torque LEXUS SC400 1991 Service Repair Manual

(b) Apply battery voltage across the terminals.
(c) Check that the air flows from port E to the filter.
If operation is not as specified, replace the VSV.
4. REINSTALL VSV (a) Install the VSV with the bolt.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(b) Connect the following hoses:
(1) Vacuum hose (from EGR valve) to VSV
(2) Vacuum hose (from EGR vacuum modulator) to VSV
(c) Connect the VSV connector.
5. RECONNECT CABLE TO NEGATIVE TERMINAL OF BATTERY
INSPECTION OF EGR VACUUM
MODULATOR (Exc. USA Spec.)
1. DISCONNECT VACUUM HOSES FROM EGR VACUUMMODULATOR
Disconnect the three vacuum hoses from ports P, Q and R of
the EGR vacuum modulator.
2. INSPECT EGR VACUUM MODULATOR OPERATION (a) Block ports P and R with your finger.
(b) Blow air into port Q, and check that the air passesthrough to the air filter side freely.
(c) Start the engine, and maintain speed at 2,500 rpm.
(d) Repeat the above test. Check that there is a strong resistance to air flow.
3. RECONNECT VACUUM HOSES TO EGR VACUUM MODULATOR
Connect the three vacuum hoses to the proper locations.
EC±20
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) System
WhereEverybodyKnowsYourName

(b) Install the EGR valve with the two nuts.
Torque: 18 NVm (185 kgf Vcm, 13 ft Vlbf)
(c) Connect the following hoses:
(1) Water by±pass hose (from ISC valve) to the EGR valve
(2) Water by±pass hose (from rear water by±pass joint) to the EGR valve
8. RECONNECT EGR VALVE CONNECTOR
9. RECONNECT CABLE TO NEGATIVE TERMINAL OF BATTERY
10. REFILL WITH ENGINE COOLANT (See page CO±7)
INSPECTION OF EGR VALVE
(Exc. USA Spec.)
1. DRAIN ENGINE COOLANT (See page CO±6)
2. REMOVE EGR VALVE (a) Disconnect the following hoses:(1) Vacuum hose (from VSV) from EGR valve
(2) Vacuum hose (from VSV) from EGR vacuum
modulator
(3) Vacuum hose (from EGR vacuum modulator) f rom EGR valve
(4) Water by±pass hose (from ISC valve) from the
EGR valve
(5) Water by±pass hose (from rear water by±pass joint) from the EGR valve
(b) Disconnect the vacuum modulator bracket from the
EGR valve.
(c) Remove the two nuts, EGR valve and gasket.
EC±24
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) System
WhereEverybodyKnowsYourName

3. INSPECT EGR VALVECheck for sticking and heavy carbon deposits.
If a problem is found, replace the EGR valve assembly.
4. REINSTALL EGR VALVE (a) Place a new gasket on the EGR valve adaptor.
NOTICE:
w Do not touch the adaptor and EGR valve surfaces of the
gasket with your hand.
w Align the port holes of the gasket and adaptor.
Be careful of the installation direction.
(b) Install the EGR valve with the two nuts.
Torque: 18 N Vm (185 kgf Vcm, 13 ft Vlbf)
(c) Install the vacuum modulator bracket to the EGR valve.
(d) Connect the following hoses:
(1) Vacuum hose (from VSV) to EGR valve
(2) Vacuum hose (from VSV) to EGR vacuum modula- tor
(3) Vacuum hose (from EGR vacuum modulator) to EGR valve
(4) Water by±pass hose (from ISC valve) to the EGR
valve
(5) Water by±pass hose (from rear water by±pass joint) to the EGR valve
5. REFILL WITH ENGINE COOLANT (See page CO±7)
±
EMISSION CONTROL SYSTEMS Exhaust Gas Recirculation (EGR) SystemEC±25
WhereEverybodyKnowsYourName

