.
●If the passenger’s door is unlocked with
the smart entry & start system, the driving position cannot be recalled. In this case, press the driving position button which
has been set.
■Customization
The unlock door settings of the memory
recall function can be changed. (Customizable features: P.423)

143
3
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
Before driving
Manual type
1 Up
Pull the head restraints up.
2Down
Push the head restraint down while press-
ing the lock release button .
Power type
1 Up
2 Down
■Adjusting the height of the head restraints
Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.
Pull the head restraint up while press-
ing the lock release button .
If the head restraint touches the ceiling,
making the removal difficult, change
the seat height or angle. ( P.138)
Head restraints
Head restraints are provided for
front seats.
WARNING
■Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious
injury.
●Adjust the head restraints to the cor- rect position at all times.
●Manual type: After adjusting the head restraints, push down on them and
make sure they are locked in position.
●Manual type: Do not drive with the head restraints removed.
Vertical adjustment
A
Removing the head restraints
(manual type only)
A

144
-$@-$I@0.@0.&@ &&

3-3. Adjusting the seats
■Removing the head restraints (power type only)
For removing and installation of the head restraint, contact any authorized Lexus retailer or Lexus authorized repairer, or any
reliable repairer.
Align the head restraint with the instal-
lation holes and push it down to the
lock position.
Press and hold the lock release button
when lowering the head restraint.
Installing the head restraints
(manual type only)
A

145
3
-$@-$I@0.@0.&@ &&

3-4. Adjusting the steering wheel and mirrors
Before driving
3-4.Adjusting the stee ring wheel and mirro rs
Operating the switch moves the steer-
ing wheel in the following directions:
1 Up
2 Down
3 Toward the driver
4 Away from the driver
■The steering wheel can be adjusted when
The engine switch

is in ACCESSORY or IGNITION ON mode .
■Automatic adjustment of the steering
position
A desired steering position can be entered
to memory and recalled automatically by the driving position memory system. ( P.140)
■Enabling easier driver entry and exit
(auto tilt away)
When the engine switch is
turned off, the steering wheel returns to its stowed position by moving up and away.
Turning the engine swit ch to
ACCESSORY or IGNITION ON mode
will return the steering wheel
to the original position.
■Customization
The auto tilt away function can be changed.
(Customizable features: P.423)
Press on or close to the mark.
Steering wheel
Adjustment procedure
WARNING
■Caution while driving
Do not adjust the steering wheel while driving.
Doing so may cause the driver to mis- handle the vehicle and cause an acci-dent, resulting in death or serious injury.
Sounding the horn

146
-$@-$I@0.@0.&@ &&

3-4. Adjusting the steering wheel and mirrors
The height of the rear view mirror can
be adjusted to suit your driving pos-
ture.
Adjust the height of the rear view mir-
ror by moving it up and down.
Responding to the level of brightness
of the headlights of vehicles behind, the
reflected light is automatically
reduced.
Turn the automatic anti-glare function
mode on/off
When the automatic anti-glare function is
in ON mode, the indicator illuminates.
The function will set to ON mode each
time the engine switch is
turned to IGNITION ON mode mode>.
Pressing the button turns the function to
OFF mode. (The indicator also turns
off.)
■To prevent sensor error
To ensure that the sensors operate properly, do not touch or cover them.
Inside rear view mirror
The rear view mirror’s position can
be adjusted to enable sufficient
confirmation of the rear view.
Adjusting the height of rear view
mirror
WARNING
■Caution while driving
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.
Anti-glare function
A
A

147
3
-$@-$I@0.@0.&@ &&

3-4. Adjusting the steering wheel and mirrors
Before driving
1To select a mirror to adjust, press
the switch.
The indicator comes on.
Left
Right
Pressing the same switch again will put the
switch in neutral.
2 To adjust the mirror, press the
switch.
Up
Right
Down
Left
■Mirror angle can be adjusted when
The engine switch

is in ACCESSORY or IGNITION ON mode .
■Defogging the mirrors
The outside rear view mirrors can be cleared using the mirror defoggers. Turn on
the rear window defogger to turn on the outside rear view mirror defoggers. ( P.281)
■Auto anti-glare function
When the anti-glare inside rear view mirror is set to automatic mode, the outside rear
view mirrors will activate in conjunction with the anti-glare inside rear view mirror to reduce reflected light. ( P.146)
■Automatic adjustment of the mirror
angle
A desired mirror face angle can be entered
to memory and recalled automatically by the driving position memory. ( P.140)
Outside rear view mirrors
The rear view mirror’s position can
be adjusted to enable sufficient
confirmation of the rear view.
WARNING
■Important points while driving
Observe the following precautions while
driving. Failure to do so may result in loss of con-trol of the vehicle and cause an accident,
resulting in death or serious injury.
●Do not adjust the mirrors while driving.
●Do not drive with the mirrors folded.
●Both the driver and passenger side mirrors must be extended and prop-erly adjusted before driving.
Adjustment procedure
A
B
A
B
C
D

