torque LEXUS SC400 1991 Service Owners Manual

SERVICE SPECIFICATIONS
SERVICE DATA
BatterySpecific gravity1.27±1.29
(when fully charged at 205C (68 5F))
AlternatorRated output12 V±100 A
Rotor coil resistance2.8±3.0

Slip ring diameterSTD 14.2±14.4 mm0.559±0567 in.
Limit 12.8 mm0.504 in.
Brush exposed lengthSTD 10.5 mm0.413 in.
Limit 1.5 mm0.059 in.
AlternatorRegulating voltageat 255C (77 5F)13.9±15.1 V
regulatorat 115 5C (239 5F)13.5±14.3 V
TORQUE SPECIFICATIONS
Part tightenedN Vmkgf Vcmft Vlbf
Alternator pulley X Rotor11 01,12581
Alternator X Alternator bracket37380 27
Alternator X Cylinder block3738027
±
CHARGING SYSTEM Service SpecificationsCH±21
WhereEverybodyKnowsYourName

PREPARATION
SST (SPECIAL SERVICE TOOLS)
09285±76010
Injection Pump
Camshaft Bearing
Cone ReplacerRotor rear bearing
09286±46011Injection Pump
Spline Shaft PullerRectifier end frame
09608±20012
Front Hub & Drive
Pinion Bearing Tool
Set
(09608±00030)
(Replacer)
Rotor front bearing
09820±00021Alternator Rear
Bearing Puller
09820±00030Alternator Rear
Bearing Replacer
09820±63010Alternator Pulley Set
Nut Wrench Set
RECOMMENDED TOOLS
09082±00015TOYOTA
Electrical Tester
09200±00010Engine Adjust
Kit
EQUIPMENT Part Name\
 \
Note Battery specific gravity gauge\
 \
Battery Vernier caliper\
 \
Rotor (Slip ring) Torque wrench\
 \

CH±4±
CHARGING SYSTEM Preperation
WhereEverybodyKnowsYourName

(c) Remove the seal plate.
4. REMOVE PULLEY (a) Hold SST (A) with a torque wrench, and tighten SST (B)clockwise to the specified torque.
SST 09820±63010
Torque: 39 N Vm (400 kgf Vcm, 29 ft Vlbf)
(b) Check that SST (A) is secured to the rotor shaft.
(c) As shown in the illustration, mount SST (C) in a vise, and
install the alternator to SST (C).
(d) To loosen the pulley nut, turn SST (A) in the direction
shown in the illustration.
NOTICE: To prevent damage to the rotor shaft, do not
loosen the pulley nut more than one±half of a turn.
(e) Remove the alternator from SST (C).
(f) Turn SST (B) and remove SST (A and B).
(g) Remove the pulley nut and pulley.
5. REMOVE RECTIFIER END FRAME (a) Remove the four mounting nuts.
(b) Using SST, remove the rectifier end frame.
SST 09286±46011
CH±12
±
CHARGING SYSTEM Alternator
WhereEverybodyKnowsYourName

4. INSTALL PULLEY(a) Install the pulley to the rotor shaft by tightening thepulley nut by hand.
(b) Hold SST (A) with a torque wrench, and tighten SST (B)
clockwise to the specified torque.
SST 09820±63010
Torque: 39 N Vm (400 kgf Vcm, 29 ft Vlbf)
(c) Check that SST (A) is secured to the pulley shaft.
(d) As shown in the illustration, mount SST (C) in a vise, and
install the alternator to SST (C).
(e) To torque the pulley nut, turn SST (A) in the direction shown in the illustration.
Torque: 110 N Vm (1,125 kgf Vcm, 81 ft Vlbf)
(f) Remove the alternator from SST (C).
(g) Turn SST (B) and remove SST (A and B).
5. INSTALL RECTIFIER HOLDER (a) Place the seal plate on the rectifier end frame.
(b) Install the four rubber insulators on the lead wires.
(c) Install the rectifier holder with the four screws.
CH±18
±
CHARGING SYSTEM Alternator
WhereEverybodyKnowsYourName