COMPONENTS
REPLACEMENT OF CATALYTIC
CONVERTERS
(Front Catalytic Converter)
1. REMOVE CATALYTIC CONVERTER (FRONT)(a) Check that the converter is cool.
(b) Remove the two bolts and nuts holding the catalyticconverters to the front exhaust pipe.
(c) Disconnect the front exhaust pipe from the catalytic converter, and remove the gasket.
(d) Remove the four nuts holding the catalytic converter to the exhaust manifold.
2. REINSTALL CATALYTIC CONVERTER (a) Install a new gasket and the catalytic converter to theexhaust manifold with four new nuts.
Torque: 62 N Vm (630 kgf Vcm, 46 ft Vlbf)
(b) Install a new gasket to front end of the front exhaust
pipe, and torque the front exhaust pipe to the catalytic
converter.
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
EC±18±
EMISSION CONTROL SYSTEMS Three±way Catalyst (TWC) System
WhereEverybodyKnowsYourName

(Rear Catalytic Converter)
1. (USA Spec.)REMOVE SUB±OXYGEN SENSOR
Remove the two nuts and sub±oxygen sensor from the front
exhaust pipe.
2. REMOVE REAR CATALYTIC CONVERTER (FRONT EXHAUST PIPE)
(a) Remove the two bolts and nuts holding the front exhaust
pipe to the center exhaust pipe.
(b) Remove the two bolts and nuts holding the front exhaust
pipe to the front catalytic converter, and remove the front
exhaust pipe and two gaskets.
3. REINSTALL REAR CATALYTIC CONVERTER (FRONT EXHAUST PIPE)
Install the two new gaskets, the front exhaust pipe with the
four bolts and new nuts.
Torque: 43 N Vm (440 kgf Vcm, 32 ft Vlbf)
4. (USA Spec.)
REINSTALL SUB±OXYGEN SENSOR
Install the new gasket, the sub±oxygen sensor to the front ex-
haust pipe with the two nuts.
Torque: 18 N Vm (180 kgf Vcm, 13 ft Vlbf)
±
EMISSION CONTROL SYSTEMS Three±way Catalyst (TWC) SystemEC±19
WhereEverybodyKnowsYourName

 
Crankshaft Thrust clearance STD 0.020±0.220 mm (0.0008±0.0087 in.)
   Limit 0.30 mm (0.0118 in.)
  Thrust washer thickness  2.440±2.490 mm (0.0961±0.0980 in.)
  Main journal bore diameter on cylinder block  67.026±67.033 mm (2.8388±2.6391 in.)  
(with main bearing)
  
  
Main journal oil clearance
 
STD
 
0.026±0.045 mm (0.0010±0.0018 in.)   Limit 0.055 mm (0.0022 in.)  Main journal diameter  66.988±67.000 mm (2.6373±2.6378 in.) \
 \
Main bearing center wall thickness (Reference) 
   Mark 1 2.486±2.489 mm (0.0979±0.0980 in.)   Mark 2 2.489±2.492 mm (0.0980±0.0981 in.)   Mark 3 2.492±2.495 mm (0.0981±0.0982 in.)   Mark 4 2.495±2.498 mm (0.0982±0.0983 in.)
   Mark 5 2.498±2.501 mm (0.0983±0.0985 in.)
  Crank pin diameter  51.982±52.000 mm (2.0465±2.0472 in.)
  Circle runout Limit 0.08mm (0.0031 in.)
  Main journal taper and out±of±round Limit 0.02mm (0.0008 in.)
  Crank pin taper and out±of±round Limit 0.02mm (0.0008.in)
EGOC6±0C
TORQUE SPECIFICATION
 Part tightened  NVm kgf Vcm ft Vlbf
 No.1 idler pulley x Cylinder Block  34 350 25
 No.2 idler pulley x Cylinder block3435025
 Hydraulic pump x Cylinder block for 12 mm head 16 160 12