148
-$@-$I@0.@0.&@ &&

3-4. Adjusting the steering wheel and mirrors
■Using the switch
Press the switch to fold the mirrors.
Press it again to extend them to the original
position.
■Setting automatic mode
Automatic mode allows the folding or
extending of the mirrors to be linked to
locking/unlocking of the doors.
Press the “AUTO” switch to set auto-
matic mode.
The indicator will come on.
Pressing the switch on ce more will return
to manual mode.
■When disconnecting and reconnecting 12-volt battery terminals
The automatic folding/extending mirror function will return to off as default. To turn the function on, press the switch again to
select on.
■Using automatic mode in cold weather
When automatic mode is used in cold
weather, the door mirror could freeze up and automatic stowing and return may not be possible. In this case, remove any ice and
snow from the door mirror, then either operate the mirror using manual mode or move the mirror by hand.
■Customization
The automatic mirror folding and extending operation can be changed.
(Customizable features: P.423)
When either “L” or “R” of the mirror
select switch is selected, the outside
rear view mirrors will automatically
angle downwards when the vehicle is
reversing in order to give a better view
WARNING
■When the outside rear view mirror defoggers are operating
Do not touch the outside rear view mir- ror surfaces, as they can become very hot and burn you.
Folding and extending the mir-
rors
A
WARNING
■When a mirror is moving
To avoid personal injury and mirror mal- function, be careful not to get your hand caught by the moving mirror.
Linked mirror function when
reversing

149
3
-$@-$I@0.@0.&@ &&

3-4. Adjusting the steering wheel and mirrors
Before driving
of the ground.
To disable this function, select neither
“L” nor “R”.
■Adjusting the mirror angle when
the vehicle is reversing
With the shift position in R, adjust the
mirror angle at a desired position.
The adjusted angle will be memorized
and the mirror will automatically tilt to
the memorized angle whenever the
shift position is shifted to R from next
time.
The memorized downward tilt position of
the mirror is linked to the normal position
(angle adjusted with the shift position in
other than R). Therefore, if the normal posi-
tion is changed after adjustment, the tilt
position will also change.
When the normal position is changed,
readjust the angle in reversing.

150
-$@-$I@0.@0.&@ &&

3-5. Opening, closing the windows
3-5.Opening, closing the windows
The power windows can be opened
and closed by one-touch operation of
the switches.
1 Closing
2 One-touch closing*
3Opening
4 One-touch opening*
*: To stop the window partway, operate the
switch in the opposite direction.
■The power windows can be operated
when
The engine switch

is in
IGNITION ON mode .
■Operating the power windows after turning the engine off
The power windows can be operated for approximately 45 seconds after the engine switch is turned to ACCES-
SORY mode or turned off. They cannot, however, be operated once either door is opened.
■Jam protection function
If an object becomes jammed between the window and the window frame while the
window is closing, window movement is
stopped and the window is opened slightly.
■Catch protection function
If an object becomes caught between the
door and window while the window is open- ing, window movement is stopped.
■When the window cannot be opened or closed
When the jam protection function or catch protection function operates unusually and
the door window cannot be opened or closed, perform the following operations with the power window switch of that door.
●Stop the vehicle. With the engine switch in IGNITION ON mode
, within 4 seconds of the jam protection function or catch protection function activating, continuously operate
the power window switch in the one- touch closing direction or one-touch opening direction so that the door win-
dow can be opened and closed.
●If the door window cannot be opened
and closed even when performing the above operations, perform the following procedure for function initialization.
1 Close both side doors.
2 Turn the engine switch to IGNITION ON mode .
3 Pull and hold the power window switch in the one-touch cl osing direction and
completely close the door window.
4 Release the power window switch for a moment, resume pulling the switch in the one-touch closing direction, and
hold it there for approximately 6 sec- onds or more.
5 Press and hold the power window switch in the one-touch opening direc-
tion. After the door window is com- pletely opened, continue holding the switch for an additional 1 second or
more.
6 Release the power window switch for a moment, resume pushing the switch in the one-touch opening direction, and
hold it there for approximately 4 sec- onds or more.
7 Pull and hold the power window switch in the one-touch closing direction
Power windows
Opening and closing the power
windows