INSTALLATION OF ALTERNATOR
(See Components on page CH±9)
1. INSTALL ALTERNATOR (a) Install the alternator and A/T oil cooler bracket with the
bolt and nut.
Torque: 37 N Vm (380 kgf Vcm, 27 ft Vlbf)
(b) Connect the alternator connector.
(c) Connect the alternator wire with the nut and cap.
2. INSTALL DRIVE BELT Install the drive belt by turning the drive belt tensioner coun-
terclockwise.
HINT: The pulley bolt for the belt tensioner has a left±hand
thread.
3. CONNECT CABLE TO NEGATIVE TERMINAL OF BATTERY
4. PERFORM ON±VEHICLE INSPECTION (See steps 6 to 8 on pages CH±6 to 8)
5. INSTALL ENGINE UNDER COVER
CH±20
±
CHARGING SYSTEM Alternator
WhereEverybodyKnowsYourName

REFERENCE:
HIGH-STRENGTH STEEL (HSS) PARTS
Generally, High-Strength Steel (HSS) is that which has an intensity value of at\
least 35 kgf/mm2 (343 MPa),
and distinguished from mild steel.
The handling of HSS is the same as for mild steel, but the following sho\
uld be observed.
1. Panel Hammering: Because HSS is thinner than mild steel, care should be \
taken to avoid warping during hammering operations.
2. Removing Spot Welds: Because HSS is tougher than mild steel, damage will occur more eas\
ily to a regular drill. Therefore, an HSS Spot Cutter is recommended.
Also, use a high-torque drill at low speed, and supply grinding oil to t\
he drill during use.
3. Panel Welding: Panel welding procedures for HSS are exactly the same as for mil\
d steel. Plug welding should be done with a MIG (Metal Inert Gas) welder. Do not gas weld or braze panels at
areas other than specified.
BODY PANEL CONSTRUCTIONCN-3
WhereEverybodyKnowsYourName

SERVICE SPECIFICATIONS
SERVICE DATA
ThermostatValve opening temperature80±845C176±183 5F
Valve liftat 95 5C (203 5F) 10 mm0.39 in.
Radiator capRelief valve opening pressureSTD74±103 kPa
(0.75±1.05 kgf/cm, 10.7±14.9 psi)
Limit 59 kPa 0.6 kgf/cm 8.5 psi
On±vehicle
itifh
Oil pressure1,177±2,452 kPa
inspection for hy-
draulic cooling(12±25 kgf/cm, 171±356 psi)draulic cooling
fan
fan
Hydraulic pumpSpool valve45.8 mm1.803 in.
Rotor side clearanceSTD Drive rotor 0.02 mm0.0008 in.
Driven rotor 0.03 mm0.0012 in.
Limit Drive rotor 0.03 mm0.0012 in.
Driven rotor 0.04 mm0.0016 in.
Rotor body clearanceSTD 0.05±0.09 mm0.0020±0.0035 in.
Limit 0.10 mm0.0039 in.
Rotor tip clearanceSTD 0.02 mm0.0008 in.
Limit 0.03 mm0.0012 in.
Drive shaft bushing inside diameter17.00±17.05 mm0.6693±0.6713 in.
Drive shaft diameter16.97±16.98 mm0.6681±0.6685 in.
Drive shaft oil clearanceSTD 0.02±0.08 mm0.0008±0.0031 in.
Limit 0.08 mm0.0031 in.
Drive shaft preload (rotating torque)0.3 N Vm 3.0 kgf Vcm 2.6 in. Vlbf
Solenoid valve resistanceat cold 7.5±8.5

Hydraulic motorRotor side clearanceSTD0.01±0.04 mm0.0004±0.0016 in.
Limit 0.05 mm0.0020 mm
Drive shaft hole inside diameter14.000±14.011 mm0.5512±0.5516 in.
Drive shaft diameter13.973±13.984 mm0.5501±0.5506 in.
Drive shaft oil clearanceSTD 0.016±0.038 mm0.0006±0.0015 in.
Limit 0.04 mm0.0031 in.
Drive shaft preload (rotating torque)0.3 NVm 3.0 kgf Vcm 2.6 in. Vlbf
Water temp. Resistanceat 80 5C (176 5F)1.48±1.58 k