yy
for 14 mm head3031022 Crankshaft pulley x Crankshaft  245 2,500 181 Camshaft timing pulley x Camshaft  108 1,100 80 Timing belt tensioner x Oil pump  26 270 20 Spark plug x Cylinder head  18 180 13
 Drive belt tensioner x Cylinder block  16 160 12
 Generator x Generator bracket  37 380 27
 Generator x Cylinder block3738027
 Distributor housing x Cylinder head1818513
 Distributor rotor x Camshaft timing pulley3.83934 in.
lbf
 Distributor cap x Distributor housing3.83934 in.
lbf
 RH No.2 timing belt cover x Cylinder blockfor 12 mm head1818513
Drive belt idler pulley x Fan bracket3738027 
A/C compressor x Cylinder block4950036 A/C compressor x Fan bracket  49 500 36 A/C compressor stay x Oil filter bracket  29 300 22 Upper radiator support x Body  12 120 9 Exhaust manifold x Cylinder head  44 450 33
 Cylinder head x Cylinder block 1st 39 400 29
  2nd Turn 90 5  
 Camshaft bearing cap x Cylinder head  16 160 12
 Cylinder head cover x Cylinder head  5.9 60 52 in.Vlbf
Engine hanger x Cylinder head3738027 EGR pipe x RH exhaust pipe  18 185 13 Rear water bypass joint x Cylinder head  18 185 13
±
1UZ ± FE ENGINE ENGINE MECHANICALEG±209
WhereEverybodyKnowsYourName

 
Front water bypass joint x Cylinder head  18 185 13
 Intake manifold x Cylinder head1818513
Delivery pipe x Intake manifold1818513 
Fuel return pipe x Fuel pressure regulator
  
35
 
360
 
26 Fuel inlet hose x Delivery pipe  39 400 29  for SST 33 340 24 Cold start injector x Air intake chamber  7.8 80 69 in.Vlbf Air intake chamber x Intake manifold  18 185 13 EGR pipe x Air intake chamber  18 185 13
 EGR pipe x RH cylinder head  18 185 13
 Cold start injector tube x Air intake chamber  15 150 11
 Union (for brake booster) x Air intake chamber  29 300 22
 Throttle body x Air intake chamber  18 185 13
 IAC valve x Air intake chamber  18 185 13
 EGR valve adaptor x Air intake chamber  18 185 13
 EGR valve x EGR valve adaptor  18 185 13
Timing belt rear plate x Cylinder head7.88069 in. Vlbf 
Water outlet housing x Water pump
  
18
 
185
 
13 Main bearing stud bolt x Cylinder block  15 150 11 Main bearing cap x Cylinder block for nut (1st) 27 275 20  (2nd) Turn 90 5  
  for bolt 49 500 36 Connecting rod cap x Connecting rod 1st 25 250 18
  2nd Turn 905  
 Rear oil seal retainer x Cylinder block  7.8 80 69 in.Vlbf
 Water seal plate x Cylinder block  14 145 10
 Generator bracket x Cylinder block  18 185 13
 Oil pump x Cylinder block 12 mm head 16 160 12
  14 mm head 30 310 22
 No.1 oil pan x Cylinder block 10 mm head 7.8 80 69 in. Vlbf
12 mm head1818513 
No.1 oil pan x Oil pump
  
7.8
 
80
 
69 in. Vlbf No.1 oil pan x Rear oil seal retainer  7.8 80 69 in. Vlbf Oil strainer x Cylinder block  7.8 80 69 in. Vlbf Oil strainer x Oil pump  7.8 80 69 in. Vlbf Oil pan baffle plate x No.1 oil pan  7.8 80 69 in. Vlbf No.1 oil pan x No.2 oil pan  7.8 80 69 in. Vlbf
 Water pump x Cylinder block  18 185 13
 Water bypass pipe x Cylinder Block  18 185 13
 Knock sensor x Cylinder block  44 450 33
 Starter x Cylinder block  39 400 29
 Engine mounting bracket x Cylinder block  37 380 27
 Drive plate x Crankshaft  98 1,000 72
 Transmission x Cylinder block  57 580 42
 Transmission x No.1 oil pan  39 400 29
Drive plate x Torque converter3334025 Transmission oil cooler pipe x Transmission for union nut 34 350 25 Rear engine mounting member x Body  25 250 19\
 \
Rear engine mounting member x Rear engine mounting insulator1313510
EG±210±
1UZ ± FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

\
 \

Spring tester Valve spring
\
 
\

\
Steel square 

Valve spring
\
 
\

\

Thermometer 


\
 \
Torque wrench 
\
 
\

\
Valve seat cutter 


\
 
\

Vernier calipers 

EG0B1±0A
COOLANT
 Item Capacity Classification
 Engine coolant (w/ Heater) 10.8 liters (11.4 US qts, 9.5 lmp. qts) Ethylene±glycol base
EG0B1±10
LUBRICANT
 Item Capacity Classification
 Engine oil  API grade SG or SH, Energy±Conserving II
 Dry fill 6.0 liters (6.3 US qts, 5.3 lmp. qts) or ILSAC multigrade and recommended
 Drain and refill  viscosity oil with SAE 5W±30
 w/ Oil filter change 4.8 liters (5.1 US qts, 4.2 lmp. qts) being the preferred engine oil
 w/o Oil filter change 4.5 liters (4.8 US qts, 4.0 lmp. qts) 
EG0B1±0J
SSM (SERVICE SPECIAL MATERIALS)
 08826±00080 Seal packing or equivalent Camshaft bearing cap
   Cylinder head semi±circular plug
   Cylinder head cover
   Rear oil sear retainer
 08826±00080 Seal packing or equivalent Oil pump
   
   
   
 08826±00100 Seal Packing 1282B, Water inlet housing
  THREE BOND 1282B or equivalent Water seal plate
   Water pump
   
 08833±00070 Adhesive 1311, Drive plate bolt
  THREE BOND 1311 or equivalent 
   
   
 08833±00080 Adhesive 1344 No.1 idler pulley bolt
  THREE BOND 1344. 
  LOCTITE 242 or equivalent 
   
EG±8±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

23. REINSTALL THEFT DETERRENT HORN
(a) Install the theft deterrent horn with the bolt.
(b) Connect the connector.
24. REINSTALL RH CYLINDER HEAD COVER
(a) Remove any old packing (FIPG) material.
(b) Apply seal packing to the cylinder head as shown in theillustration.
Seal packing:Part No. 08826±00080 or equivalent
(c) Install the gasket to the cylinder head cover.
(d) Install the seal washer to the bolt.
(e) Install the cylinder head cover with the 8 bolts.
Torque: 5.9 N Vm (60 kgf Vcm, 52 in. Vlbf)
(f) Connect the 4 high±tension cords to the spark plugs.
(g) Connect the front high±tension cord clamp to the lower
high±tension cord cover.
(h) P l a c e t h e f r o n t h i gh±tension cord clamp to the rear
high±tension cord clamp.
(i) Install the 2 bolts holding the high±tension cord clamps to the
cylinder head cover.
(j) Connect the 5 high±tension cords to the front side of the front
high±tension cord clamp.
(k) Connect the No. 2 high±tension cord to the cord clamp on the
front high±tension cord clamp.
EG±26
±
1UZ±FE ENGINE ENGINE MECHANICAL
WhereEverybodyKnowsYourName

25. REINSTALL LH CYLINDER HEAD COVER
(a) Remove any old packing (FIPG) material.
(b) Apply seal packing to the cylinder head as shown in theillustration.
Seal packing:Part No. 08826±00080 or equivalent
(c) Install the gasket to the cylinder head cover.
(d) Install the seal washer to the bolt.
(e) Install the cylinder head cover with the 8 bolts.
Torque: 5.9 N Vm (60 kgf Vcm, 52 in. Vlbf)
(f) Connect the 2 engine wire connectors.
(g) Connect the 4 injector connectors.
(h) Install the engine wire protector to the 2 brackets on the
delivery pipe.
(i) Connect the 4 high±tension cords to the spark plugs.
(j) Connect the front high±tension cord clamp to the lower high±tension cord cover.
(k) P l a c e t h e f r o n t h i gh±tension cord clamp to the rear
high±tension cord clamp.
(l) Install the 2 bolts holding the high±tension cord clamps to the
cylinder head cover.
(m) Connect the 5 high±tension cords to the front side of the front
high±tension cord clamp.
±
1UZ±FE ENGINE ENGINE MECHANICALEG±27
WhereEverybodyKnowsYourName