sensor
CO±64±
COOLIING SYSTEM Service Specifications
WhereEverybodyKnowsYourName

TORQUE SPECIFICATIONS
Part tightenedNVmkgf Vcmft Vlbf
Engine drain plug X Cylinder block1818013
Coolant filler plug X Water inlet housing44450 33
Water pump X Cylinder block18185 13
Water inlet housing X Water pump18185 13
Water inlet X Water inlet housing18185 13
Radiator fan shroud X Radiator4.950 43 in. Vlbf
Radiator X Body12120 9
Cooling fan reservoir tank X Radiator fan shroud4.950 43 in. Vlbf
Cooling fan inlet pipe X Radiator fan shroud4.950 43 in. Vlbf
Cooling fan pressure hose X Hydraulic motor64650 47
Radiator reservoir tank X Upper radiator support4.950 43 in. Vlbf
Radiator reservoir tank X Radiator reservoir tank support4.950 43 in. Vlbf
Hydraulic pump rear housing X End plug (for spool valve)19200 14
Hydraulic pump front housing X Rear housing21210 15
Hydraulic pump pulley X Drive shaft59600 43
Solenoid valve X Hydraulic pump rear housing39400 28
Hydraulic pump suction port union X Rear housing13135 10
 Hydraulic pump X Cylinder block 12 mm head 16 160 12
  14 mm head 20 310 22
\
 \
Cooling fan pressure hose X Hydraulic pump 64 650 47
\
 \
RH No.2 timing belt cover X Cylinder block 16 160 12
\
 \
Drive belt idler pulley X Hydraulic pump 37 380 27
\
 \
A/C compressor X Hydraulic pump 49 500 36
\
 \
A/C compressor X Cylinder block 49 500 36\
 \
A/C compressor stay X Oil filter bracket 29 300 22\
 \
Hydraulic motor cover X Motor housing 28 290 21\
 
\

\
Hydraulic motor X Radiator fan shroud
 

4.9
 

50
 

43 in.
Vlbf
\
 \
Cooling fan X Hydraulic motor 15 150 11
\
 \
Cooling fan oil cooler X Body 18 180 13
\
 \
Water temperature sensor X Radiator 7.4 75 65 in. Vlbf
±
COOLIING SYSTEM Service SpecificationsCO±65
WhereEverybodyKnowsYourName

PREPARATION
SST (SPECIAL SERVICE TOOLS)
 Illustration Part No. Part Name Note
 


 

09278±54012
 

Drive Shaft Holding Tool
 


Hydraulic pump pulley
 




 



09286±46011
 




Injection Pump
Spline Shaft Puller
 




Hydraulic pump pulley
 




 



09620±30010
 




Steering Gear Box
Replacer Set
 




 




 



(09627±30010)
 




Steering Sector Shaft
Bushing Replacer
 




Oil seal for hydraulic motor
 




 




(09631±00020)
 




(Handle)
 




Oil seal for hydraulic motor
 




 




09631±10030
 




Oil Seal Remover
 




Oil seal for hydraulic pump
 




 




09843±18020
 




Diagnosis Check
Wire 




RECOMMENDED TOOLS 

Illustration
 

Part No.
 

Part Name
 

Note
 




 




09025±00010
 




Small Torque
Wrench 




For measuring preload
 


 

09082±00015 


TOYOTA
Electrical tester 


 




 



09200±00010
 




Engine Adjust
Kit
 




 




 



09258±00030
 



Hose Plug Set
 




Plug for the vacuum hose, oil hose ect.
 




 




09904±00010
 




Expander
Set
 




Oil seal for hydraulic pump
 




 




09905±00013
 




Snap Ring
Pliers
 




Oil seal for hydraulic pump
CO±4±
COOLIING SYSTEM Preparation
WhereEverybodyKnowsYourName

EQUIPMENT
 Part Name\
 \
Note
 Caliper gauge\
 \
Hydraulic pump, Hydraulic motor
 Micrometer\
 \
Hydraulic pump, Hydraulic motor
 Precision straight edge\
 \
Hydraulic pump, Hydraulic motor Pressure gauge\
 \

 
Radiator cap tester\
 
\
 

Thermometer
\
 
\

\

 Torque wrench\
 \

 Vernier caliper\
 \
Hydraulic pump
COOLANT 

Item
 

Capacity
 

Classification
 
Item
 Liters US qts lmp. qts 
Classification
 Engine coolant 10.8 11.4 9.5 Ethylene±glycol base
LUBRICANT
 Item Capacity Classification
 Cooling fan fluid ± ATF DEXRON
[II
SSM (SPECIAL SERVICE MATERIALS) 

Part Name
 

Part No.
\
 

\
Use etc.
 


Seal packing 1282B,
Three bond 1282B or equivalent 


08826±00100\
 

\

Water pump, Water inlet housing
±
COOLIING SYSTEM PreparationCO±5
WhereEverybodyKnowsYourName